Pakedge Device & Software SE-8P2-EP User manual

pakedgedevice&software inc
SE-8P2-EP
8 Port PoE Plus Powered Gigabit Ethernet Switch with
Two PoE Pass-through ports
or Four PoE Pass-through ports with AC adapter
User Manual –Version 1.0

FCC Certifications
This Equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received;
including interference that may cause undesired
operation.
CE Mark Warning
This equipment complies with the requirements relating
to the EMC Directive 2004/108/EC, the Low Voltage
Directive 2006/95/EC, and the RoHS Directive
2011/65/EU.
Company has an on-going policy of upgrading its

products and it may be possible that information in this
document is not up-to-date. Please check with your
local distributors for the latest information. No part of
this document can be copied or reproduced in any form
without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of
their respective companies.
Copyright © 2015, All Rights Reserved.

1
Unpacking Information
Thank you for purchasing this product. Before
installation, please verify that your package contains
the following items.
1. One Gigabit Ethernet High-power PoE Pass-
through Switch
2. Rubber feet *4
3. User’s Manual
4. One DC power adapter (optional)
5. One power cord (optional)
Introduction
General Description
The device is a powerful, high-performance Gigabit Ethernet
Switch, with all 8 ports capable of 10/100/1000Mbps auto-
negotiation operation (NWay), which means the switch
could automatically negotiate with the connected
partners on the network speed and duplex mode. It is
ideal for micro-segmenting large networks into smaller,
connected subnets for improved performance, enabling
the bandwidth demanding multimedia and imaging
applications. Moreover, the 10/100/1000Mbps auto-
sensing ability provides an easy way to migrate
10/100Mbps to 1000Mbps network with no pain.
This switch supports Power Over Ethernet pass-
through, having both PD (Powered Device) and PSE
(Power Sourcing Equipment) features in one single
device, which means the switch can obtain power from
the PD port by connecting to a PSE device and supply

2
power on the 4 PSE ports for connected devices via
CAT 5 or above twisted cables. By integrating the data
transmitting cable and power cord, it eliminates the
effort constructing your network. You can easily connect
a Wireless AP or a VoIP phone (PD devices) to this
switch without installing outlets for them. Over current
protection and circuit shorting protection are also
supported to ensure the safety.
The switch is plug-n-play without any software to
configure and also fully compliant with all kinds of
network protocols. Moreover, the rich diagnostic LED
indicators on the front-panel provide the operating
status of individual port and whole system.
Key Features
Provide 8x 10/100Mbps auto-detect half/full and
1000Mbs full duplex switch ports (IEEE802.3/
802.3u/ 802.3ab)
Supports MDI/MDI-X auto crossover
Supports one port PD power input complying with
high-power PD (IEEE802.3at) and an optional DC
power input in 48V (Power Adaptor).
Provides 4 PSE ports complying with IEEE802.3af
with classification identify
Supports over current protection and circuit
shorting protection
Supports up to 8K MAC address table
Supports maximum 9216 bytes jumbo packet
length forwarding at wire speed

3
Supports 128K Bytes frame buffer
Non-blocking switching performance
Supports IEEE 802.3x back-pressure flow control
for full duplex
Supports 802.3az Energy Efficient Ethernet
Supports Green Ethernet (Link-On Cable Length
Power Saving and Link-Down Power Saving)
Operation Temperature: 0~40℃
Humidity: 10%~90%RH, non-condensing
EMC: CE/FCC Class B
Safety: EN 60950-1
The Front Panel
The front panel consists of LED indicators.
For detailed LED definition, please refer to the next
paragraph.
The front panel of the switch is shown as below:

4
LED Definition
LED indicators for the device
Feature
Description
PWR LED
The switch is powered by the external
power adapter (DC 48V).
PD LED
The switch is powered by the PD port.
(high-power 60W).
PoE LED
It indicates the PoE connection status of
the port 1 to port 4. A steady green LED
indicates that a valid PD device is
connecting to the PoE port, while a
blinking LED indicates no valid PD
device been connected to the PoE port.
LNK/ACT
LED
- Steady green: Valid port connection.
- Blinking green: Valid port connection
and there is data transmitting/ receiving.
- Off: Port disconnected.
The Rear Panel
There are a DC jack for external power adapter
(optional) and 8 Ethernet ports for local switching on the

5
rear panel. All Ethernet ports feature 10/100/1000 Mbps
with auto-negotiation and auto MDI-X.
The rear panel of the switch is shown as below:
The rear panel port description
Feature
Description
Power
DC 48V
The DC 48V power adapter is optional if
local network could supply power to PD
port
Uplink /PD
10/100/1000Mbps Ethernet ports
feature with auto-negotiation and auto
MDI-X also could receive power from
Ethernet cable (high-power support).
Port 1~4
w/ PoE
10/100/1000Mbps Ethernet ports
feature with auto-negotiation and auto
MDI-X also with power supply provide
(IEEE 802.3af support).
Port 5~7
10/100/1000Mbps Ethernet ports
feature with auto-negotiation and auto
MDI-X.
Power could be provided on port 1~4 if there is sufficient
power available on the system.
This switch can power these combinations of devices:
Three class 0,3 PD device (3x15W) or
Four class 1 PD devices (4x4W) or

6
Four class 2 PD devices (4x7W) or
Three class 1 PD device and One class 2 PD
devices (3x4W +1x7W)
Two class 1 PD device and Two class 2
PD devices (2x4W +2x7W)
One class 1 PD device and Three class
2 PD devices (1x4W +3x7W)
NOTE:
A Powered Device (PD) is able to receive power
through an Ethernet cable connecting to its PD port.
Installation
Before installing the switch, we strongly recommend:
1. The switch is placed with appropriate ventilation
environment. A minimum 25mm space around the
unit is recommended.
2. The switch and the relevant components are away
from sources of electrical noise such as radios,
transmitters and broadband amplifiers.
3. The switch is away from environments beyond
recommend moisture.
■Steps of Installation
1. Attach the provided robber feet to the bottom of the
switch to keep the switch from slipping. The
recommend position has been square-marked.

7
2. Install the switch on a level surface that can
support the weight of the unit and the relevant
components.
3. Plug the switch with the Ethernet Cable on the PD
port, which is connecting to a PSE or Plug the
female end of the power adaptor on DC Jack to get
power.
Network Cables Installation
1. Crossover or straight-through cable: All the
ports on the switch support Auto-MDI/MDI-X
functionality. Both straight-through or crossover
cables can be used to connect the switch with PCs
as well as other devices like switches, hubs or
router.
2. Category 3,4,5,5e or 6 UTP/STP cable: To make
a valid connection and obtain the optimal
performance. Appropriate cables corresponding to
different transmitting/receiving speed is required.
To choose a suitable cable, please refer to the
following table.
Media
Speed
Wiring
10/100/1000
Mbps ports
10 Mbps
Category3,4,5
UTP/STP
100 Mbps
Category 5
UTP/STP
1000 Mbps
Category 5e, 6
UTP/STP

8
Ports that
support PoE
(Port 1~4)
10/100/1000
Mbps
Category5,5e,6
UTP/STP or
above
Product Specifications
Standard
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3ab 1000BASE-T
IEEE802.3x flow control
IEEE802.3at/af PoE standard
(DTE power via MDI)
IEEE802.3az Energy Efficient
Ethernet
Interface
8 * 10/100/1000 Mbps auto MDI/MDI-
X RJ-45 ports
(Port Uplink/PD support PoE power
receiving, Port 1~4 support PoE
power feeding)
Network Data
Rate
10/100/1000Mbps Auto-negotiation
Transmission
Mode
10/100Mbps: Full-duplex, Half-duplex
1000Mbps Full-duplex
LED
Indications
System: PWR, PD
Ports: Uplink, LNK/ACT, PoE
Memory
8K MAC address table
9216 bytes jumbo packet length
128K bytes buffer Memory
EMC
CE/FCC Class B
Safety
EN 60950-1

9
Operating
Temperature
00~ 400C (320~ 1040F)
Operating
Humidity
10% - 90%(non-condensing)
Power Supply
48V/1.25A Power Adaptor (Optional)