Panasonic KX-TGP700 Service manual

Administrator Guide
Base Unit for SIP Cordless Phone
Model No. KX-TGP700
Thank you for purchasing this Panasonic product.
Please read this manual carefully before using this product and save this manual for future use.
In this manual, the suffix of each model number is omitted unless necessary.
Document Version: 2020-07

Introduction
Outline
This Administrator Guide provides detailed information on the configuration and management of this unit.
Audience
This Administrator Guide contains explanations about the installation, maintenance, and management of the
unit and is aimed at network administrators and phone system dealers.
Technical descriptions are included in this guide. Prior knowledge of networking and VoIP (Voice over
Internet Protocol) is required.
Related Documentation
Quick Start Guide
Briefly describes basic information about the installation of the unit.
Operating Instructions
Describes information about the installation and operation of the unit.
Manuals and supporting information are provided on the Panasonic Web site at:
https://panasonic.net/cns/pcc/support/sipphone/
Technical Support
When technical support is required, contact your phone system dealer/service provider.
Trademarks
•Microsoft, Excel, Internet Explorer, Outlook, and Windows are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•Linux is a registered trademark of Linus Torvalds in the United States, other countries, or both.
•Firefox is a trademark of the Mozilla Foundation.
•Google Chrome is a registered trademark of Google Inc.
•All other trademarks identified herein are the property of their respective owners.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
NOTES
•The screen shots shown in this guide are provided for reference only, and may differ from the screens
displayed on your PC.
Introduction
2 Administrator Guide Document Version: 2020-04

Table of Contents
1 Initial Setup ............................................................................................. 9
1.1 Setup .............................................................................................................................. 10
1.1.1 Factory Defaults ........................................................................................................... 10
1.1.2 Language Selection for the Unit ................................................................................... 10
1.1.3 Basic Network Setup .................................................................................................... 10
1.1.4 Overview of Programming ............................................................................................ 14
1.1.5 Phone User Interface Programming ............................................................................. 14
1.1.5.1 Changing the Language for Phone User Interface Programming .............................. 14
1.1.6 Web User Interface Programming ................................................................................ 14
1.1.6.1 Password for Web User Interface Programming ....................................................... 15
1.1.6.2 Changing the Language for Web User Interface Programming ................................. 16
1.1.6.3 Before Accessing the Web User Interface ................................................................. 16
1.1.6.4 Accessing the Web User Interface ............................................................................ 18
1.2 Firmware Update ........................................................................................................... 22
1.2.1 Firmware Update .......................................................................................................... 22
2 General Information on Provisioning ................................................. 23
2.1 Pre-provisioning ............................................................................................................ 24
2.1.1 What is Pre-provisioning? ............................................................................................. 24
2.1.2 How to Obtain a Pre-provisioning Server Address ....................................................... 24
2.1.3 Server Address Formats ............................................................................................... 24
2.1.4 Obtaining a Provisioning Server Address via SIP PnP ................................................. 25
2.1.5 Obtaining a Provisioning Server Address from DHCP Options .................................... 26
2.2 Provisioning ................................................................................................................... 30
2.2.1 What is Provisioning? ................................................................................................... 30
2.2.2 Protocols for Provisioning ............................................................................................. 30
2.2.3 Configuration File ......................................................................................................... 30
2.2.4 Downloading Configuration Files .................................................................................. 32
2.2.5 Provisioning Server Setting Example ........................................................................... 38
2.2.6 Encryption ..................................................................................................................... 39
2.3 Priority of Setting Methods .......................................................................................... 40
2.4 Configuration File Specifications ................................................................................ 41
2.5 Configuration File Examples ........................................................................................ 42
2.5.1 Examples of Codec Settings ........................................................................................ 43
2.5.2 Example with Incorrect Descriptions ............................................................................ 43
3 Web User Interface Programming ....................................................... 45
3.1 Web User Interface Setting List ................................................................................... 46
3.2 Status ............................................................................................................................. 58
3.2.1 Version Information ....................................................................................................... 58
3.2.1.1 Base Unit ................................................................................................................... 59
3.2.1.2 Handset ..................................................................................................................... 59
3.2.2 Handset Information ..................................................................................................... 60
3.2.2.1 Handset Information .................................................................................................. 60
3.2.3 Network Status ............................................................................................................. 60
3.2.3.1 Network Common ...................................................................................................... 61
3.2.3.2 IPv4 ............................................................................................................................ 61
3.2.3.3 IPv6 ............................................................................................................................ 62
3.2.3.4 VLAN ......................................................................................................................... 63
3.2.4 VoIP Status ................................................................................................................... 64
3.2.4.1 VoIP Status ................................................................................................................ 64
3.3 Network .......................................................................................................................... 65
Table of Contents
Document Version: 2020-04 Administrator Guide 3

3.3.1 Basic Network Settings ................................................................................................. 65
3.3.1.1 IP Addressing Mode .................................................................................................. 66
3.3.1.2 IPv4 ............................................................................................................................ 66
3.3.1.3 IPv6 ............................................................................................................................ 68
3.3.2 Ethernet Port Settings .................................................................................................. 70
3.3.2.1 Link Speed/Duplex Mode ........................................................................................... 70
3.3.2.2 LLDP .......................................................................................................................... 71
3.3.2.3 CDP ........................................................................................................................... 71
3.3.2.4 VLAN ......................................................................................................................... 72
3.3.3 HTTP Client Settings .................................................................................................... 72
3.3.3.1 HTTP Client ............................................................................................................... 73
3.3.3.2 Proxy Server .............................................................................................................. 74
3.3.4 STUN Settings .............................................................................................................. 74
3.3.4.1 STUN ......................................................................................................................... 75
3.3.5 Multicast Paging Settings ............................................................................................. 75
3.3.5.1 Multicast Paging ........................................................................................................ 76
3.3.6 LDAP Settings .............................................................................................................. 77
3.3.6.1 LDAP ......................................................................................................................... 77
3.3.6.2 Server Common ......................................................................................................... 78
3.3.6.3 Server 1 - Server 16 .................................................................................................. 80
3.3.7 Xtended Service Settings ............................................................................................. 82
3.3.7.1 Xtended Service ........................................................................................................ 82
3.3.7.2 Xtended Service Settings [Line 1-16] ........................................................................ 83
3.3.8 UC Settings .................................................................................................................. 86
3.3.8.1 Presence Feature ...................................................................................................... 86
3.3.9 XML Application Settings .............................................................................................. 87
3.3.9.1 XML Application ......................................................................................................... 88
3.3.9.2 XML Phonebook ........................................................................................................ 89
3.3.10 TWAMP Settings .......................................................................................................... 89
3.3.10.1 TWAMP ...................................................................................................................... 90
3.4 System ............................................................................................................................ 91
3.4.1 System Settings ............................................................................................................ 91
3.4.1.1 System ....................................................................................................................... 91
3.4.2 Language Settings ........................................................................................................ 92
3.4.2.1 Selectable Language ................................................................................................. 93
3.4.2.2 Web Language .......................................................................................................... 95
3.4.3 User Password Settings ............................................................................................... 96
3.4.3.1 User Password .......................................................................................................... 97
3.4.4 Admin Password Settings ............................................................................................. 97
3.4.4.1 Admin Password ........................................................................................................ 98
3.4.5 Time Adjust Settings ..................................................................................................... 98
3.4.5.1 Synchronization ......................................................................................................... 99
3.4.5.2 Time Zone .................................................................................................................. 99
3.4.5.3 Daylight Saving Time (Summer Time) ....................................................................... 99
3.4.5.4 Start Day and Time of DST (Start Day and Time of Summer Time) ........................ 100
3.4.5.5 End Day and Time of DST (End Day and Time of Summer Time) .......................... 101
3.4.6 Handset Basic Settings .............................................................................................. 103
3.4.6.1 Handset 1–16 .......................................................................................................... 103
3.4.7 Handset Advanced Settings ....................................................................................... 104
3.4.7.1 Soft Key during IDLE Status -TPA60/65 .................................................................. 104
3.4.7.2 Soft Key during IDLE Status -TPA70/73 .................................................................. 106
3.4.7.3 Handset 1–16 .......................................................................................................... 107
3.4.8 Parallel Mode Settings ................................................................................................ 110
3.4.8.1 Parallel Mode ........................................................................................................... 110
3.4.9 Delete Handset ........................................................................................................... 110
Table of Contents
4 Administrator Guide Document Version: 2020-04

3.4.9.1 Delete Handset Registration .................................................................................... 111
3.5 VoIP ............................................................................................................................... 111
3.5.1 SIP Settings ................................................................................................................ 111
3.5.1.1 User Agent ............................................................................................................... 112
3.5.1.2 NAT Identity ............................................................................................................. 112
3.5.1.3 Advanced ................................................................................................................. 113
3.5.2 SIP Settings [Line 1]–[Line 16] ................................................................................... 113
3.5.2.1 Basic ........................................................................................................................ 114
3.5.2.2 Advanced ................................................................................................................. 116
3.5.3 VoIP Settings .............................................................................................................. 121
3.5.3.1 RTP .......................................................................................................................... 121
3.5.3.2 Voice Quality Report ................................................................................................ 122
3.5.4 VoIP Settings [Line 1]–[Line 16] ................................................................................. 124
3.5.4.1 Basic ........................................................................................................................ 124
3.5.4.2 Advanced ................................................................................................................. 126
3.6 Telephone ..................................................................................................................... 128
3.6.1 Multi Number Settings ................................................................................................ 129
3.6.1.1 Group Handset / Handset select for receiving call ................................................... 129
3.6.1.2 Handset and Line Number select for making call .................................................... 130
3.6.2 Call Control ................................................................................................................. 131
3.6.2.1 Call Control .............................................................................................................. 131
3.6.2.2 Emergency Call Phone Numbers ............................................................................ 134
3.6.3 Call Control [Line 1]–[Line 16] .................................................................................... 134
3.6.3.1 Call Features ........................................................................................................... 135
3.6.3.2 Dial Plan .................................................................................................................. 139
3.6.3.3 Call Rejection Phone Numbers ................................................................................ 139
3.6.4 Hotline Settings .......................................................................................................... 139
3.6.4.1 Hotline ...................................................................................................................... 140
3.6.5 Tone Settings .............................................................................................................. 140
3.6.5.1 Dial Tone .................................................................................................................. 141
3.6.5.2 Busy Tone ................................................................................................................ 142
3.6.5.3 Ringing Tone ............................................................................................................ 142
3.6.5.4 Stutter Tone ............................................................................................................. 143
3.6.5.5 Reorder Tone ........................................................................................................... 144
3.6.6 Import Phonebook ...................................................................................................... 144
3.6.6.1 Import Phonebook ................................................................................................... 145
3.6.7 Export Phonebook ...................................................................................................... 146
3.6.7.1 Export Phonebook ................................................................................................... 146
3.6.8 Flexible Key Settings for KX-TPA68 ........................................................................... 147
3.6.8.1 Flexible Key Settings for KX-TPA68 (No.1–12) ....................................................... 147
3.7 Maintenance ................................................................................................................. 148
3.7.1 Provisioning Maintenance .......................................................................................... 148
3.7.1.1 Provisioning Maintenance ........................................................................................ 149
3.7.2 Firmware Maintenance ............................................................................................... 150
3.7.2.1 Firmware Maintenance ............................................................................................ 151
3.7.3 Upgrade Firmware ...................................................................................................... 151
3.7.3.1 Upgrade Firmware ................................................................................................... 152
3.7.4 Import Wallpaper ........................................................................................................ 152
3.7.4.1 TPA60/65, UDT121,131 ........................................................................................... 152
3.7.4.2 TPA68 ...................................................................................................................... 153
3.7.4.3 TPA70/73 ................................................................................................................. 153
3.7.5 Export Logging File ..................................................................................................... 154
3.7.5.1 Export Logging File .................................................................................................. 154
3.7.6 Reset to Defaults ........................................................................................................ 154
3.7.7 Restart ........................................................................................................................ 155
Table of Contents
Document Version: 2020-04 Administrator Guide 5

3.7.7.1 Restart ..................................................................................................................... 155
3.7.7.2 Restart (Graceful) .................................................................................................... 155
3.7.8 DECT Monitoring ........................................................................................................ 155
3.7.8.1 Handset Status ........................................................................................................ 156
3.7.9 Call Status Monitoring ................................................................................................ 156
4 Configuration File Programming ...................................................... 159
4.1 Configuration File Parameter List .............................................................................. 160
4.2 General Information on the Configuration Files ....................................................... 182
4.2.1 Configuration File Parameters .................................................................................... 182
4.2.2 Characters Available for String Values ....................................................................... 183
4.3 System Settings .......................................................................................................... 184
4.4 Handset Registration Settings ................................................................................... 197
4.5 Basic Network Settings .............................................................................................. 198
4.6 Ethernet Port Settings ................................................................................................ 204
4.7 Pre-Provisioning Settings .......................................................................................... 206
4.8 Provisioning Settings ................................................................................................. 207
4.9 Firmware Update Settings .......................................................................................... 214
4.10 HTTP Settings .............................................................................................................. 215
4.11 HTTPD/WEB Settings .................................................................................................. 217
4.12 TR-069 Settings ........................................................................................................... 219
4.13 XML Settings ................................................................................................................ 224
4.14 XSI Settings ................................................................................................................. 227
4.15 XMPP (UC-ONE) Settings ........................................................................................... 232
4.16 LDAP Settings ............................................................................................................. 235
4.17 SNMP Settings ............................................................................................................. 244
4.18 Multicast Paging Settings ........................................................................................... 246
4.19 NTP Settings ................................................................................................................ 249
4.20 Time Settings ............................................................................................................... 249
4.21 Network Phonebook (Common) ................................................................................. 255
4.22 Language Settings ...................................................................................................... 256
4.23 NAT Settings ................................................................................................................ 259
4.24 SIP Settings ................................................................................................................. 261
4.25 SIP-TLS Settings ......................................................................................................... 289
4.26 CODEC Settings .......................................................................................................... 292
4.27 DTMF Settings ............................................................................................................. 294
4.28 RTP/RTCP/RTCP-XR Settings .................................................................................... 295
4.29 SRTP Settings .............................................................................................................. 298
4.30 VQ Report by PUBLISH ............................................................................................... 301
4.31 uaCSTA Settings ......................................................................................................... 303
4.32 Telephone Settings ..................................................................................................... 305
4.33 Flexible Key Settings for KX-TPA68 .......................................................................... 322
4.34 Tone Settings ............................................................................................................... 325
4.35 Call Control Settings ................................................................................................... 333
4.36 Logging Settings ......................................................................................................... 358
4.37 TWAMP Settings .......................................................................................................... 363
5 Useful Telephone Functions .............................................................. 365
5.1 Line Settings ................................................................................................................ 366
5.1.1 Multi Number Settings ................................................................................................ 366
5.2 Phonebook Import and Export ................................................................................... 369
5.2.1 Import/Export Operation ............................................................................................. 371
5.2.2 Editing with Microsoft Excel ........................................................................................ 372
5.2.3 Exporting Data from Microsoft Outlook ....................................................................... 375
5.3 Dial Plan ....................................................................................................................... 375
Table of Contents
6 Administrator Guide Document Version: 2020-04

5.3.1 Dial Plan Settings ....................................................................................................... 375
5.4 Broadsoft XSI (Xtended Services Interface) ............................................................. 378
5.4.1 Outline ........................................................................................................................ 378
5.4.2 XSI Service Settings ................................................................................................... 379
5.5 BroadCloud (Presence) .............................................................................................. 380
5.5.1 Outline ........................................................................................................................ 380
5.5.2 BroadCloud (Presence) Function Settings ................................................................. 381
5.5.3 Handset Operation of BroadCloud (Presence) Functions .......................................... 381
5.6 Pairing (Parallel Mode) ................................................................................................ 382
5.6.1 Outline ........................................................................................................................ 382
5.6.2 Pairing (Parallel Mode) Settings ................................................................................. 383
5.7 Flexible Key Setting for KX-TPA68 ............................................................................ 386
6 Firmware Update ................................................................................ 389
6.1 Firmware Server Setup ............................................................................................... 390
6.2 Firmware Update Settings .......................................................................................... 390
6.3 Executing Firmware Update ....................................................................................... 391
6.4 Upgrade Firmware ....................................................................................................... 392
7 Troubleshooting ................................................................................. 393
7.1 Troubleshooting .......................................................................................................... 394
Table of Contents
Document Version: 2020-04 Administrator Guide 7

Table of Contents
8 Administrator Guide Document Version: 2020-04

Section 1
Initial Setup
This section provides an overview of the setup
procedures for the unit.
Document Version: 2020-04 Administrator Guide 9

1.1 Setup
1.1.1 Factory Defaults
Many of the settings for this unit have been configured before the unit ships.
Where possible, these settings are configured with the optimum or most common values for the setting. For
example, the port number of the SIP (Session Initiation Protocol) server is set to "5060".
However, many of the settings, such as the address of the SIP server or the phone number, have not been
pre-configured, and they must be modified depending on the usage environment. If the port number of the
SIP server is not "5060", the value of this setting must be changed.
This unit thus will not function properly using only the factory default settings. The settings for each feature
must be configured according to the environment in which the unit is used.
Note
•If you are using a PoE hub, the number of devices that you can connect simultaneously is limited by
the amount of power supplied by the hub.
1.1.2 Language Selection for the Unit
You can change the language used on the LCD.
In addition, various settings can be configured by accessing the Web user interface from a PC on the same
network (→ see 3 Web User Interface Programming). You can select the language for the Web user
interface.
Note
•To select the display language for the unit, refer to the Operating Instructions on the Panasonic Web
site (→ see Introduction).
•To select the display language for the Web user interface, see 3.4.2 Language Settings.
1.1.3 Basic Network Setup
This section describes the basic network settings that you must configure before you can use the unit on
your network.
You must configure the following network settings:
•IP Address Mode (IPv4 or IPv6 or IPv4/IPv6 Dual) settings
•TCP/IP settings (DHCP / RA for IPv6 / static IP)
•DNS server settings
For details about basic network settings via the Web user interface, see 3.3.1 Basic Network Settings.
TCP/IP Settings for IPv4 (DHCP or Static IP Address Assignment)
A unique IP address must be assigned to the unit so that it can communicate on the network. How you
assign an IP address depends on your network environment. This unit supports the following 2 methods for
assigning an IP address:
Obtaining an IP Address Automatically from a DHCP Server
You can configure the unit to automatically obtain its IP address when it starts up from a DHCP server
running on your network. With this method, the system can efficiently manage a limited number of IP
addresses. Note that the IP address assigned to the unit may vary every time the unit is started up.
For details about the DHCP server, consult your network administrator.
1.1 Setup
10 Administrator Guide Document Version: 2020-04

Using a Static IP Address Specified by Your Network Administrator
If IP addresses for network devices are specified individually by your network administrator, you will need to
manually configure settings such as the IP address, subnet mask, default gateway, and DNS servers.
For details about the required network settings, consult your network administrator.
TCP/IP Settings for IPv6 (DHCP, RA or Static IP Address Assignment)
A unique IP address must be assigned to the unit so that it can communicate on the network. How you
assign an IP address depends on your network environment. This unit supports the following 3 methods for
assigning an IP address:
Obtaining an IP Address Automatically from a DHCP Server
You can configure the unit to automatically obtain its IP address when it starts up from a DHCP server
running on your network. With this method, the system can efficiently manage a limited number of IP
addresses. Note that the IP address assigned to the unit may vary every time the unit is started up.
For details about the DHCP server, consult your network administrator.
Using a Static IP Address Specified by Your Network Administrator
If IP addresses for network devices are specified individually by your network administrator, you will need to
manually configure settings such as the IP address, Prefix, default gateway, and DNS servers.
For details about the required network settings, consult your network administrator.
Using a RA (Router Advertisement)
An IPv6 address can be assigned using Stateless Autoconfiguration. This enables the setting of addresses
for only the router and the node without the need to manage information.
For details about the required network settings, consult your network administrator.
DNS Server Settings
You can configure the unit to use 2 DNS servers: a primary DNS server is DNS1 and a secondary DNS
server is DNS2. The primary DNS1 server receives priority over the secondary DNS2 server. If the primary
DNS1 server returns no reply, the secondary DNS2 server will be used.
For details about configuring the DNS server settings using the unit, or using the Web user interface, see
Configuring the Network Settings of the Unit in this section.
DNS Priority Using Configuration File
The setting for DNS server(s) may be configured using the configuration files by your phone system dealer/
service provider (→ see "DHCP_DNS_ENABLE", "DHCP_DNS_ENABLE_IPV6",
"USER_DNS1_ADDR"/"USER_DNS2_ADDR" (for IPv4) and
"USER_DNS1_ADDR_IPV6"/"USER_DNS2_ADDR_IPV6" (for IPv6) in 4.5 Basic Network Settings).
•When "DHCP_DNS_ENABLE" (for IPv4) is set to "Y", you can manually configure the DNS server address
by using "USER_DNS1_ADDR" or ("USER_DNS1_ADDR" and "USER_DNS2_ADDR"). When set to "N", the
DNS server address will be automatically transmitted. This setting is available only when
("IP_ADDR_MODE"="0" or "IP_ADDR_MODE"="2") and "CONNECTION_TYPE"="1".
•When "DHCP_DNS_ENABLE_IPV6" (for IPv6) is set to "Y", you can manually configure the DNS server
address by using "USER_DNS1_ADDR_IPV6" or ("USER_DNS1_ADDR_IPV6" and
"USER_DNS2_ADDR_IPV6"). When set to "N", the DNS server address will be automatically transmitted.
This setting is available only when ("IP_ADDR_MODE"="1" or "IP_ADDR_MODE"="2") and
"CONNECTION_TYPE_IPV6"="1".
Configuring the Network Settings of the Unit
The following procedures explain how to change the network settings via the unit.
For details about the individual network settings that can be configured via the unit, refer to the Operating
Instructions on the Panasonic Web site (→ see Introduction).
1.1.3 Basic Network Setup
Document Version: 2020-04 Administrator Guide 11

For details about configuring network settings via the Web user interface, see 3.3.1 Basic Network
Settings.
To configure IP Mode (IPv4, IPv6, IPv4&IPv6)
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IP Mode Select"*1 → /[CENTER]
5. []/[ ]: "<IPv4>"/"<IPv6>"/"<IPv4&IPv6>" → /[CENTER]
•The initial value is "IPv4".
Configuring the Network Settings Using IPv4
To configure network settings automatically
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. []/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IPv4 Settings" → /[CENTER]
5. [ ]/[ ]: "Connection Mode"*1 → /[CENTER]
6. [ ]/[ ]: "Connection Mode <DHCP>"
7.
To configure network settings manually
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IPv4 Settings" → /[CENTER]
5. []/[ ]: "Connection Mode"*1 → /[CENTER]
6. [ ]/[ ]: "Connection Mode <Static>"
7. Enter the IP address, subnet mask, default gateway, DNS1 (primary DNS server), and, if necessary,
DNS2 (secondary DNS server), and then press .
8.
1.1.3 Basic Network Setup
12 Administrator Guide Document Version: 2020-04

Configuring the Network Settings Using IPv6
To configure network settings automatically using DHCP
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IPv6 Settings" → /[CENTER]
5. []/[ ]: "Connection Mode"*1 → /[CENTER]
6. []/[ ]: "Connection Mode <DHCP>"
7.
To configure network settings automatically using RA
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IPv6 Settings" → /[CENTER]
5. [ ]/[ ]: "Connection Mode"*1 → /[CENTER]
6. [ ]/[ ]: "Connection Mode <RA>"
7. Enter the addresses for DNS1 (primary DNS server) and, if necessary, DNS2 (secondary DNS server)
manually, and then press .
8.
To configure network settings manually
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "System Settings" → /[CENTER]
3. [ ]/[ ]: "Network Settings" → /[CENTER]
4. [ ]/[ ]: "IPv6 Settings" → /[CENTER]
5. [ ]/[ ]: "Connection Mode"*1 → /[CENTER]
6. [ ]/[ ]: "Connection Mode <Static>"
7. Enter the IP address, Prefix (for IPv6), Default Gateway, DNS1 (primary DNS server), and, if necessary,
DNS2 (secondary DNS server), and then press .
1.1.3 Basic Network Setup
Document Version: 2020-04 Administrator Guide 13

8.
*1 The current setting is displayed below.
Note
•If your phone system dealer/service provider does not allow you these settings, you cannot change
them even though the unit shows the setting menu. Contact your phone system dealer/service
provider for further information.
•If you select DHCP for the connection mode, all the settings concerning static connection will be
ignored, even if they have been specified.
•If you select DHCP for the connection mode and Auto for DNS, the DNS server settings (DNS1 and
DNS2) will be ignored, even if they have been specified.
1.1.4 Overview of Programming
There are 3 types of programming, as shown in the table below:
Programming
Type Description References
Phone user
interface
programming
Configuring the unit’s settings directly from the unit. → 1.1.5 Phone User
Interface Programming
Web user
interface
programming
Configuring the unit’s settings by accessing the Web
user interface from a PC connected to the same
network.
→ 1.1.6 Web User Interface
Programming
→ 3 Web User Interface
Programming
Configuration file
programming
Configuring the unit’s settings beforehand by
creating configuration files (pre-provisioning), and
having the unit download the files from a server on
the Internet and configure its own settings
(provisioning).
→ 2 General Information on
Provisioning
→ 4 Configuration File
Programming
1.1.5 Phone User Interface Programming
You can change the settings directly from the unit.
For details about the operations, refer to the Operating Instructions on the Panasonic Web site (→ see
Introduction).
1.1.5.1 Changing the Language for Phone User Interface
Programming
You can change the language used on the LCD. Because the language settings for the LCD of the unit are
not synchronized, you must set the languages individually for the unit.
For details about changing the setting, refer to the Operating Instructions on the Panasonic Web site (→ see
Introduction).
1.1.6 Web User Interface Programming
After connecting the unit to your network, you can configure the unit’s settings by accessing the Web user
interface from a PC connected to the same network. For details, see 3 Web User Interface Programming.
1.1.4 Overview of Programming
14 Administrator Guide Document Version: 2020-04

A
B
D
E F G
C
A. Router
B. Switching Hub
C. PC
D. KX-TGP700
E. KX-TPA60/KX-TPA70/KX-TPA73
F. KX-TPA65
G. KX-TPA68
1.1.6.1 Password for Web User Interface Programming
To program the unit via the Web user interface, a login account is required. There are 2 types of accounts,
and each has different access privileges.
•User: User accounts are for use by end users. Users can change the settings that are specific to the unit.
•Administrator: Administrator accounts are for use by administrators to manage the system configuration.
Administrators can change all the settings, including the network settings, in addition to the settings that
can be changed from a User account.
A separate password is assigned to each account.
For details, see Access Levels (IDs and Passwords) in 1.1.6.3 Before Accessing the Web User
Interface.
Notice
•You should manage the passwords carefully, and change them regularly.
1.1.6 Web User Interface Programming
Document Version: 2020-04 Administrator Guide 15

1.1.6.2 Changing the Language for Web User Interface Programming
When accessing the unit via the Web user interface on a PC connected to the same network, various menus
and settings are displayed. You can change the language used for displaying these setting items. Because
the language setting for the Web user interface is not synchronized with those of the unit, you must set the
languages for each independently.
For details, see 3.4.2 Language Settings.
1.1.6.3 Before Accessing the Web User Interface
Recommended Environment
This unit supports the following specifications:
HTTP Version HTTP/1.0 (RFC 1945), HTTP/1.1 (RFC 2616)
Authentication Method Digest
The Web user interface will operate correctly in the following environments:
Operating System Microsoft® Windows® 8, or Windows 10 operating system
Web Browser Windows Internet Explorer 11 web browser, Microsoft Edge, Firefox,
Google™ Chrome™
Language (recommended) English
Opening/Closing the Web Port
To access the Web user interface, you must open the unit’s Web port beforehand. For details, refer to the
Operating Instructions on the Panasonic Web site (→ see Introduction).
Configuring Settings from the Unit
To open the unit’s Web port
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. []/[ ]: "Phone Settings" → /[CENTER]
3. [ ]/[ ]: "Other Option" → /[CENTER]
4. [ ]/[ ]: "Embedded Web" → /[CENTER]
The check mark is displayed in the check box when "Embedded Web" is on.
To close the unit’s Web port
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "Phone Settings" → /[CENTER]
3. [ ]/[ ]: "Other Option" → /[CENTER]
4. [ ]/[ ]: "Embedded Web" → /[CENTER]
The check mark is not displayed in the check box when "Embedded Web" is off.
1.1.6 Web User Interface Programming
16 Administrator Guide Document Version: 2020-04

Configuring Settings from the Web User Interface
To close the unit’s Web port
1. In the Web user interface, click [Web Port Close].
2. Click OK.
Note
•The Web port of the unit will be closed automatically in the following conditions:
–3 consecutive unsuccessful login attempts occur.
•The Web port can be set to stay open continuously, through Configuration file programming (→ see
"HTTPD_PORTOPEN_AUTO" in 4.11 HTTPD/WEB Settings). However, please recognize the possibility
of unauthorized access to the unit by doing so.
Access Levels (IDs and Passwords)
2 accounts with different access privileges are provided for accessing the Web user interface: User and
Administrator. Each account has its own ID and password, which are required to log in to the Web user
interface.
Account Target User ID
(default)
Password
(default) Password Restrictions
User End users user -blank-
(NULL)
•When logged in as User, you can
change the password for the
User account (→ see 3.4.3 User
Password Settings).
•The password can consist of 6 to
64 ASCII characters (case-
sensitive) (→ see Entering
Characters in 1.1.6.4 Accessing
the Web User Interface).
Administrator Network
administrators,
etc.
admin adminpass •When logged in as Administrator,
you can change the password for
both the User and Administrator
accounts (→ see 3.4.4 Admin
Password Settings).
•The password can consist of 6 to
64 ASCII characters (case-
sensitive) (→ see Entering
Characters in 1.1.6.4 Accessing
the Web User Interface).
Notice
•Only one account can be logged in to the Web user interface at a time. If you try to access the Web
user interface while someone is logged in, you will be denied access.
•You cannot log in to the Web user interface even under the same account as someone who is already
logged in.
•The user password is required to change the settings.
•The IDs can be changed through configuration file programming (→ see "ADMIN_ID" and "USER_ID"
in 4.11 HTTPD/WEB Settings).
•If you forget your account IDs or passwords, consult your phone system dealer/service provider.
1.1.6 Web User Interface Programming
Document Version: 2020-04 Administrator Guide 17

1.1.6.4 Accessing the Web User Interface
The unit can be configured from the Web user interface.
To access the Web user interface
1. Open your Web browser, and then enter "http://" followed by the unit’s IP address into the address field
of your browser.
a. When the IP address is 192.168.0.1 (IPv4), access the following URL.
http://192.168.0.1/
b. When the IP address is 2001:db8:1f70::999:de8:7648:6e8 (IPv6), access the following URL. With
IPv6, the IP address is enclosed in square brackets ("[" and "]").
http://[2001:db8:1f70::999:de8:7648:6e8]/
Note
•To determine the unit’s IP address, perform the following operations on the unit:
KX-TPA70/KX-TPA73
[In standby mode]
1. /[CENTER]
2. [ ]/[ ]: "Status" → /[CENTER]
3. [ ]/[ ]: "Base Unit" → /[CENTER]
4. [ ]/[ ]: Check the IP address.
2. For authentication, enter your ID (username) and password, and then click OK.
Notice
•The default ID for the User account is "user", and the default password is blank. The ID cannot be
changed from the Web user interface, but it can be changed through configuration file
programming.
•When you log in as User to the Web user interface for the first time, the [User Password
Settings] screen (→ see 3.4.3 User Password Settings) will be displayed. Enter a new
password, and then perform authentication again with the new password to log in to the Web user
interface.
•The default ID for the Administrator account is "admin", and the default password is "adminpass".
The ID cannot be changed from the Web user interface, but it can be changed through
configuration file programming.
3. The Web user interface window is displayed. Configure the settings for the unit as desired.
4. You can log out from the Web user interface at any time by clicking [Web Port Close].
Controls on the Window
The Web user interface window contains various controls for navigating and configuring settings. The
following figure shows the controls that are displayed on the [Basic Network Settings] screen as an
example:
1.1.6 Web User Interface Programming
18 Administrator Guide Document Version: 2020-04

KX-TGP700
Note
•Actual default values may vary depending on your phone system dealer/service provider.
•When you log in to the Web user interface with the User account, the languages of messages
displayed on the configuration screen may differ depending on the country/area of use.
Tabs
Tabs are the top categories for classifying settings. When you click a tab, the corresponding menu items
and the configuration screen of the first menu item appear. There are 6 tabs for the Administrator
account and 3 tabs for the User account. For details about the account types, see Access Levels (IDs
and Passwords) in this section.
Menu
The menu displays the sub-categories of the selected tab.
Configuration Screen
Clicking a menu displays the corresponding configuration screen, which contains the actual settings,
grouped into sections. For details, see 3.2 Status to 3.7.7 Restart.
Buttons
The following standard buttons are displayed in the Web user interface:
Button Function
Logout Logs out of the Web user interface.
Web Port Close Closes the Web port of the unit and logs you out of the Web user interface
after a confirmation message is displayed.
Save Applies changes and displays a result message (→ see Result Messages in
this section).
1.1.6 Web User Interface Programming
Document Version: 2020-04 Administrator Guide 19

Button Function
Cancel Discards changes. The settings on the current screen will return to the values
they had before being changed.
Refresh Updates the status information displayed on the screen. This button is
displayed in the upper-right area of the [Network Status] and [VoIP Status]
screens.
Entering Characters
In the Web user interface, when specifying a name, message, password, or other text item, you can enter
any of the ASCII characters displayed in the following table with a white background.
However, there are additional limitations for certain types of fields as follows:
•Number field
–You may only enter a sequence of numeric characters.
•IP Address field
–You can enter the IP address using dotted-decimal notation (i.e., "n.n.n.n" where n=0–255).
•FQDN field
–You can enter the IP address using dotted-decimal notation (i.e., "n.n.n.n" where n=0–255).
–With IPv6, the IP address is enclosed in square brackets ("[" and "]").
Example: http://[2001:db8:1f70::999:de8:7648:6e8]/
•Display Name field (→ see [Display Name] in 3.6.3.1 Call Features)
–This is the only field in which you can enter Unicode characters.
Result Messages
When you click [Save] after changing the settings on the current configuration screen, one of the following
messages will appear in the upper-left area of the current configuration screen:
Result Message Description Applicable Screens
Complete The operation has successfully
completed.
All screens except
3.6.7 Export Phonebook
1.1.6 Web User Interface Programming
20 Administrator Guide Document Version: 2020-04