Panamax Power 360 P360-8 User manual

Instruction
Manual
for the
P360-8
POWER360 Features
SAC Outlets
8 surge protected AC outlets.
2 Modular Dual-Port USB chargers
Each Charging Station can charge up to two
devices simultaneously (2.1A capacity).
Protect or Disconnect
Keeps electronics safe from power spikes by
disconnecting load in a catastrophic event.
SmartGuard
Protects against brownouts and dangerous
over-voltage conditions. Disconnects
the
power when the incoming voltage falls below
95 Volts or rises above 140 Volts. Reconnects
when the voltage returns to a safe level.
Circle of Protection
LED indicator monitors the outlet wiring,
voltage and
protection status.
Coax and Telco Protection
Protects from surges on coax and telephone
signal lines, while maintaining full bandwidth
for high definition video and high speed
internet cable/DSL connections.
Lifetime Warranty
Limited lifetime product warranty
plus $500,000 connected
equipment
protection policy.
'"0
II
0
~
rn
;;o, I
g
I· I
• I
t
1· t-
t. -1
J - . 1 !
I f
,, ..---------
11 1
II
Caracterfsticas de POWER360
8 enchufes de corriente alterna
8 enchufes de corriente alterna protegidos
contra sobretensi6n.
2 cargadores USB modulares de dos
puertos
Cada estaci6n decarga puede cargar hasta dos
dispositivos
al mismo tiempo (capacidad 2. 1A) .
Tecnologia de protecci6n
Protege los productos electronicos de picos
de energfa al desconectarlos en caso de que se
produzcan incidentes.
Protecci6n inteligente
Protege contra cafdas de tension y condiciones
peligrosas
de sobretension. Desconecta Ia corriente
cuando Ia tension entrante cae por debajo de los
95 voltios o sube por encima de los 140 voltios.
Se reconecta cuando Ia tension vuelve a un nivel
seguro.
Circulo de protecci6n
El indicador LED refleja el estado del cableado de
los enchufes, el voltaje y Ia proteccion.
Coaxial y Protecci6n Telco
Protege de sobretensiones en lfneas coaxiales y
de serial de telefono, manteniendo un ancho de
banda completo para video de alta definicion y
las conexiones de cable/DSL de alta velocidad de
Internet.
Garantia de por vida
Garantfa de producto limitada de por vida, mas
polftica de protecci6n de 500 000$ para equipos
conectados.
This Package
Includes:
(1) POWER360 Eight Outlet Surge Protector
(2) Modular USB charging stations
(2) 6' micro- USB to USB cables
(to
connect charging station to base unit)
(2) Rubber feet for charging modules
(1) User manual
Este
paquete incluye:
(1) Protector de sobretension con ocho enchufes
POWER360
(2) Estacion de carga por USB modular.
(2) Cable de 1,8 m de micro-USB a USB.
(Para conectar Ia estacion de carga a Ia unidad
base)
(2) Pies de goma para el modulo decarga
(1) Manual del usuario
Ce pack comprend :
(1) Huit protections de surtension murales
POWER360
(2) Stations modulaires dechargement USB
(2) Cable micro-USB vers USB (6 pouces)
(pour connecter
Ia station de charge a l'unite de
base)
(2) Les pieds en caoutchouc pour le module
(1) Guilded'utilisateur
POWER360 Caracteristiques
8 prisesAC
8 Protecteurs de surtensions pour prises AC
2 Chargeurs modulaires adouble ports
USB
Chaque station de chargement peut chargerjusqu'a
deuxappareils
simultanement (capacite de 2,1 A).
Proteger ou Deconnecter
Protege votre equipement electronique en le
deconnectant en cas de hausse de tension lors d'un
sinistre.
SmartGuard
Protege contre les baisses de tension et les
conditions de surtension dangereuses. Deconnecte
!'alimentation lorsque Ia tension d'entree tom be
en dessous
de 95 Volts ou s'eleve au-dessus de 140
Volts, puis
Ia reconnecte lorsque Ia tension retrouve
un niveau stable et sur.
Cercle de protection
L'indicateur LED surveille l'etat du cablage de sortie,
de Ia tension et de Ia protection.
Protection Coaxiale et telephonique
Protege les Iignes telephoniques et les cables
coaxiaux
contre les ~urtensions tout en maintenant
Ia totalite de Ia bande passante de connexions
internet cable/ADSL pour vous assurer une vitesse
exceptionnelle et des videos en haute definition.
Garantie avie
Garantie limiteeavie du produit en complement
d'une politique de protection d'equipement
connecte de $500,000.

Properly Connecting Your
PANAMAX POWER360
To completely protect your equipment from surges, every wire leading
into or out of the equipment you want to protect must be connected
to the appropriate Panamax surge protector. Damaging lightning and
power surges can enter your system through any AC power or signal-line
(phone line, grounding wires, coax cables, modem cables, LAN cables,
etc.) connected to your electronic equipment.
The Panamax Connected Equipment Protection Policy is void if any
wire leading into or out of the equipment is not properly connected to
the appropriate Panamax surge protector. The surge protector must also
be plugged into a properly wired and grounded outlet. Please see the
warranty for details or contact the Panamax Tech Support Department
with questions.
Important Safety Points
Panamax POWER360 and the connected equipment must be indoors,
in a dry location and in the same building. Although your Panamax
POWER360 is very durable, its internal components are not isolated from
the environment. Do not install any Panamax product near heat emitting
appliances such as a radiator or heat register. Do not install this product
where excessive moisture is present; for example near a bathtub, sink,
pool, basement floor, fish tank, etc. It is not uncommon for a building to
be improperly grounded. In order to protect your equipment, Panamax
products must be plugged into a properly wired and grounded 3-wire
outlet. Additionally, building wiring and grounding must conform to
applicable NEC (USA) or CEC (Canada) codes for the Panamax protection
policy to be valid.
Circle of Protection
The CIRCLE OF PROTECTION provides peace of mind that your connected
equipment is safe. When all lights are blue, you can rest assured that
your electronics are protected.
1. PROTECTED
BLUE indicates that the POWER360 is functioning properly and that
all connected equipment is protected. OFF indicates that the power
is disconnected from the outlets. If this light is OFF and the VOLTAGE
light is illuminated BLUE, then the PROTECT OR DISCONNECT feature
in your POWER360 has protected your equipment from a catastrophic
surge event and disconnected power. Unplug all electronics from your
POWER360 and contact Panamax Tech Support for assistance.
2.WIRING
BLUE indicates that the wall outlet is properly wired and grounded.
RED indicates an open ground (no ground wire) or reverse wiring
(polarity) condition is detected. Unplug all electronics from your
POWER360 and contact Panamax Tech Support for assistance.
3.VOLTAGE
BLUE indicates that incoming voltage is within a safe range.
RED indicates an over-voltage or brownout condition and that
POWER360 has disconnected power to connected equipment to keep it
safe. POWER360 will automatically reset when voltage is back within a
safe range. If condition persists, it is advisable to contact an electrician
or your power company to determine the cause of the abnormal voltage
issue.
Installation
NOTE to TV ANTENNA, SATELLITE DISH and CATV INSTALLERS:
Articles 810.21 and 820.40 of the NEC provide specific guidelines for
proper grounding, and in particular, specify that the cable ground shall
be connected to the grounding system of the building, as close to the
point of cable entry as practical.
Installing (AC Power):
1. Turn OFF the power to all equipment that will be plugged into the
unit.
2. Make sure that the ON/OFF switch is in the OFF position. Plug the
unit into the wall outlet and then turn it ON.
3. Verify that the "Wiring" LED is BLUE, indicating that the wall outlet
is properly wired.
4. Plug the equipment to be protected into the POWER360 unit and,
one at a time, turn each piece of connected equipment ON and check
for correct operation.
S. Turn OFF the unit and all connected equipment before connecting
any signal lines.
Installing (Telephone Lines):
(Note: Telephone patch cables not included)
IMPORTANT: Note the position of the IN and OUT jacks on the
POWER360 unit. IN is for the line connection that comes from the
wall or floor jack. OUT is for the line connection to your connected
equipment. The protection circuit will only function if connected
properly. Reversed connections will pass the signal to the connected
equipment but will also prevent the protection· circuitry from
working and will invalidate the Panamax Connected Equipment
Protection Policy.
1. Make sure the POWER360 and all connected equipment is turned
OFF.
2. Take the incoming telephone line and plug it into the appropriate
IN jack on the protector. The line should now be connected between
the wall and the POWER360 unit.
3. Plug a telephone line (not included) into the OUT jack and then
plug the other end into the equipment to be protected.
4. Turn On the protector and the connected equipment. Verify that
each piece of connected equipment is receiving power and signal.
Installing (Coaxial Lines):
(Coaxial patch cables not included)
Note the position ofthe IN and OUT jacks on the POWER360 unit. IN
is for the line connection that comes from the wall or floor jack. OUT
is for the line connection to your connected equipment.
The POWER360 coaxial protection circuits achieve optimum signal
quality from Panamax's coaxial protectors that have the smallest
signal loss on the market -less than O.SdB of attenuation from OMHz
to 2.2GHz. Our coaxial protection has been specifically designed to
virtually eliminate signal loss to ensure HD video and high speed
internet performance is not compromised. The clamping level ·of 75
volts will meetthe demands of both cable and satellite voltage while
minimizing exposure to spikes and surges.
NOTE: The CATV/Sat/Antenna protection circuit in these models is
bi-directional and has been designed to work with cable TV systems
that send pay-per-view ordering information to the cable company
over the coaxial line.
Make sure that your equipment is connected to the proper jacks.
When used with diplexers, this protection circuit must be placed
between the diplexer and the Satellite receiver; it will not
protect the diplexer.
1. Make sure the Panamax protector and all connected equipment
is turned OFF.
2. Connect the coaxial cable from the CATV system, antenna, or
Satellite dish to the appropriate LINE connector on the POWER360.
3. Connect a coaxial cable from the EQUIP jack on the protector
to appropriate input jack on your TV, cable modem or Satellite
receiver.
USB Charging Station:
Your POWER360 includes two modular dual-port charging stations.
The unique, patent-pending design ofthese charging stations allows
them to be removed from the base unit and placed on a nearby desk
or table top for easy access.
The charging station must be tethered to, or plugged directly
into, your base unit to charge. A 6' tether cable is included for each
charging station. If you require a longer cable, various lengths of
standard USB-to-Micro USB cables are commonly available. Rubber
feet are included for your charging stations. Applied on the bottom
and towards the front of your charging station, they will help keep
your charging stations in place. Each charging station can handle up
to 2.1A capacity, typically enough for 2 mobile devices or 1 tablet. The
USB charging ports are surge-protected.
Wall Mounting:
Your POWER360 may be affixed to a wall or other flat surface.
1. Determine the mounting location. Hold the POWER360 unit
up against the location and mark drilling positions using the
mounting guides on the sides of the unit. Note: You are marking
the center point where you would like the unit to be mounted.
2. Drive a #6 screw into each drilling position.leave approximately
1/8" of space between the back of the screw head and the wall.
3. Position the POWER360 over the two screws and slide down to
lock into place.
4. Using the above procedure allows easy removal of the unit
by sliding up to disengage the unit from the screws.
Troubleshooting
The CIRCLE OF PROTECTION is not lit, there is no AC power
to my equipment, or my equipment doesn't turn on.
-Make sure POWER360 is plugged into a working AC outlet.
-Verify the "VOLTAGE" indicator on the CIRCLE OF PROTECTION
is Blue. If Red, the incoming line voltage is either too high
or too low and has been disconnected from your connected
equipment.
-Make sure the switch/circuit breaker is in the ON position.
- If you still have no power, POWER360 may be damaged.
Contact Panamax Tech Support.
My mobile device is not charging.
- Some devices may be incompatible with this USB charging
port. Although the device may report that it is not charging,
it is most likely to be charging at a lower (0.5 Amp) current.
- When charging two devices it is possible that that USB
charging circuitry may be overloaded. Disconnect one of the
devices.
- Make sure the tether cable is connected between the
charging station and base unit, or the charging station is
completely plugged into the base unit.
There is no audio or video from my cable box and/or my
cable modem Is not connecting.
-Check the coaxial connections, making sure they are correctly
and securely installed.
-Try a different coaxial cable.
- Bypass the coaxial connectors. If your picture returns, the
protector is damaged. Contact Panamax (website or Tech
Support Department) for replacement.
- If you still have no picture, a problem with your cable
provider's signal may exist.
(Note: Coaxial patch cables not included)
My telephone, DSL modem or fax machine has AC power
but still does not work.
-Check to see if your connected equipment is receiving a dial
tone.
-Try a different telephone cable, or try the equipment with a
different telephone jack.
- Bypass the telephone connectors. If your dial tone returns,
the protector is damaged. Contact Panamax (website or Tech
Support Department) for replacement.
- If you still have no dial tone, a problem with the phone
company's lines may exist.
The Panamax circuit breaker disconnects AC power from
the connected equipment.
- You have exceeded the ampere rating for your surge
protector. As a temporary fix, disconnect one or more pieces
of equipment. Ask your Panamax dealer about additional
Panamax protectors that may be required.
PANAMAX TECH SUPPORT: 1-800-472-5555
www.panamax.com/POWER360

Warranty and Connected Equipment Policy Information
CAUTION!
All
Panamax
Warranties
and
Connected
Equipment
Policies
are
valid
only
in
the
United
States
and
Canada.
CAUTION!
Audio/Video,
computer
and/or
telephone
system
installations
can
be
very
complex
systems,
consisting
of
many
interconnected
components.
Due
to
the
nature
of
electricity
and
surges,
a
single
protector
may
not
be
able
to
completely
protect
complex
installations
.
In
those
cases,
a
systematic
approach
using
multiple
protectors
must
be
employed.
Systematic
protection
requires
professional
design.
AC
power,
satellite
cables,
CATV
cables,
telephone/network
lines,
signal
lines
or
any
other
electrical
conductors,
entering
the
system
that
do
not
pass
through
this
surge
protector
may
invalidate
the
Panamax
Connected
Equipment
Protection
Policy.
For
additional
information
on
how
to
protect
your
system,
please
contact
Panamax
before
connecting
your
equipment
to
the
surge
protector.
CAUTION!
WARRANTY
LIMITATION
FOR
INTERNET
PURCHASERS
Panamax
products
purchased
through
the
Internet
do
not
carry
a
valid
Product
Warranty
or
Connected
Equipment
Protection
Policy
unless
purchased
from
an
Authorized
Pan
a
max
Internet
Dealer
and
the
original
factory
serial
numbers
are
intact
(they
must
not
have
been
removed,
defaced
or
replaced
in
any
way).
Purchasing
from
an
Authorized
Panamax
Internet
Dealer
insures
that
the
P.roduct
was
intended
for
consumer
use,
has
passed
all
quality
inspections
and
is
safe.
Buying
through
auction
sites
or
unauthorized
dealers
may
result
in
the
purchase
of
salvaged,
failed
and/or
products
not
intended
for
use
in
the
US.
In
addition,
Authorized
Panamax
Internet
dealers
have
demonstrated
sufficient
expertise
to
insure
warranty
compliant
installations.
For
a
list
of
Authorized
Panamax
Internet
Dealers
go
to
www.panamax.com.lf
you
have
any
questions
regarding
these
requirements,
please
contact
Panamax
Tech
Support.
Product
Upgrade
Program
If
your
Panamax
power
conditioner
sacrifices
itself
while
protecting
your
connected
equipment,
you
have
an
option
to
upgrade
to
the
latest
technology
.
Please
go
to
our
web
site
www.panamax.com
or
contact
Panamax
Tech
Support
at
800-472-5555
for
details.
Panamax
Surge
Protector
Lifetime
Limited
Product
Warranty
Panamax
warrants
to
the
purchaser
of
any
standard
Panamax
surge
protector
that
the
surge
protector
shall
be
free
of
defects
in
design,
material,
or
workmanship,
and
Panamax
will
repair
or
replace
any
defective
unit.
For
product
replacement
see
"NOTIFICATION"
(3)
.
Panamax
Surge
Protector
Limited
Connected
Equipment
Protection
Policy
It
is
the
policy
of
Panamax
that
it
will,
at
its
election,
either
replace,
pay
to
replace
at
fair
market
value,
or
pay
to
repair,
up
to
the
dollar
amount
specified
below,
equipment
that
is
damaged
by
an
AC
power,
cable,
telephone,
or
lightning
surge
while
connected
to
a
properly
installed
Panamax
power
conditioner.
To
be
eligible
for
compensation,
repair
and
or
replacement,
the
power
conditioner
must
shows
signs
of
surge
damage
or
that
it
is
operating
outside
of
design
specifications,
relative
to
its
surge
protection
ca
·
pability,
and
under
all
of
the
circumstances
failed
to
protect
your
connected
equipment.
$500,000
CONNECTED
EQUIPMENT
POLICY
THE
CONNECTED
EQUIPMENT
POLICY
IS
SUBJECT
TO
THE
FOLLOWING
CONDITIONS
AND
LIMITATIONS
1.
ORIGINAL
OWNERSHIP
REQUIREMENT:
Panamax's
connected
equipment
policy
extends
to
the
original
purchaser
of
the
Panamax
product
only
and
is
non-transferable.
Original
purchase
receipts
must
accompany
any
product
return
or
claim
for
connected
equipment
damage.
2.
PROPER
INSTALLATION:
Panamax
AC
protectors
must
be
directly
plugged
into
a
properly
grounded
3-wire
AC
outlet.
Extension
cords*,
non-grounded
two
prong
adapters,
or
other
non
-
Panamax
surge
products
must
not
be
used
.
Building
wiring
and
other
connections
to
protected
equipment
must
conform
to
applicable
codes
(NEC
or
CEC}
.
No
other
ground
wires
or
ground
connections
may
be
used.
All
wires
(including,
e.g
.,
AC
power
lines,
telephone
lines,
signal/data
lines,
coaxial
cable,
antenna
lead-ins)
leading
into
the
protected
equipment
must
first
pass
through
a
single
Panamax
protector
designed
for
the
particular
application.
The
protector
and
the
equipment
to
be
protected
must
be
indoors
in
a
dry
location,
and
in
the
same
building
.
Pan
a
max
installation
instructions
and
diagrams
must
be
followed
3.
NOTIFICATION:
You
must
notify
Panamax
within
ten
days
of
any
event
precipitating
request
for
product
replacement
or
payment
for
connected
equipment
damage.
A
return
authorization
(RA)
number
must
first
be
obtained
from
the
Panamax
Tech
Support
Department
at
www.panamax.com**
before
returning
the
protector
Panamax
.
At
this
time,
you
must
notify
Panamax
if
you
believe
you
have
a
claim
for
damaged
connected
equipment.
Once
you
obtain
an
RA
number,
please
mark
the
number
on
the
bottom
of
the
unit
and
pack
it
in
a
shipping
carton/
box
with
enough
packing
material
to
protect
it
during
transit.
The
RA
number
must
also
be
clearly
marked
on
the
outside
of
the
carton.
Ship
the
unit
Panamax.
Please
note
that
you
are
responsible
for
any
and
all
charges
related
to
shipping
the
unit
to
Panamax.
If
connected
equipment
damage
was
indicated
on
your
RA
request,
Panamax
will
mail
you
claim
kit
to
be
completed
and
returned
within
30
days
.A
connection
diagram
of
your
system
will
be
required
as
part
of
the
claim
kit.
Be
sure
to
note
its
configuration
before
disconnecting
your
equipment.
4.
DETERMINATION
OF
FAILURE:
Panamax
will
evaluate
the
protector
for
surge
damage
.
The
Panamax
protector
must
show
signs
of
surge
damage
or
must
be
performing
outside
(>
10%)
of
design
specifications
relative
to
its
surge
protection
capability.
Opening
the
enclosure,
tampering
with,
or
modifying
the
unit
in
any
way
shall
be
grounds
for
an
automatic
denial
your
request
for
payment.
Panamax
,
after
evaluating
all
information
provided,
will
determine
whether
or
not
your
request
is
eligible
for
payment.
If
the
surge
protector
shows
no
signs
of
AC
power
or
signal
line
surge
damage
and
is
working
within
design
specifications,
Panamax
will
return
the
unit
to
you
with
a
letter
explaining
the
test
results
and
notifying
you
of
the
rejection
your
claim
.
Exceptions
:
If
a
dealer
or
installer
replaces
the
protector
for
the
customer,
replacement
will
be
returned
to
the
dealer
installer;
or
if
the
protector
is
a
pre-1996
model,
it
will
be
replaced;
or,
for
a
Canadian
customer,
the
protector
will
be
replaced.
Panamax
reserves
the
right
to
inspect
the
damaged
connected
equipment,
parts,
or
circuit
boards.
Please
note
that
you
are
responsible
for
any
and
all
charges
related
to
shipping
the
damaged
equipment
to
Panamax.
Panamax
also
reserves
the
right
to
inspect
the
customer
's
facility
.
Damaged
equipment
deemed
uneconomical
to
repair
must
remain
available
for
inspection
by
Panamax
until
the
claim
is
finalized
.
S.
REQUEST
PAYMENTS:
Once
Panamax
has
determined
that
you
are
entitled
to
compensation,
Panamax
will,
at
its
election,
either
pay
you
the
present
fair
market
value
of
the
damaged
equipment,
or
pay
for
the
cost
of
the
repair,
or
send
you
replacement
equipment,
or
pay
the
equivalence
of
replacement
equipment.
6.
OTHER
INSURANCE/WARRANTIES:
This
coverage
is
secondary
to
any
existing
manufacturer's
warranty
,
implied
or
expressed,
or
any
insurance
and/or
service
contract
that
may
cover
the
loss
.
7.
EXCLUSIONS:
THE
PANAMAX
CONNECTED
EQUIPMENT
PROTECTION
POLICY
DOES
NOT
APPLYTO:
Service
charges,
installation
costs,
reinstallation
costs
;
setup
cost;
diagnostic
charges;
periodic
checkups;
routine
maintenance;
loss
of
use
of
the
product;
costs
or
expenses
arising
out
of
reprogramm
i
ng
or
loss
of
programming
and/or
data;
shipping
charges
or
fees;
service
calls;
loss
or
damage
occasioned
by
fire,
theft,
flood,
wind,
accident
,
abuse
or
misuse,
and
products
subject
to
manufacturer's
recall
or
similar
event.
8.
DISPUTE
RESOLUTION:
Any
controversy
or
claim
arising
out
ofor
relating
to
Panamax
's
Connected
Equipment
Protection
Policy,
or
the
alleged
breach
thereof,
shall
be
settled
by
arbitration
administered
by
the
American
Arbitration
Association
under
its
Commercial
Arbitration
Rules
.
You
may
file
for
arbitration
at
a
ny
AAA
location
in
the
United
States
upon
the
payment
of
the
applicable
filing
fee.
The
arbitration
will
be
conducted
before
a
single
arbitrator
,
and
will
be
limited
solely
to
the
dispute
or
controversy
between
you
and
Panamax.
The
arbitration
shall
be
held
in
any
mutually
agreed
upon
location
in
person,
by
telephone,
or
online.
Any
decision
rendered
in
such
arbitration
proceedings
will
be
final
and
binding
on
each
of
the
parties,
and
judgment
may
be
entered
thereon
in
a
court
of
competent
jurisdiction.
The
arbitrator
shall
not
award
either
party
special,
exemplary,
consequential,
punitive,
incidental
or
indirect
damages,
or
attorney
's
fees.
The
parties
will
share
the
costs
of
arbitration
(including
the
arbitrator's
fees,
if
any)
in
the
proportion
that
the
final
award
bears
to
the
amount
of
the
initial
claim.
9.GENERAL:
If
you
have
any
questions
regarding
the
product
warranty
or
the
connected
equipment
protection
policy,
please
contact
the
Panamax
Tech
Support
Department
at
www.panamax.com.
The
limited
Product
Warranty
and
Connected
Equipment
Policy
herein
supersede
all
previous
warranties
and/or
Connected
Equipment
repair/replacement
policies.
THE
LIMITED
PRODUCT
WARRANTY
IS
THE
ONLY
WARRANTY
PROVIDED
WITH
THIS
PANAMAX
PRODUCT
AND
ANY
OTHER
IMPLIED
OR
EXPRESSED
WARRANTIES
ARE
NON
-
EXISTENT;
This
warranty
may
not
be
modified
except
in
writing,
signed
by
an
officer
of
the
Pan
a
max
Corporation
.
*The
use
of
a
Panamax
extension
cord
or
equivalent
(Ul
orCSA
listed,
minimum
14AWG,
3-
wiregrounded)
will
not
invalidate
the
warranty.
**
Forms
are
available
on
the
Panamax
web
site
for
requesting
RAs
and
opening
a
claim
for
connected
equipment
damage.

POWER
60
TM
Circle
of
Protection
PANAMAX
TECH
SUPPORT:
1-
800-472-5555
www.panamax;com/POWER360
CABlEADO
CABlAGE
02014
(Ott
Brands,
LLC.
All
rights
reserved.
Panamax•
and
POWER360'"
are
ft9lslmd
trademarts
of
Core
Btands
,
LlC.
Designed
and
Engin
e
ered
in
the
USA.
Minufactured
to
Panamax
quaiUy
spe<lfications
In
China
.
TENSION