Panasonic TK-AS66-ZEX User manual

We use NSF42 certifi ed
activated carbon.
我們使用 NSF42 認證的活性碳.
COMPONENT / 成分
Activated carbon (APG-05TGA
60/200) manufactured by
Kuraray Co.,Ltd. used in this
product is Tested and Certifi ed
by NSF International against
NSF/ANSI Standard 42 for
material requirements only.
(Check Date (2017.2.1))
本產品使用的活性碳由 Kuraray
Co.,Ltd. 製造的（APG-05TGA
60/200）物料需求由 NSF 國際通
過 NSF/ANSI Standard 42 檢測
和認證。
（檢 查 日期（2 0 17 年 2月1日））
Use properly to economize on electricity 正確使用，節省用電
Model No. TK-AS66-ZEX
Instruction Manual
使用說明書
Alkaline Ionizer Household Use
電解水機 家庭用
Thank you very much for purchasing our Alkaline Ionizer.
感謝您選購 Panasonic 電解水機。
Please read through this manual carefully before using the product to
ensure proper operation.
Be absolutely sure to read the “Safety Precautions” (P. EN3 ~ EN6)
before use to ensure that you will use the product safely.
After
reading the manual, keep it in a safe place along with the warranty in
case you need to refer to it later.
Be absolutely sure to check that the purchase date has been entered
on the warranty.
Please keep in mind that the manufacturer of the product will not be
responsible for any product malfunctioning or accidents resulting from
the improper installation or operation of the product.
使用前請詳閱本說明書，詳閱說明書後再正確使用。特別是「安全注意事項」
（TC3 ~ TC6 頁），請務必在使用前詳細閱讀，以便安全操作。閱讀後請妥
善保管並與保證書放在一起，以備不時之需。
保證書上的「購買日期」請務必填寫。
因安裝錯誤或不正確使用，而造成產品故障或發生事故時，本公司恕不負責。
English
中文（繁體）
TK-AS66-ZEXEn.indb1TK-AS66-ZEXEn.indb1 2017/01/3015:04:102017/01/3015:04:10

EN2
The Alkaline Ionizer
eliminates turbidity and odors, and makes your water tasty.
The Alkaline Ionizer produces alkaline ion water and weak acidic water by electrolysis.
It eliminates the following substances so that the water you drink will be tasty.
13 substances specifi ed by JIS standards
Free residual chlorine, turbidity, total trihalomethane, chloroform, bromodichloromethane,
dibromochloromethane, bromoform, tetrachloroethylene, trichloroethylene,
1,1,1-trichloroethane, CAT, 2-MIB (mold smell), soluble lead
Japan Water Purifi er Association voluntary class 4 substances
Iron (particulate form), Aluminum (neutral), Geosmin (mold smell), Phenols
Contents
Introduction
Safety Precautions ................................ EN3
Operating Precautions .......................... EN7
Supplied Accessories ............................EN8
Checking the Faucet ............................. EN8
Names of the Parts and Steps to Take
Before Operation ................................... EN9
Preparations
Attaching the Bypass Selector ............ EN10
Outside-screwed faucet ........................ EN10
Inside-screwed faucet ............................EN11
Faucet without an aerator ......................EN12
Installing the Alkaline Ionizer ............... EN13
Preparations ...........................................EN13
Checks after installation ........................ EN16
Measuring the pH Level
(Ion Concentration) .............................. EN17
Before Use
Before Operation ................................. EN18
Tips on operating the Alkaline Ionizer ...EN18
Selecting the language of the LCD
displays ..................................................EN19
LCD displays which appear during
operation ................................................EN19
Electrolysis signal ..................................EN19
Operation
Operation............................................. EN20
Using alkaline ion water, weak acidic
water or purifi ed water .......................... EN20
Using the unpurifi ed water
(tap water) ............................................. EN23
Finely adjusting the pH level
(ion concentration) ................................ EN24
For Your Operating Convenience ........ EN25
Measuring the water output volume ...... EN25
Monitoring the water fl ow ...................... EN29
Using the timer ...................................... EN29
Setting mode and check mode ............. EN30
Others
Maintenance ........................................ EN34
Before Replacing the Cartridge ........... EN35
Replacing the Cartridge ...................... EN37
When Moving the Alkaline Ionizer ....... EN38
When not in use for a long time ..........EN39
Automatic Electrode Cleaning ............. EN40
When the Power or Water Supply is
Cut Off .................................................EN40
Q&A ..................................................... EN41
Error Code ...........................................EN44
Troubleshooting ...................................EN45
Optional Accessories .......................... EN49
Specifi cations ...................................... EN50
TK-AS66-ZEXEn.indb2TK-AS66-ZEXEn.indb2 2017/01/3015:04:112017/01/3015:04:11

EN3
Safety Precautions
English
Please make sure to follow these instructions
In order to prevent accidents or injuries to the user, other people, and damage to property, please
follow the instructions below.
The following charts indicate the degree of damage caused by wrong operation.
WARNING
Indicates serious injury
or death.
CAUTION
Indicates risk of injury or
property damage.
The symbols are classifi ed and explained as follows.
(The following are examples of symbols.)
This symbol indicates prohibition. This symbol indicates requirement that
must be followed.
WARNING
Power cord and power plug
Do not damage the power cord or power plug.
(It may cause a fi re or electric shock due to short circuits, faulty insulation, deterioration or other.)
• Using staples ( ) to secure it • Damaging it • Re-working it • Bending it unnaturally
• Twisting it • Pulling it • Positioning it too close to a heating appliance
• Placing heavy objects on top it • Bundling it • Pinching it • Sandwiching it. etc.
When removing the power plug from the power outlet, hold the molded part of the plug rather than
the cord itself, and pull the plug free.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualifi ed persons in order to avoid a hazard.
Do not use in a manner that exceeds the rating of the power outlet or connected
equipment.
(Connecting too many appliances to a power outlet may cause a fi re due to heat generation.)
Do not connect or disconnect the power plug with wet hands.
(It may cause an electric shock.)
Use 220 V - 240 V AC voltage.
Insert the power plug fi rmly.
(It may cause smoking, a fi re or electric shock.)
Do not use a damaged plug or loose power outlet.
Remove the dust or other foreign matter on the power plug periodically.
(If dust or other foreign matter is allowed to build up on the plug, moisture or other factors may lead
to defective insulation which, in turn, may cause a fi re.)
Disconnect the power plug, and wipe it with a dry cloth.
If the Alkaline Ionizer falls into water by accident, disconnect its power plug from
the power outlet, and take the Alkaline Ionizer out of the water.
(Otherwise it may cause an electric shock.)
Please contact an authorized dealer for a check or repair.
Discontinue using the appliance immediately and unplug when abnormality or
breaking down occurs.
(It may cause smoking, a fi re or electric shock.)
<e.g. for abnormality or breaking down>
The lamp indicator is abnormal. (P. EN21)
Abnormal noise generated during operation
The main unit becomes abnormally hot or deformed.
Please contact an authorized dealer for a check or repair.
TK-AS66-ZEXEn.indb3TK-AS66-ZEXEn.indb3 2017/01/3015:04:112017/01/3015:04:11

EN4
Safety Precautions (continued)
WARNING
CAUTION
Disassembly prohibited
Do not disassemble, repair or
remodel the Alkaline Ionizer.
(Doing so can lead to a fi re and/or
electric shocks.)
Please contact an authorized dealer
for a check or repair.
Water supply
Use only water (such as tap water)
which has been approved for
consumption.
(Consuming non-approved water may cause
health problems as this Alkaline Ionizer does
not have sterilization capabilities and cannot
eliminate toxic substances other than those it
can remove (P. EN2).
Existing conditions and health problems
People with kidney disease (users who have renal failure or who have diffi culty in
eliminating potassium from their systems) should not drink alkaline ion water.
(Doing so may cause health problems.)
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance. Keep this instruction manual in a
safe place.
(Otherwise it may cause an accident or health problems.)
People with the following conditions should consult a doctor before drinking
alkaline ion water.
(Otherwise it may cause health problems.)
People who is receiving medical treatment from a doctor
People with health problems or weakened constitution (People who is not feeling well)
People with kidney diseases other than renal failure or potassium elimination
People in the following situations should consult a doctor before applying weak
acidic water to their skin.
(Otherwise it may cause health problems.)
People with sensitive skin
People susceptible to allergic dermatitis
First-time users should consume small quantities (1 to 2 cupfuls) starting at the
“Alkaline Level 1” setting for about two weeks, and then start using the “Alkaline
Level 2” or “Alkaline Level 3” settings when their body has become accustomed to
alkaline ion water.
(Drinking too high a level or too much (3 or more cupfuls) alkaline ion water at the start may cause
health problems.)
TK-AS66-ZEXEn.indb4TK-AS66-ZEXEn.indb4 2017/01/3015:04:112017/01/3015:04:11

EN5
English
CAUTION
Installation location
Do not block the main spout or bend, twist, fl atten,
pull or clamp the hose.
(Doing so may cause water to leak, prevent the output of
water or cause other malfunctioning.)
Do not connect a hose or any other appliances to
main spout, acidic water spout or drain outlet.
(Doing so may cause water leaks or malfunctions.)
Do not use the Alkaline Ionizer if the outlet pipe is
loose.
(Doing so may cause water leaks or damage.)
If it has come loose, screw it in securely.
Do not connect the Alkaline Ionizer to a hot water
supply system which is not equipped with a
directional control check valve (for preventing the
backfl ow of the water).
(Doing so may lead to malfunction in the hot water supply
system.)
Do not connect the Alkaline Ionizer to a main stop
system water boiler (whose construction does not
permit the water to be stopped at the hot water
outlet) [such as an instantaneous water heater].
(Doing so may lead to malfunction in the water boiler.)
Install the main unit on a level surface.
(Failure to do so may cause the main unit to topple over and
possibly cause injury.)
When mounting the main unit on a wall for use, be
absolutely sure to ask your dealer or a contractor
to do the installation work.
(If you try to do the work yourself, the main unit may fall off ,
possibly causing an accident.)
The location where the main unit is to be installed
must be able to support a weight of over 6 kg.
If the installation location does not have enough strength to
support the main unit, the Alkaline Ionizer may fall, resulting
in an accident and kitchen damage.
Maintenance
Do not splash water
or wash the main
unit.
(It may cause an
electrical leakage,
electric shock or
malfunction.)
Accidental ingestion
Do not leave
the supplied
accessories within
reach of infants or
toddlers.
(Doing so may result
in accessories being
swallowed by mistake.)
Consult a doctor
immediately if you
suspect that an
accessory has been
swallowed.
Do not allow infants
and children to play
with packaging
material.
(It may cause
suff ocation.)
TK-AS66-ZEXEn.indb5TK-AS66-ZEXEn.indb5 2017/01/3015:04:112017/01/3015:04:11

EN6
Safety Precautions (continued)
CAUTION
Non-consumable alkaline ion water, applications
 Do not drink the following kinds of water:
(Doing so may cause health problems.)
Weak acidic or acidic water
Water which comes out of the drain outlet
Water which comes out of the main spout in
the “Preparation time” status or during the
automatic cleaning of the electrodes.

Water which contains pH test liquid.
Do not directly consume water whose
pH level exceeds 10.
(Doing so may cause health problems.)
 Consuming water which has a pH level of
around 9.5 “Alkaline Level 3” (Drinking water
in daily life) is recommended. Keep the
general amount of water consumed daily at
around 0.5 liter to 1 liter.
 Do not take medicine with alkaline ion water.
(Doing so may cause health problems.)
Do not use alkaline ion water, acidic
water, or purifi ed water for the care of
fi sh or other pets.
(The environment may
change as a result, and
the fi sh, etc. may die.)
 Do not use aluminum
containers that
do not stand up to
alkalis or copper
containers that do
not stand up to acids.
(Doing so may cause
discoloration of the
containers or damage them.)
 When starting to use the Alkaline Ionizer, drain
out the water which has collected inside.
(Otherwise it may cause health problems.)
When starting use
every day
Run about 0.6 liter (about
15 seconds) of water
through the Alkaline Ionizer.
When the Alkaline
Ionizer has not been
used for 2 or more days
Run about 8 liters (about 3
minutes) of water through
the Alkaline Ionizer.
Aluminum or copper
containers
Storing alkaline ion water and purifi ed water
 Use alkaline ion water or purifi ed water
immediately after it is produced, or
when storing it for future consumption,
pour into a clean sealed container, and
consume it within 1 day if it is kept at
room temperature or within 2 days if it
is kept in the refrigerator.
(The Alkaline Ionizer removes sterilizers
(such as chlorine) so the water may go bad
over time, possibly causing health problems.)
If feeling unwell
 If you have drunk alkaline ion water
and do not feel well as a result, or if
the symptoms do not improve after
continued use, stop drinking the
water and consult a doctor.
(Otherwise it may cause health problems.)
 If you have applied weak acidic water
to your skin and you experience skin
problems, stop use immediately, and
consult a doctor.
(Otherwise it may cause health problems.)
Hot water
 Do not allow water above 60 °C in temperature
to pass through the Alkaline Ionizer.
(It may cause a burn.)
pH test liquid
Do not bring the pH test liquid
near a naked fl ame.
(Doing so may cause it to ignite,
causing a fi re.)
Do not drink the pH test liquid
or the water containing the test
liquid or put in your eyes.
(Keep these liquids away from children.)
(Doing so may cause health problems.)
 If the reagent or water containing it has
been accidentally swallowed, drink copious
amounts of water; if it has made contact
with your eyes, rinse thoroughly with clean
water and, in either case, consult a doctor.
 Place the cap on the test liquid container, and
keep it out of the reach of infants and toddlers.
TK-AS66-ZEXEn.indb6TK-AS66-ZEXEn.indb6 2017/01/3015:04:112017/01/3015:04:11

EN7
Operating Precautions
English
Do not run the following types of water
through the Alkaline Ionizer.
(Doing so may shorten the service life of the
cartridge.)
Water which is very turbid
Water containing a great deal of red rust
Do not run well water containing sea water
or other salt content (from wells near
coastal area) through the Alkaline Ionizer.
(Doing so may cause malfunction.)
When using the Alkaline Ionizer in areas
where the water is very hard*
Once a day, run weak acidic water through the
Alkaline Ionizer for about a minute before use
(otherwise calcium will build up on the main
spout and along the water lines, hindering the
passage of the water).
*: In areas where the water is very hard, soap will
not lather easily and white deposits (calcium) will
build up in kettles and pans.
Depending on the region and water
quality, it may not be possible to acquire
the designated pH level.
Usage
Do not place this product upside down.
(Doing so may cause that lead to malfunction.)
Do not connect the Alkaline Ionizer to a
hot water-only faucet.
(Doing so may cause malfunction.)
The table below shows the temperatures
of water that can be used. Use water at
these temperatures.
(Failure to do so may cause damage or adhesion
to the cartridge, resulting in part of the total
trihalomethane being discharged.)
Position of bypass selector Water temperature
Purifi ed Under 35 °C
Unpurifi ed/Shower Under 80 °C
Do not lift the main unit by taking hold
of the outlet pipe, or forcefully move the
main unit.
(Doing so may cause damage.)
Do not continuously produce alkaline ion
water or weak acidic water beyond the
time spans given in the table below.
If water is produced for longer periods than
the ones shown below, the “U27” error code
(P. EN44) will appear on the LCD display, and
electrolysis will be suspended.
Alkaline 4
(Strongly Alkaline) Approx. 10 minutes
Stronger for Alkaline 3 Approx. 10 minutes
Standard or Milder for
Alkaline 3 Approx. 30 minutes
Alkaline 2 Approx. 30 minutes
Alkaline 1 Approx. 30 minutes
Weak Acidic Approx. 10 minutes
Installation location
Do not install the Alkaline Ionizer in any of
the following locations.
Near hot areas such as heating appliances
(above 60 °C)
(Doing so may cause it to become deformed.)
In an area in direct sunlight or where it may
be exposed to wind and rain
(Doing so may cause incorrect operation or
malfunctions.)
Where it may freeze
(Doing so may cause cracking in the water pipes
or cartridge.)
Where it may be covered with oil
(Doing so may cause cracking in the case.)
In a bathroom or where the Alkaline Ionizer
will be exposed to water or steam
(Doing so may cause incorrect operation or
malfunctions.)
In areas lower than the kitchen counter
(such as the fl oor)
(Doing so may cause insuffi cient draining of
cleaning water through the pipes.)
Near radios
(Doing so may generate static in the radio.)
Do not use a hose or other commercially
available product to extend the water
outlet.
(Doing so may cause malfunction.)
Water supply
TK-AS66-ZEXEn.indb7TK-AS66-ZEXEn.indb7 2017/01/3015:04:122017/01/3015:04:12

EN8
Supplied Accessories
Checking the Faucet
Note
Faucet with a fl aring end
• Water faucet which can
attach the Alkaline Ionizer
using options.
Diameter of faucet end:
24 ~ 32 mm
OPTION
Large-diameter Faucet Fitting
Model No.: P-06JRC (P. EN49)
Before using this unit, check that the following supplied accessories are accounted for. If any are
missing, contact your dealer.
For Use in Attaching
the Bypass Selector
For Use in Installing
the Main Unit Consumables
Bypass Selector
Installation Adaptor
(with 4 screws)
Bushing (with gasket)
Acidic Water Stand
(with drain outlet
and suction disc)
With gasket
Outlet Pipe
Mounting Disc
Hose Strap
Suction Disc
(for acidic water and
drain hoses)
pH Test Kit
Water faucet which cannot install the Alkaline Ionizer
• Faucet without a metal
lip end
• Faucet with an end of
10 mm or less
• Shower nozzle • Faucet with sensor
Plastic or other
material
10 mm or less
TK-AS66-ZEXEn.indb8TK-AS66-ZEXEn.indb8 2017/01/3015:04:122017/01/3015:04:12

EN9
Names of the Parts and Steps to Take Before Operation
Outlet pipe (length: approx. 45 cm)
Control panel
(P. EN30)
LCD display
Main unit
Water supply hose
(length: approx. 90 cm)
Faucet
(not included)
Hose strap
Bypass
selector
Drain outlet
Acidic water and drain hoses
(length: approx. 60 cm)
Suction
disc
Water quality selector
buttons (P. EN20)
Power plug
Power cord
(length: approx. 3 m)
Acidic water stand
(with drain outlet)
Acidic water spout
Acidic water will come out while the Alkaline Ionizer is producing
alkaline ion water. (Use it to wash dishes, vegetables, etc.)
Main spout
English
1Checking the faucet
(P. EN8)
2Attaching the bypass selector
(P. EN10 ~ EN12)
3Installing the Alkaline Ionizer and
plug in.
(P. EN13 ~ EN15)
4
Check after installation (P. EN16)
Run alkaline ion water through the
Alkaline Ionizer for about 3 to 4 minutes
to expel the air inside the main unit.
“Preparation time” blinks for about 20
seconds on the LCD display.
Steps to take before operation
5Measuring the pH level
(ion concentration)
(P. EN17)
6Selecting the language of the LCD
displays
(P. EN19)
Operation (P. EN20 ~ EN22)
TK-AS66-ZEXEn.indb9TK-AS66-ZEXEn.indb9 2017/01/3015:04:122017/01/3015:04:12

EN10
Attaching the Bypass Selector
Keep all parts that are not used during installation, as they may be needed later if the unit is moved or the faucet
is changed.
Outside-screwed faucet
• Water faucet which can attach the Alkaline
Ionizer without an accessory.
1Remove the mounting nut and
adaptor.
When the fi lter or gasket washer (made
of metal) drops off , please return to the
original position (P. EN34).
Make sure any foreign matter is not
attached on the end of the faucet and
gasket inside of the bypass selector.
Mounting nut
Adaptor
Gasket
Do not remove the gasket washer
inside the bypass selector.
If it is moved, return to the
original position.
Make sure foreign matter is
not attached to the fi lter and
the gasket is not inclined.
Filter
Gasket
washer
2Attach the mounting nut and
adaptor.
1
2
Mounting nut
Gasket
Adaptor
3Attach the bypass selector and
tighten the mounting unit until
the bypass selector does not
turn.
Do not use any tools. (This may
damage the mounting nut.)
Make sure the bypass selector is
not inclined.
1
2
Bypass selector Mounting nut
Aerator (not used)
Do not use the
removed aerator.
TK-AS66-ZEXEn.indb10TK-AS66-ZEXEn.indb10 2017/01/3015:04:122017/01/3015:04:12

EN11
English
Inside-screwed faucet
• Water faucet which can attach the Alkaline
Ionizer with an accessory.
Aerator (not used)
Do not use the removed aerator.
1Remove the mounting nut and
adaptor.
When the fi lter or gasket washer (made
of metal) drops off , please return to the
original position (P. EN34).
Make sure any foreign matter is not
attached on the end of the faucet and
gasket inside of the bypass selector.
Mounting nut
Adaptor
Gasket
Do not remove the gasket washer
inside the bypass selector.
If it is moved, return to the
original position.
Make sure foreign matter is
not attached to the fi lter and
the gasket is not inclined.
Filter
Gasket
washer
2Screw in the bushing. Insert into
the adaptor. Bushing (Accessory)
Gasket
Adaptor
3Attach the mounting nut and
adaptor.
The adaptor should be screwed on
straight. Screwing it on tilted may
strip the threads, resulting in water
leaks.
1
2
Mounting nut
Gasket
Adaptor
4Attach the bypass selector and
tighten the mounting unit until
the bypass selector does not
turn.
Do not use any tools. (This may
damage the mounting nut.)
Make sure the bypass selector is
not inclined. Mounting nut
Bypass selector
TK-AS66-ZEXEn.indb11TK-AS66-ZEXEn.indb11 2017/01/3015:04:132017/01/3015:04:13

EN12
Attaching the Bypass Selector (continued)
Faucet without an aerator
• Water faucet which can attach the
Alkaline Ionizer with accessory.




Bulge
 more than 10 mm
 13 mm or more, less than 24 mm
1Remove the mounting nut and
adaptor.
When the fi lter or gasket washer (made
of metal) drops off , please return to the
original position (P. EN34).
Make sure any foreign matter is not
attached on the end of the faucet and
gasket inside of the bypass selector.
Mounting nut
Adaptor
Gasket
Do not remove the gasket washer
inside the bypass selector.
If it is moved, return to the
original position.
Make sure foreign matter is
not attached to the fi lter and
the gasket is not inclined.
Filter
Gasket
washer
2Insert the installation adaptor,
and tighten it with the mounting
nut.
Mounting nut
Remove the screws
(4 pcs.)
Installation adaptor
(Accessory)
3Tighten the 4 screws temporarily
and loosen the mounting nut to
leave a 3 ~ 4 mm gap.
Mounting nut
3 ~ 4 mm
Screws
(4 pcs.)
4
Push the bypass selector against the faucet
and install the 4 screws as shown below.
Top view


 Water faucet
 Installation adaptor
 Screws
Water faucet
Bypass selector
5
Tighten the mounting unit until
the bypass selector does not turn.
Do not use any tools. (This may
damage the mounting nut.)
Make sure the bypass selector is
not inclined.
Mounting nut
TK-AS66-ZEXEn.indb12TK-AS66-ZEXEn.indb12 2017/01/3015:04:132017/01/3015:04:13

EN13
Installing the Alkaline Ionizer
English
Preparations
1Choose a stable, level surface.
21 cm
or more
13 cm
or more
2Extend the power cord and hose in the manner that best suits the
location where the unit is installed.
Do not fl atten or bend the cord or hose.
Bottom of the unit
When extending the cord and hose from the left
Spring (to prevent
the hose from being
bent)
Wedge the hoses into this cutout
Condensation water outlet Cutout
Pulling the drain hose slightly toward
the inside as shown in the fi gure takes
up any slack between this hose and
the acidic water hose
Water supply hose
Front panel of the main unit
When extending the cord and hose from the right
Condensation water outlet
Front panel of the unit
Position the acidic water hose so that it
will not go over the condensation water
outlet (since the unit will be unstable
when it is placed right side up).
TK-AS66-ZEXEn.indb13TK-AS66-ZEXEn.indb13 2017/01/3015:04:132017/01/3015:04:13

EN14
Installing the Alkaline Ionizer (continued)



Remove the hose fastening nut from the bypass
selector, and pass the hose through the nut.
Insert the water supply
hose into the bypass
selector as far as it will go.
Tighten up the hose fastening nut securely.
1After completing the preparations,
connect the water supply hose.
4Install the acidic water stand.
2
Secure the water supply
hose (using the hose strap).
 Insert the acidic water and drain hoses securely.
 Attach the stand to the side of the sink.
(If the suction disc slips off , stick the
mounting disc onto the side of the sink.)
Connect the hoses as instructed on the label.
Do not place a waste container or other such
objects underneath the acidic water stand.
The acidic water spout must be below the level
of the bottom of the unit and the diff erence
in height between the main spout and acidic
water spout must be greater than 10 cm and
less than 50 cm (so that the appropriate pH
level (ion concentration) is achieved).
Mounting
disc
Adhere to the
side of the sink.
Acidic
water spout Bottom
of unit
Height diff erence
Main spout
Acidic water and
drain hoses
Acidic water
stand
Light gray
Dark gray
Label
 Hold here  Detach here
 How to remove the acidic water stand
Do not use any tools for this assembly (since the
hose fastening nut may be damaged).
OK NG
Gap
Installation position
TK-AS66-ZEXEn.indb14TK-AS66-ZEXEn.indb14 2017/01/3015:04:142017/01/3015:04:14

EN15
English
Note
If the hose is too long, it is recommended
that you cut it to the proper length (cut it
straight down).
Immediately after the Alkaline Ionizer has
been installed, “Preparation time” blinks
for about 20 seconds on the LCD display
when water is run through the Alkaline
Ionizer. (P. EN9)
The language of the LCD displays can be
selected from English or Chinese.
(P. EN19)
Important
The power plug is normally kept connected
to the power outlet (to keep the automatic
electrode cleaning function working).
3Screw in the outlet pipe until it is secured fi rmly.
Do not use any tools for this assembly (since the pipe may be damaged).
Ensure that the gasket is not twisted (since this may cause the water to leak).
Do not lift the unit by taking hold of the outlet pipe (otherwise damage may
result).
Secure the hoses so that they will not
move out of place.
The buzzer sounds, about 15 seconds
later the LCD display lights up in blue,
and “鹼性1（飲用初期）” appears on the
display
The Alkaline Ionizer’s power consumption
is 1 W even in the standby status.
LCD display
Gasket
5Secure the acidic water
and drain hoses using the
suction disc. 6
Connect the power plug to
the power outlet (AC 220 V - 240 V).
TK-AS66-ZEXEn.indb15TK-AS66-ZEXEn.indb15 2017/01/3015:04:142017/01/3015:04:14

EN16
Installing the Alkaline Ionizer (continued)
Checks after installation
After installing the Alkaline Ionizer, run alkaline ion water through the unit for about 3 or 4 minutes to
expel the air inside the main unit.
Check item Trouble inspection location and remedial action
Reference
page
Is water coming out of the
main spout?
Main spout
Is the water supply hose bent or fl attened.
If it is, straighten it out.
EN13
~
EN15
Is water coming out of the
acidic water spout when
alkaline ion water has passed
through the Alkaline Ionizer?
Acidic water spout
Are the acidic water and drain hoses bent or fl attened?
If they are, straighten them out.
Have the acidic water and drain hoses been connected properly.
If not, check their connections to the acidic water stand.
EN13
~
EN15
Does “Reduce fl ow” appear on the LCD display?
If so, gradually reduce the fl ow at the faucet until the display
is cleared.
If water coming out of the acidic water spout is interrupted,
increase the height diff erence of the main spout and acidic
water spout.
EN22
Is any water leaking
from where the bypass
selector is connected?
Has the bypass selector been installed securely on the faucet?
Check again the instructions for “Attaching the Bypass
Selector”, and install it securely.
Have the parts inside the bypass selector been inserted
properly?
If not, install them properly.
EN10
~
EN12
Are there any cracks at the end of the faucet (in the insulating
cap, for instance)?
Consult a plumber.
–
Is there any water leaking
from where the water supply
hose is connected? Has the water supply hose been attached securely to the
bypass selector?
Insert it as far as it will go, and use the hose fastening nut to
secure it.
EN14
Is there any water leaking
from where the outlet pipe
is connected? Has the outlet pipe been attached securely to the unit?
Insert it securely as far as it will go.
Is the gasket installed on the outlet pipe or is it twisted?
Install the gasket properly.
EN15
Is water leaking from the faucet?
Is the gasket on the faucet old?
Consult a plumber.
Are there any cracks in the faucet (in the insulating cap, for
instance)?
Consult a plumber.
–
TK-AS66-ZEXEn.indb16TK-AS66-ZEXEn.indb16 2017/01/3015:04:142017/01/3015:04:14

EN17
Measuring the pH Level (Ion Concentration)
English
After the Alkaline Ionizer has been installed or after it has not
been used for a prolonged period (generally, a week or more),
be absolutely sure to measure the pH level, and check that it
is within the “pH standard” before using the Alkaline Ionizer.
Remember to measure the pH level periodically
(at least once a month).
What is the pH level (ion concentration)?
The pH level indicates the degree of alkalinity, neutrality or acidity of
water (aqueous solutions), and stands for “hydrogen ion exponent.”
Hp
Neutrality
Acidic Alkaline
Strong Mild Mild Strong
789 10 456
Acidic Alkaline
Strong Mild Mild Strong
Neutrality
pH
What to have ready: pH test kit (supplied accessory)
Procedure for measurement
1Put 2 drops of pH test liquid in to the
test tube.
(The pH cannot be determined accurately any amount
other than 2 drops.)
pH test liquid
Test tube
2Run alkaline ion water or weak acidic water for approximately
10 seconds, then keep the sample water in a cup.
(In order to obtain a stable pH value.)
3Put the sample water into the test tube.
Fill up to the line.
4Under the enough light,
compare the result with the
pH Chart.
pH Chart pH standard
Alkaline 4 (Strongly Alkaline) 9.5 ~ 10.5
Alkaline 3 9.0 ~ 10.0
Alkaline 2 8.5 ~ 9.5
Alkaline 1 8.0 ~ 9.0
Weak Acidic 5.0 ~ 6.5
Important
 The color of the test water will change as time passes. Compare its pH level against the pH Chart right away.
 The pH level cannot be measured accurately using litmus paper available on the market. Be absolutely sure to measure it using the pH test kit.
To dispose of the pH test liquid, dilute it with water before pouring it down the drain.

The pH test liquid and pH Chart will become discolored if they are exposed to sunlight so store them in a dark place.
Note
The pH test kit is for measuring the rough pH level.
The main components of the reagent are ethanol, methyl red, bromothymol blue and phenolphthalein.
Depending on the water quality, the water treated by the Alkaline Ionizer may not be within the pH
standard range or the alkaline ion water may not be alkaline (a liquid which appears blue or dark
blue may change to a green or yellow color). If this is the case, take the following action.
Use “pH Fine Adjustment” to set the alkalinity or slight acidity to “Stronger”. (P. EN24)
In addition, when the unpurifi ed water is measured, the color of the test water may diff er from
what is on the pH Chart (due to the eff ects of carbonic acid or other components in the water).

If the pH level is high, change the water quality to weak alkaline or mix the water with purifi ed water before using it.
 When the cartridge is new (about a week old), the pH level may be somewhat higher: this is normal and does not indicate any trouble.
TK-AS66-ZEXEn.indb17TK-AS66-ZEXEn.indb17 2017/01/3015:04:152017/01/3015:04:15

EN18
Before Operation
Tips on operating the Alkaline Ionizer (using it to suit the intended application)
Alkaline ion water:
The pH level of alkaline ion water increases by about 0.5 per setting in the following sequence: Alkaline
1 → Alkaline 2 → Alkaline 3 → Alkaline 4 (Strongly Alkaline). In these instructions, “Alkalines 1 to 3” are
collectively referred to as “Alkaline”.
Keep the amount of water consumed daily at around 0.5 liter to 1 liter at the “Alkaline 3”.
Application pH standard
Removing
astringency,
boiling vegetables
When removing the astringency from burdock and
spinach, etc. (Do not drink this water.) 9.5 ~ 10.5
Drinking water in
daily life
For coff ee, tea, boiling or stewing food,
cooking food in pots at the table, soups 9.0 ~ 10.0
Drinking water for
Experienced user When cooking rice 8.5 ~ 9.5
Drinking water for
new user
When starting to drink alkaline ion water
(fi rst two weeks or so) 8.0 ~ 9.0
Purifi ed water:
This is fi ltered water which contains
minimal impurities.
Applications Taking medicine or
making baby formula, etc.
The water has not been subjected to
electrolysis.
Weak acidic water:
The mild acidity of this water is close
to the acidity of the human skin.
Applications Washing the face
pH standard 5.0 to 6.5
Acidic water:
 When is pressed and the fl ow is
reduced at the faucet, acidic water with a pH
level of 3 or so comes out of the acidic water
spout.
(For removing tea stains from tableware,
odors left behind by cooking fi sh dishes, etc.)
pH standard 2.8 to 3.5*
*: When the pH3 water quality indicator lights
up.
TK-AS66-ZEXEn.indb18TK-AS66-ZEXEn.indb18 2017/01/3015:04:162017/01/3015:04:16

EN19
English
Selecting the language of the LCD displays
The language of the LCD displays can be selected from English or Chinese. The default setting is Chinese.
Turn off the faucet, and press down until the buzzer beeps four times (about 3 seconds).
When the button is pressed again for about 3 seconds, the
language of the LCD displays returns to Chinese.
Note
The steps to switch the displays to English cannot be taken while water is running through the Alkaline Ionizer
or while the setting mode or check mode is established.
Even if the displays are switched to English, displays in the setting or check mode will remain in Chinese.
LCD displays which appear during operation
Characters and pictographs indicating the application are displayed alternately.
e.g.) When the “Alkaline 1” (Drinking water for new user) is selected
At intervals of
approx. 2 seconds
pH fi ne adjustment setting
displayed here (P. EN24)
 “Electrolysis On” is displayed while the Alkaline Ionizer
is making alkaline ion water or weak acidic water.
During use Standby status
The remaining cartridge
life is displayed
(P. EN35).
e.g.)
When the
faucet is
turned off ...
Note
 The LCD displays will be cleared about 30 to 45 seconds after a button has been operated or after the faucet has been turned
off (in order to conserve power). They light up when another button is operated or the water fl ows to the Alkaline Ionizer.
 When the water fl ow has dropped (to less than 1.0 liter or so a minute), the remaining cartridge life is displayed even while water
is running through the Alkaline Ionizer. In a case like this, the water is not electrolyzed (no electrolysis and no water treatment).
Electrolysis signal
While “Electrolysis On” is displayed, a display is provided to indicate roughly the electrolytic strength (amount of power
used for the electrolysis). It does not appear while the water is turned off or while purifi ed water is being produced.
The electrolytic strength changes (in 8 steps) depending on the water quality selector buttons and water fl ow
(amount of water being electrolyzed) used.
Electrolysis On
Lighted
 Indicates the
electrolytic strength.
Lights one block at a
time from bottom to top.
During preparations
Lights one block
at a time from
the top and
bottom toward
the center.
 When the “Reduce fl ow” message
appears on the LCD display
Blink
To turn off the electrolysis signal
Refer to “How to set” (P. EN32), and set “Electrolysis Signal” to “OFF”.
TK-AS66-ZEXEn.indb19TK-AS66-ZEXEn.indb19 2017/01/3015:04:162017/01/3015:04:16

EN20
Operation
2
1
3
Continue lamp
LCD
display
Water quality indicators
Acidic water
spout
Drain outlet Electrolysis signal (P. EN19)
1Set the bypass
selector to
“Purifi ed”. 3Open the
faucet.
2Press the water
quality selector button
corresponding to the type of
water required.
The buzzer beeps, and the water
quality indicator and LCD
display light.
“Preparation time”
now appears on the
display.
Water quality
selector button Application LCD display
color
When removing the astringency
from food or boiling vegetables Orange
Drinking water in daily life
Blue
Drinking water for Experienced
user
Drinking water for new user
Medicine, milk Green
Washing the face Pink
Using alkaline ion water, weak acidic water or purifi ed water
TK-AS66-ZEXEn.indb20TK-AS66-ZEXEn.indb20 2017/01/3015:04:162017/01/3015:04:16