PAMAPIC ZHQ1580-WM-RM User manual

Instruction Manual
Electric Patio Heater
ZHQ1580-WM-RM
If you have any problem, please do not hesitate to
contact us via email:[e-mail]
Thank you for choosing our electric rose gold patio heater. This
Instructions Manual will provide you with valuable information
necessary for the proper care and maintenance of your new product.
Please take a few moments to thoroughly read the instructions and
familiarize yourself with all the operational aspects of your new heater.
•Unpack the electric rose gold heater marking sure that all the
items are present and that there are no components left in the box
and that the heater is free from any packing material.
•Using detailed drawing, follow the steps for assembling your
heater.
•Do not connect the heater to electrical supply until the assembly is
complete.
•Do not connect the heater to electrical supply if any of the
components or the power cord is damaged in any way.
•If in doubt contact your supplier.

IMPORTANT INSTRUCTIONS:
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock,
and injury to persons, including the following:
1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to
repair the heater yourself.
3. This heater is hot when in use. To avoid burns, do not let
bare skin touch hot surfaces. Do not move this heating
when still hot.
4. WARNING: Risk of fire - keep combustible material such as
furniture, papers, clothes, and curtains at least 3 feet (0. 9m)
from the front of heater and away from the sides and rear.
5. DO NOT place towels or other objects on the heater.
6. Extreme caution is necessary when any heater is used by or
near children or invalids and whenever the heater is left
operating and unattended.
7. Always unplug heater when not in use.
8. DO NOT operate any heater with a damaged cord or after
the heater malfunctions, has been dropped or has been
damaged in any manner, Return heater to authorized
service examination, electrical or mechanical adjustment, or
repair.
9. This heater is not intended for use in bathrooms, laundry
areas and similar Indoor locations. Never locate heater
where it may fall into a bathtub or other water container.
10. To protect against electrical hazards, DO NOT immerse in
water or other liquids.
11. DO NOT touch the control panel or plug in with wet hands.
12. DO NOT run cord under carpeting. DO NOT cover cord with
throw rugs, runners, or similar coverings. Arrange cord
away from traffic area and where it will not be tripped over.
13. To disconnect heater, turn controls to OFF, then remove
plug from outlet.
14. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.
15. To prevent a possible fire, DO NOT block the air intakes or
exhaust in any manner, DO NOT use on soft surfaces, like a
bed, where openings may become blocked.
16. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint, or flammable liquids
are used or stored.
17. Use this heater only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons. The use of attachments
not recommend or sold by unauthorized dealers may cause
hazards.
18. Always plug heaters directly into a wall outlet/receptacle.
Never use with an extension cord or relocatable power tap
(outlet/power strip).
19. Avoid use of an extension cord as the extension cord may
overheat and cause a risk of fire. However, if you have to
use an extension cord, the cord shall be in compliance with
the No.14 AWG minimum size and rated no less than
1875W.
20. CAUTION: Mount with bottom of heater at least 240cm from
floor, 25cm from the side wall, 50cm from ceiling.
21. This unit is designed for a 120V AC electrical outlet
connection ONLY.
22. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit, doing so will void your
warranty, The inside of the unit contains no user serviceable
parts. Only qualified personnel should perform all servicing
only.
23. Connect to properly grounded outlets only.
24. Children should be supervised to ensure that they do not
play with the appliance.
SAVE THESE INSTRUCTIONS
Warning
These appliances must be earthed.
Before installing or replacing the bulb, the appliance must be
always being disconnected from the 120V supply.
The appliance must be disconnected from the 120V supply
before the lid is opened.
The appliance must be installed exclusively in perfect
horizontal position.
Installation
Heater ZHQ 1580-WM-RM is built with the best quality
components in accordance to the prevailing legal regulations
and certified for safety in use. For best results from the
appliance please ensure that the installation is done by a
qualified electrician in accordance with the following instructions
and taking full account of current regulations. When using the
heater, please carefully follow the instructions and
recommendations below.
You could loosen the two M6*10 screws to change the best
Angle of heating. Then retighten them.

Installation to Wall
When fixing the heater to a wall, ensure hinges are in the
underside so that the lid hands down in the open position.
Minimum required distances:
a) 50cm from the side wall
b) 50cm from the ceiling
c) Installation height above 240cm
The heater must be fixed to a wall with the bracket supplied
to allow adequate ventilation.
Only use the rose gold heater on a firm solid vertical wall
where the Mounting Bar is in contact with the wall.
Wiring procedures and connections shall be in accordance
with the national and local jurisdiction.
Never fix or place heater near flammable or combustible
materials. Generally heaters must be placed at a safe
distance (clear space) of at least 2.0m from combustible
materials and glass walls.
If the heaters are placed in areas where spray painting of
any description is taking place, they should not be used
during the painting operations.
To reduce the risk of fire, do not store or use gasoline or
other flammable vapors and liquids in the vicinity of the
heater.
Accessories
Ref.
Name
Qty
1
Explosive bolt M6*50
4
2
M6 spanner
1
3
‘L’ hexagonal wrench
1
4
Remote control
1

Assembling Process
Step 1: Put 4 Explosive bolt M6*50①into the wall.
Step 2: Take off the nuts, the spring locks washers and the plain
washers from four explosive bolts. Keep them for the next step.
Step3: Installer the heater on the wall
Complete!

Operation
Connect the power cable to a 120V 13A supply which is located
in a safe, dry area.
The switch on the heater is used to control the Heater. When
the position mean on the 【ON】 , the first indicator light will
be turn red, the heater will be in standby mode. The【OFF】
position will turn off the Heater.
The panel control:
When the switch is on the 【ON】position, press the remote
control once, the heater will be on 1500W power. Press the
remote control again, the heater will be in standby mode.
You can also press the on the panel control . When
the switch is on the 【ON】position, press it once, the
heater will be on 1500W power. Press it again, the heater
will be in standby mode.
Although the patio heater is waterproof, do not use when
raining or in wet conditions.
Never connect the power cable from the electrical supply,
when the patio heater is not in use.
Grounding

MAINTENANCE
Unplug the unit and let it cool completely.
To keep this unit clean, the outer shell may be cleaned with
a soft, damp cloth. You may use a mild detergent if
necessary. After cleaning, dry the unit with a soft cloth.
DO NOT use alcohol, gasoline, abrasive powders, furniture
polish, or rough brushes to clean the heater. This may
cause damage or deterioration to the surface of the heater.
Although this heater is outdoor approved, DO NOT immerse
the heater in water for your safety.
Wait until the unit is completely dry before use.
STORAGE
When not in use, store this unit in a cool, dry location. To
prevent dust and dirt build-up, use the original packaging to
repack this unit.
TROUBLE SHOOTING
If this unit does not operate properly, please check the following
before repair or service:
Check if the power cord is plugged into an electrical outlet, if
not, plug in.
Check if electricity to the main fuse is working.
Make certain the power switches are turned on. If not,
choose a setting.
Technical specification
Ratings: 120V~ 60Hz
Power consumption: 1500 W
Insulation: class I