Pakedge Device & Software SW16-8PB User manual

pakedgedevice&software inc.
SW16-8PB
16 Port Fast Ethernet with 8 Port PoE Switch
User Manual
Version 1.2

This Equipment has been tested and found to comply with the limits for a
ClassAdigital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection againstharmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installedand used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of thisequipment in a residential area is likely to cause harmful
interference in which case the user willbe required to correct the
interference at their own expense.
This device complies with Part 15of the FCC Rules. Operation is subject
to the following two conditions: (1)this device may not cause harmful
interference, and (2) thisdevice must accept any interference received;
including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 classAfor ITE, the essential protection
requirement ofCouncil Directive 89/336/EEC on the approximation ofthe
laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. Nopart of this
document can be copiedor reproduced in any form without written
consent from the company.
Trademarks:
All tradenames and trademarks are the properties of their respective
companies.
Copyright © 2008,All Rights Reserved.

Unpacking Information
Thank you for purchasing this switch. Before
installation, please check that your package
contains the following items.
1. One 8+8 10/100 PoE Switch
2. One power cord
3. User’s Manual
Introduction
General Description
The device is a powerful, high-performance
Fast Ethernet Switch, with all 8 ports capable
of 10 or 100Mbps auto-negotiation operation
(NWay), which means the switch could
automatically negotiate with the connected
partners on the network speed and duplex
mode. It is ideal for micro-segmenting large
networks into smaller, connected subnets for
improved performance, enabling the
bandwidth demanding multimedia and
imaging applications. Moreover, the
10/100Mbps auto-sensing ability provides an
easy way to migrate 10Mbps to 100Mbps
network with no pain.
This switch supports PoE, which supplies
power for connected devices via CAT 5 and
above twisted cables. By integrating the data
transmitting cable and power cord, it

eliminates the effort constructing your
network. You could easily connect a Wireless
AP or a VoIP phone to this switch without
looking outlets for them. Over current
protection and circuit shorting protection are
also supported to ensure the safety.
The switch is plug-n-play without any software
to configure and also fully compliant with all
kinds of network protocols. Moreover, the rich
diagnostic LEDs on the front-panel provide the
operating status of individual port and whole
system.
Key Features
zComplies with 10BASE-T specifications of
the IEEE802.3 standard
zComplies with 100BASE-TX specifications
of the IEEE802.3u standard
zCompliant with IEEE 802.3af PoE standard
(DTE power via MDI-X)
zProvides 8 PoE ports with classification
identify
zSupports 15.4W maximum per PoE port
zSupports over current protection and
circuit shorting protection
z16 * RJ-45 ports for 100BASE-TX and
10BASE-T connectivity
zSupports NWay protocol for speed
(10/100Mbps) and duplex mode (Half/Full)
auto-detection

zSupports MDI/MDI-X auto crossover
zWire-speed packet filtering and forwarding
rate
zStore-and-forward architecture filters
fragment & CRC error packets
zSupports extensive LED indicators for
network diagnostics
zInternal universal switching power supply
zFCC Class A, CE, VCCI Class A
The Front Panel
The front panel consists of LED indicators
Please refer to the following paragraph for
detailed LED definition.
LEDs Definition
The switch contain 1* power LED for the
device, 1*10/100M LED for each port and
1*PoE LED for port 1 ~ port 8.

System LED:
LED Status
Operation
Power
Steady Blue
T
he switch is
powered on
Off
T
he switch is
powered off
Port LEDs
LED Status
Operation
10/100M
Blue
T
he port is connected
Blinking
Blue Data transmitting /receiving.
Off No valid link on this port
PoE
Blue One PoE compliant device is connecting
with this port.
Off
T
here is no PoE
compliant device
connecting with this
port.
The Rear Panel
The rear panel consists of one power
receptacle and 8 RJ-45 ports. Port 1 to Port 8
also support connecting to PoE devices.

Power Receptacle
To be compatible with the electric service
standards around the world, the switch is
designed to afford the power supply in the
range from100 to 240VAC, 50/60Hz. Please
make sure that your outlet standard to be
within this range.
To power on the switch, please plug the female
end of the power cord firmly into the
receptacle of the switch and the other end into
an electric service outlet. After the power cord
installation, please check if the power LED is lit
for a normal power status.
Installation
This switch can be placed on your desktop
directly, or mounted in a rack. The installation
is a snap. Users can use all the features of the
switch with simply attaching the cables and
turning the power on.
Before installing the switch, we strongly
recommend:
1. The switch is placed with appropriate
ventilation environment. A minimum
25mm space around the unit is
recommended.
2. The switch and the relevant components
are away from sources of electrical noise
such as radios, transmitters and
broadband amplifiers
3. The switch is away from environments

beyond recommend moisture
Desktop Installation
1. Install the switch on a level surface that
can support the weight of the unit and the
relevant components.
2. Plug the switch with the female end of the
provided power cord and plug the male end
to the power outlet.
Rack-mount Installation
Rack mounting facilitate to an orderly
installation when series of networking devices
circumstance needed. The switch is supplied
with rack mounting brackets and screws for
rack mounting the unit.
Procedures to Rack-Mounting the Switch in the
rack:
1. Disconnect all the cables from the switch
before continuing.
2. Place the unit the right way up on a hard,
flat surface with the front facing you.
3. Locate a mounting bracket over the
mounting holes on one side of the unit.
4. Insert the screws and fully tighten with a
suitable screwdriver.
5. Repeat the two previous steps for the other
side of the unit.
6. Insert the unit into the rack and secure
with suitable screws.
7. Reconnect all the cables.

Installation of Network Cables
1. Crossover or straight-through cable: All
the ports on the switch support
Auto-MDI/MDI-X functionality. Both
straight-through or crossover cables can be
used to connect the switch
2. Category 3, 4, 5 or 5e UTP/STP cable:
To make a valid connection and obtain the
optimal performance. Appropriate cables
corresponding to different
transmitting/receiving speed is required.
Please refer to the following table for
information:
Media Speed Wiring
10/100 Mbps
ports
10 Mbps
Category3,4,5
UTP/STP
100 Mbps Category 5
UTP/STP
Ports that
support PoE
(Port 1~Port8)
10/100 Mbps
Category5,5e
UTP/STP or
above.

Product Specifications
Standard
IEEE802.3 10BASE-
T
IEEE802.3u 100BASE-TX
IEEE802.3af
Power over Ethernet
IEEE802.3x flow control
Interface
16
* 10/100 Mbps auto
MDI/MDI-X RJ-45 ports
(Port1~8 support PoE power
feeding)
Network Data
Rate 10/100 Mbps Auto-negotiation
Transmission
Mode 10/100Mbps Full-duplex, Half-duplex
LED
indications System: Power
Ports: 10/100M, PoE
Emission FCC Class A,
CE, VCCI Class A
Power
Consumption 130W Max
Operating
Temperature 00~ 400C (320~ 1040F)
Operating
Humidity 10% - 90%(non-condensing)
Power Supply 48V 1.35A 100-240V/47-63 Hz universal
input

Technical Support
Please visit our website for up-to-date support
information:
Website: www.pakedge.com
Email: [e-mail]
CONTACT INFORMATION:
Pakedge Device & Software Inc.
1011 Edwards Road
Burlingame, CA 94010
© Pakedge Device & Software Inc. 2009
All Rights Reserved