Pakedge Device & Software SK24 User manual

PAKEDGE
DEVICE&SOFTWARE INC.
SK Series
SK24, SK24f

1
FCC Declaration of Conformity
Pakedge Device & Software, Inc., 2847 Breakwater Avenue, Hayward, CA, declares under sole
responsibility that the SK series switches complies with 47 CFR Parts 2 and 15 of the FCC Rules as a Class
B digital device. These devices comply with Part 15 of FCC Rules. Operation of the devices is subject to
the following two conditions: (1) These devices may not cause harmful interference, and (2) these
devices must accept any interference that may cause undesired operation.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING WATER. CAUTION: DO
NOT OPEN THE UNIT. DO NO PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE
PERSONNEL. CAUTION: THIS DEVICE MUST BE INSTALLED AND USED IN STRICT ACCORDANCE WITH
THE MANUFACTURER’S INSTRUCTIONS AS DESCRIBED IN THE USER DOCUMENTATION THAT COMES
WITH THE PRODUCT. WARNING: POSTPONE INSTALLATION UNTIL THERE IS NO RISK OF
THUNDERSTORM OR LIGHTNING ACTIVITY IN THE AREA.
Safety Guidelines
Observe the following safety guideline to ensure your own personal safety and to help protect your
system from potential damage.
Basic Requirements
1. Keep the device strictly dry while storing, shipping and using;
2. Keep the device from fierce collision;
3. Follow the instructions provided in this manual to install the device;
4. Please contact the specified maintenance staff rather than remove the device on your own if any fault
happens.
Environmental Requirements
1. Temperature- Install the switch in a dry area, with ambient temperature between 0 and 70ºC(32 and
158ºF). Keep the switch away from heat sources such as direct sunlight, warm air exhausts, hot-air
vents, and heaters;
2. operating humidity -The installation location should have a maximum relative humidity of 90%, non-
condensing;
3. Ventilation- Do not restrict air flow by covering or obstructing air inlets on the sides of the switch.
Keep it at least 10cm free on all sides for cooling. Be sure there is adequate airflow in the room or wiring
closet where the switch is installed;
4. Operating conditions-Keep the switch away from nearest source of electromagnetic noise, such as
photo copy machines, microwaves, cellphones, etc.

2
Use Notes
1. Use the provided accessories, such as the cable, mounting kit, etc;
2. Ensure the basic supply voltage standard must be met;
3. Keep the power plug clean and dry in case of electric shock or other dangers;
4. Keep your hands dry while plugging cables;
5. Shutdown the device and power it off before unplugging cables;
6. Disconnect the power supply and pull out all cables, such as the power cord, fiber, Ethernet cable,
etc.in case of lightning storms.
7. Disconnect the power supply and pull out the plug if the device is out of use for extended periods of
time.
8. Keep the device far from water or other liquids;
9. Contact the specified maintenance staff if any problem occurs;
10. Do not tread on, drag or excessively bend its cable;
11. Do not use worn cables;
12. Do not directly look at the fiber interface in case of eye damage;
14. Prevent materials, such as metals, from entering the device through the ventilation hole;
15. Do not scrape or fray the device’s housing shell in case of abnormal operation or allergic reaction.
16. Keep the device out of reach from children.
Cleaning Notes
1. Shutdown the device and pull out all cables before cleaning it;
2. Use soft cloth to clean the device’s housing shell.
Environmental Protection
1. Throw the discarded device or batteries into the specified recycling places;
2. Observe local relevant packages, wasted batteries and discarded device processing acts and support
recycling action.

3
CONTENTS
Introduction .................................................................................................................................................. 5
Customer service and technical support ...................................................................................................... 5
ACCESSING THE WEB INTERFACE.................................................................................................................. 7
Dashboard..................................................................................................................................................... 9
Menu........................................................................................................................................................... 10
System ......................................................................................................................................................... 10
System Settings ........................................................................................................................................... 10
Basic Information ................................................................................................................................ 10
User Management .............................................................................................................................. 11
Safe Mangement ................................................................................................................................. 12
System reboot ..................................................................................................................................... 12
ACL .............................................................................................................................................................. 13
Standard IP .......................................................................................................................................... 13
Extended IP ......................................................................................................................................... 14
MAC IP................................................................................................................................................. 16
ACL Reference ..................................................................................................................................... 17
SNMP........................................................................................................................................................... 19
Community Name ............................................................................................................................... 19
Trap Target........................................................................................................................................... 21
Ports ............................................................................................................................................................ 22
Port Settings................................................................................................................................................ 22
Common Configuration....................................................................................................................... 23
Statistics .............................................................................................................................................. 23
Flow control ........................................................................................................................................ 23
BROADCAST STORM............................................................................................................................ 24
Port Rate Limit..................................................................................................................................... 25
Ag Group ............................................................................................................................................. 26
Mirror .................................................................................................................................................. 27
Mac Control................................................................................................................................................. 28
Binding configuration.......................................................................................................................... 28
FIlter Configuration ............................................................................................................................. 30
vlan.............................................................................................................................................................. 31

4
COnfiguration ...................................................................................................................................... 31
Traffic........................................................................................................................................................... 39
QOS ............................................................................................................................................................. 39
Apply ................................................................................................................................................... 39
STP............................................................................................................................................................... 41
COnfiguration ...................................................................................................................................... 41
POrt Configuration .............................................................................................................................. 42
IGMP Snooping ........................................................................................................................................... 44
Snooping ............................................................................................................................................. 44
Multicast group INfo ........................................................................................................................... 45
Management............................................................................................................................................... 45
Maintenance ............................................................................................................................................... 45
Configuration file ................................................................................................................................ 46
File UPload .......................................................................................................................................... 46
Log....................................................................................................................................................... 48
Global Set Up ...................................................................................................................................... 48
port setup Select ................................................................................................................................. 50
Neighbor INfo...................................................................................................................................... 50
POrt Statistics...................................................................................................................................... 51
Appendix A – Technical Support ................................................................................................................. 53
Appendix B- Specifications.......................................................................................................................... 54
Appendix C- Limited Warranty.................................................................................................................... 56

5
INTRODUCTION
The SK Series 24 port Smart Gigabit Switches provide 24 10/100/100. Mbps RJ45 ports, 2 Independent
1000Mbps fiber ports and one Console port. These switches support VLANs, QoS, DHCP relay, IGMP
snooping, ACL, STP, RSTP, port mirroring, link aggregation and other features. This switch provides great
performance for mid-sized home networks.
CUSTOMER SERVICE AND TECHNICAL SUPPORT
Pakedge Device & Software, Inc. is committed to providing you with exceptional support on all of our
products. If you wish to speak with one of our representatives, you may contact us at:
Customer Service
Email: [e-mail]
Phone: [phone]
Technical Support
Email: [email protected]
Phone: [phone]
Website: www.pakedge.com
Visit our website for up-to-date support information.
Please be prepared to provide your product's model and serial number when contacting Pakedge
Support. Your model and serial numbers are printed on a label located on the electronic housing.
Pakedge Device & Software, Inc.
3847 Breakwater Avenue
Hayward, CA 94545
USA

6
GETTING TO KNOW YOUR PRODUCT
Package Contents:
•SK Series Switch
•Power cord
•Rack Mount Set
The front panel of the SK switches has several blue LEDs. See Table1 below for more information.
Table 1: Front panel LED explanation from left to right.
LED
Status
Operation
POWER
Blue
The switch is powered on
Off
The switch is turned off
Off No PoE Compliant device is
connect to port
Ports 1-24 LINK/ACT
Blue
Port is online (link established)
Flashing Blue
Activity
Off
No device connected
The rear panel of the SX series switches has several blue LEDs and port connections. See table 2 below
for more information.
Table 2: Rear panel LED and port connection explanation from left to right.
Table 2: Rear Panel LED and Port Connection Explanation from Left to Right

7
LED
Status
Operation
Reset N/A Press and hold for about 10
seconds to factory reset the
switch
Sys
Blue
Switch is booting up
Flashing Blue
Switch is turned on
Off
Switch is powered off
Console
Blue
Switch is booting up
Flashing Blue
Activitys through console port
Off
No activity through port
SFP Port 25-26
Blue
Switch is booting up
Flashing Blue
Port is active and has activity
Off
Switch is off or SFP is not active
Reset Button
Note:
1. Please keep the switch in a dry and well ventilated environment.
2. Keep the work bench stable and well-earthed.
3. Do not restrict airflow covering or obstructing air in lets of the switch. Keep more than 10 centimeters
free on all sides for cooling. Be sure there is adequate air flow in the room or wiring closet where the
switch is installed.
4. Don’t put heavy articles on the Switch.
5. Make sure there is more than 1.5 centimeters vertical distance free between devices that stack each
other.
Connecting SFP Fiber Combo Ports
The small form-factor pluggable (SFP) module is a compact, hot-pluggable transceiver used for optical
signal transmission. Unlike other Pakedge Switches, both of these SFP ports are independent of the
copper ports. The SFP module accommodates a standard SFP module with an LC connector.
ACCESSING THE WEB INTERFACE
Pakedge X-Series switches contain a built-in web interface that is accessible through a standard web
browser. In order to connect to the switch, you must perform the following steps:
1. Connect the switch to power. This will turn on the LED lights and switch fans.
2. Connect a PC or laptop to any standard Ethernet port on the switch.
3. Configure the PC with IP address 192.168.1.10 and subnet mask 255.255.255.0. Open a
web browser.

8
4. Enter the switch's default IP address 192.168.1.205 into the address bar and press
<ENTER>.
5. A page will appear, prompting you for a username and password. Enter admin as the
username and leave the password field blank. Click OK to log in to the web
administration portal.
Note: It is recommended that you change this default password.
Once you have logged in to the switch, you will be able to configure changes. The following is an
example of the Dashboard page on the SK24

9
DASHBOARD
The dashboard provides frequently used quick links to help with more efficient setup.

10
MENU
The menu provides access to all of the configurable options on the switch. An example of the menu is
shown below.
These options are described in detail in this manual.
SYSTEM
The System section contains the four sub sections Systems Settings, IP Setting, ACL, SNMP
SYSTEM SETTINGS
There are four tabs under System Settings.
BASIC INFORMATION
The first option under System Settings is Basic Information. This page shows the basic information of a
switch. Here you can view the System Description, Firmware Version, and system start Time. None of
these setting can be changed within the GUI.

11
Further down, is the serial information, this is the information that you will need to console into the
switch.
The following three parameters can be changed on this page.
•Name – Give the switch a unique name.
•Location –Allows you to enter the location of the switch. Depending on your network
standards, you could enter the location of the switch within the building or pinpoint the
building and closet within your entire company.
•Contact – Contains information on whom to contact regarding switch inquiries. This is an
open text field that lets you enter names, addresses, phone numbers, email addresses, or
any other information regarding your contacts.
USER MANAGEMENT
The User Management page allows you to adjust settings to the user accounts that manage the switch.
To change the password to the switch, enter the Current Password and then enter the New Password.
You will need to Re-enter the new password. Click Apply towards the bottom to finalize the new
password.

12
You can also change the telnet password at the bottom. The telnet password will be used if you ever
need to access the switch via terminal, such as Putty or Hypertext terminal.
SAFE MANGEMENT
Safe Management determines by which methods users are allowed to access the switch. In this
example http and telnet are enabled, while snmp is disabled. In this example, the switch can be
accessed via telnet and http, but cannot be accessed via snmp.
SYSTEM REBOOT
The fourth tab under System Settings is System Reboot. Here you can soft reboot the switch by clicking
“system reboot.”

13
ACL
As traffic increases and the network grows, network security appears more and more important. Packet
filtering can effectively block unauthorized users from accessing network and control traffic volume on
the network for the purpose of conserving network resources. An access control list (ACL) implements
packet filter via configured rules and operations attached to a packet. When the switch receives a
packet, it analyzes the packet using currently applied ACL rules and then handles the packet by preset
operations.
The ACL section has 4 sections, standard IP, Extended IP, Mac IP, and ACL Reference.
STANDARD IP
The standard IP section allows you to allow or deny an IP address through the switch.
ACL Standard IP Group Number: Select the group number you would like to use, this is simply an
identification number. In this example, it has been set to 1.

14
ACE Number -ACE controls and monitors access to the object. In the above example this is set to 1.
Source IP Address –Specify the IP address that you would like to permit or deny.
Source Wildcard –This is used to determine the range of the IP addresses. In the above example, the
source IP address is 192.168.1.2, we want to include all IP addresses in the 192.168.1.x subnet.
Therefore the wild card is set to 0.0.0.255. There are 3 zeros because we are matching the IP up to the
first 3 octets.
Deny/Permit – choose whether you want to deny access or permit access for the rule you set up
above.
Once you are done with the changes click the “Add” button.
It will then show towards the bottom of the screen in the table.
*Note - To enable this rule to particular ports, please see the “ACL Reference Section”
EXTENDED IP
Extended IP gives you more specific options than the Standard IP. Below is an example of the page.

15
ACL Extended Group Num – Select the group number you would like to use, this is simply an
identification number. In this example, it has been set to 10.
ACE Number - ACE controls and monitors access to the object. In the above example this is set to 0.
Source IP – Specify source IP of packets for a rule to match.
Destination IP -Specify destination IP of packets for a rule to match.
Protocol Type –There are three protocol types, IGMP, IP, TCP, UDP. Select the protocol to match the
rule. If using the TCP or the UPD option you will be prompted to put in a source port and a destination
port. In the below example we are denying 192.168.1.55 through 192.168.1.205 from using the FTP
port.
Your rule will then show at the bottom of the screen as shown below. This section will show you all the
ACLs that you have set up. To view existing ACL’s, click on the dropdown menu next “please select”,
then select the ACL Group Number.

16
*Note - To enable this rule on particular ports, please see the “ACL Reference Section”
MAC IP
ACL Mac IP Group Num - Select the group number you would like to use, this is simply an identification
number. In this example, it has been set to 20.
ACE Num – ACE controls and monitors access to the object. In the above example this is set to 0.
Source/Destination MAC- Specify a source MAC and destination MAC of packets for the rule to match.
In this example aa:aa:bb:bb:cc:cc is the source and Destination Mac is dd:dd:ee:ee:ff:ff
Permit/Deny-Make sure to choose the radio button to permit or deny. In this example, the rule is set
to “permit”

17
*Note - To enable this rule to particular ports, please see the “ACL Reference Section”
ACL REFERENCE
The ACL Reference page allows you to apply your rules to ports on the switch.

18
Port - Select the port that you would like to apply or view the rule.
All ACL Groups- From this column, select the rule that you would like to use for the port number you
selected. Then click the add button, the rule will move over to the right hand column.
Reference ACL Groups-This is where your rules will show that are applied to the particular port
selected. To delete a rule, that is present in this field, select the rule and then “Delete.” The rule will
now only show up on the left hand column only, as shown below.

19
SNMP
SNMP allows a compliant device to broadcast its information. This information can be broadcasted to
other devices on the network. This can be useful for networking monitoring on devices such as Ihiji.
There are two sections, Community Name and Trap Target.
COMMUNITY NAME
The Community Name section is where you define the SNMP settings. Here is an example of the
Community Name page.