Pakedge Device & Software SE-5P2-EP User manual

pakedgedevice&software inc.
SE-5P2-EP
5 Port PoE Plus Powered Gigabit Ethernet Switch
with Two PoE portsPass-through
User Manual – Version 1.0
1

CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE, the essential
protection requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States relating to
electromagnetic compatibility.
FCC Certifications
This equipmenthas been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received; including interference that may cause undesired operation.
Trademarks:
All trade names and trademarks are the properties of Pakedge Device
& Software, Inc.
Copyright © 2014,All Rights Reserved.
2

INTRODUCTION:
The SE-5P2-EP is a compact, high-performance Gigabit Ethernet
switch equipped with five auto-speed-sensing 10/100/1000Mbps ports.
The switch will automatically negotiate with its connected partners on
the network speed and duplex mode.
The SE-5P2-EP has the option to be powered by a traditional A/C
adapter or by a PoE+ Source. Use of PoE input gives the user the
opportunity to install the switch in remote places where power outlets
are inaccessible.
The SE-5P2-EP also has the option to output PoE over two ports. If you
power the switch via the A/C adapter you will have two Ethernet ports
that can use PoE. You can also power the switch using an 802.3at PoE
Plus source and that will allow you to power the switch as well as still
provide two ports of PoE.
The capabilities of this PoE Passthrough switch mean PoE powered
devices can now be located further from wall power and in locations not
possible before because ofdistance limitations.
*CAUTION: Do not plug-in both the PoE and A/C Adapter. Doing so
may damage the switch.
The SE-5P2-EP delivers a dedicated 10/100/1000Mbps connection to
every attached client with no bandwidth congestion issue. It supports
auto MDI / MDI-X function as well as 9k jumbo frames, which mean
better network performance because the switch can send more data at
the same time. Each port could be used to connect to another switch
or hub with no crossover RJ-45cable.
The switch is plug-n-play without any software to configure and also
fully compliant with all network protocols. Its heavy duty metal chassis
design provides for proper cooling and makes it easy to place on a
desk or mount on a wall. In addition, the fan-less design results in
silent operation, which is especially important when it is mounted to a
wall.
Following contents in this package：
•One GigabitEthernet switch
•OneAC power adapter (optional)
•User’s manual
3

4

DEFINITION AND GUIDE:
LED definitions:
LED
Status
Operation
Power
Steady Blue
Power is on via power adapter
Off Power is off
PD
Steady Blue
Power is on via PoE input
Off
Power is off
PoE Steady Blue PoE is active on this port
Blinking Blue
PoE is not active on this port
Link/ACT
Steady Blue
Port connected
Blinking Blue
The port is transmitting/receiving data
Connection
Connection
Type
Speed
PoE
Power
DC Power
NA
NA
Port 1
Ethernet
10/100/1000
Mbps
802.3at
(PoE+) In
Ports 2-3
Ethernet
10/100/1000
mbps
802.3af
(PoE) Out
Ports 4-5
Ethernet
10/100/1000
Mbps
NA
5

Cable selection guide:
Network Speed
Cable Type
Max. Length
10Mbps Cat. 3, 4, 5 UTP/STP
328 feet (100
meters)
100Mbps Cat. 5 UTP/STP
328 feet (100
meters)
1000Mbps Cat. 5 UTP/STP
328 feet (100
meters)
6

SPECIFICATION:
Standard
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x full duplex operation and flow control
Interface
5* 10/100/1000Mbps RJ-45 Gigabit Ethernetports
Uplink
Auto MDI/MDI-X
（
Auto crossover
）
Network Speed
10/100/1000Mbps & Full/Halfduplex mode auto
detection (1000Mbps for Full duplex only)
MACAddr.Table
4K MAC entries
Buffer Memory
128K bits
Jumbo Frame
9K bytes
Mechanical
Dimensions- 5.87 x 3.31 x 1.02 (w x d x h, inches)
Weight- 10.5 oz.
Power Supply
ExternalAC PowerAdapter- 48V,0.8A
PoE Plus 48V,0.5A– 5W max
EMI
Mounting
CE, FCC class B
Wall mount bracket
7

TECHNICALSUPPORT:
Please visit our website for up-to-date support information:
Website:www.pakedge.com
Email: [email protected]
CONTACTINFORMATION:
Pakedge Device & Software Inc.
3847 Breakwater Avenue
Hayward,CA94545
U.S.A
© Pakedge Device & Software Inc. 2014 –All Rights Reserved
8