Pacific Casual 217-H40-7D User manual

Questions, problems, missing parts? Before returning to the store,
call Our Customer Service
7.30 a.m. ~4.30p.m.PST, Monday - Friday,
888-445-6690
[email protected]
Model # 217-H40-7D
USE AND CARE GUIDE
Sarasota 7pc Cushioned Dining Set
(4 Dining Chairs and 2 Swivel Chairs)
Ver: 2-23-2021

2
Table of Contents
Care & Cleaning
Before using, wipe with a clean, dry cloth. Do not use bleach or solvents. Treat frame with one step liquid wax for maximum protection against
UV light and salty, damp air. When not in use, store furniture in a cool, dry place. If your set includes cushions, they may be cleaned by hand
with a mild solution of soap and water. Rinse cushion thoroughly and allow to drip dry. Do not machine wash or tumble dry, as cushions
may shrink. Do not use bleach or solvents on fabrics.
When cleaning the tabletop make sure to use a soft, clean cloth that doesn’t
bleed color as well.
Table of Contents .......................................................2
Important Safety Instructions ............................................2
Pre-Assembly....................................................................3
Planning Assembly ................................................................3
Hardware Included.................................................................. 3
Package Contents .................................................................. 4
Assembly..... ....................................................................
................................................................ 2
Care & Cleaning ..
.... .
....
..
Important Safety Instructions
IMPORTANT: Please check the tightness of the bolts
periodically.
CAUTION: Use the table and chairs on flat ground only.
READ ALL INSTRUCTIONS BEFORE USE
SAVE THESE INSTRUCTIONS
When using a furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this furnishing.
To reduce the risk of injury to persons:
a) Close supervision is necessary when this furnishing is used by or near children, or disabled persons, if applicable.
b) Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
6

3
Pre-Assembly
PLANNING ASSEMBLY
It will take two people about 60 minutes to complete the assembly process.
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA 32
BB Bolt (M6x32)32
32
DD
Bolt cap (M6)
Hex wrench 1
EE
Hardware for Two Swivel Chairs
AA BB DD EE
Hardware for Four Dining Chairs
Part Description Quantity
AA
Washer (M6)
24
BB Bolt (M6x32) 16
24
DD
Bolt cap (M6)
)02x6M(tloB 8
FF
AA BB DD
FF
CC
Lock washer (M6) 8
CC
Washer (M6)

Pre-Assembly (continued)
C
D
A1
C1
B1
E1
2
2
PACKAGE CONTENTS
Four Dining Chairs
A1
Part Description Quantity
A
Back panel 4
B Seat panel 4
C
Right armrest 4
D Left armrest 4
1 Back cushion 4
B
2Seat cushion 4
PACKAGE CONTENTS
Two Swivel Chairs
1
Part Description Quantity
A1
Back panel 2
B
1 Seat panel 2
C1 Right armrest 2
D1 D1 Left armrest 2
E1 U-bar
2
F1
Chair base 2
1 Back cushion 2
2
Seat cushion 2
F1
4

5
Assembly (Dining Chairs)
1Attaching armrests
2Attaching the back panel
□Place the right armrest (C) on its side on a flat, smooth surface.
□Align the seat panel (B) to the right armrest (C).
IMPORTANT: You
□
Align the back panel (A) to the armrests (C) and (D).
Attach the armrests (C) and (D) to the back panel (A) with washers (DD)
and bolts (BB) using the hex wrench (EE).
□Fully tighten all bolts (BB) once all bolts are in place.
IMPORTANT: You will need to align the seat panel (B) to
the proper armrest by lining up the bolt holes on each part.
IMPORTANT: YouIMPORTANT: Do not fully tighten bolts until the end of
Step 2.
Secure the seat panel (B) to the right armrest (C) with washers (DD)
and bolts (BB) using hex wrench (EE).
□
Repeat the above procedure to attach the left armrest (D).
□
□
BB
DD
BB
DD
EE
D
B
C
A
C
D
DD BB
DD BB EE
NOTE:
Please note that the assembly holes for the left and right
side of the back panel is offset to avoid miss assembly.
Place the back panel (A) with the curve facing outward
from the chair frame.

6
Assembly (Dining Chairs)
AA
C
AA
AA
3Attaching bolt caps
4Placing cushions
Place cushions (1 and 2) on the chair and secure the seat cushion
to the frame with hook and loop straps.
□Repeat steps 1 through 4 for the other dining chairs.
□
□Cover all bolts (BB) with bolt caps (AA).
1
2

Assembly (Swivel Chairs )
5Assembling the chair seat
6
□
Attaching the back panel
Place the right armrest (C1) on its side on a flat, smooth surface.
□Align the seat panel (B1) to the right armrest (C1).
IMPORTANT: You
□Align the back panel (A1) to the armrests (C1) and (D1).
Attach the armrests (C1) and (D1) to the back panel (A1) with washers (DD)
and bolts (BB) using the hex wrench (EE).
□Fully tighten all bolts (BB) once all bolts are in place.
IMPORTANT: You will need to align the seat panel (B1) to
the proper armrest by lining up the bolt holes on each part.
IMPORTANT: YouIMPORTANT: Do not fully tighten bolts until the end of
Step 6.
Secure the seat panel (B1) to the right armrest (C1) with washers (DD)
and bolts (BB) using hex wrench (EE).
□
Repeat the above procedure to attach the left armrest (D1).
□
□
BB
DD
A1
NOTE:
Please note that the assembly holes for the left and right
side of the back panel is offset to avoid miss assembly.
Place the back panel (A1) with the curve facing outward
from the chair frame.
BB
DD
B1
C1
D1
C1
D1
7

DDCC FF AA
AAAA
DD CC FF AA
E1
B1
F1
1
2
Assembly (Swivel Chairs)
7Attaching the U-bar to the seat
8Attaching the chair base
9Place cushions
□Place the cushions (1) and (2) on the swivel chair.
Secure them on the frame with fabric loops.
8
□
Attach the U-bar (E1) to the bottom of the seat panel (B1) with washers (DD)，
lock washers (CC) and bolts (FF) using hex wrench (EE).
□Once all the bolts are in place and fully tightened. Cover them all with bolt
caps (AA).
□Place the chair base (F1) on a flat, smooth surface.
□Plug the shaft of the U-bar into the center of the chair base (F1)
until an audible click is heard.
□Repeat Steps 5 through 9 for the other chair.