Panasonic EY-0214 User manual

Panasonic x
Battery charger
Operating Instructions
Model No: EY0214
Before
operating
this
unit,
please
read
these
instructions
completely
and
save
this
manual
for
future
use.
SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY
INSTRUCTIONS
» SAVE THESE IN-
TRUCTIONS m
manual contains important safety and
operating Instructions for battery
charger EY0214.
2) Before using battery charger, read ail
instructions and cautionary markings
on (1) battery charger, (2) battery
pack.
3) CAUTION -To reduce the risk
of injury, charge only Battery Pack as
shown below.
EY9103, EY9101, EY9001, EY9006,
EY9180, EY9080, EY9182, EY9086,
EY9065, EY9106, EY9107, EY9136,
EY9117, EY9230, EY9200, EY9108,
EY9210
Other types of batteries may burst
causing personal injury and damage.
4) Do not expose charger to rain or
snow.
5) To reduce risk of damaging the electric
plug and cord, pull by plug rather than
cord when disconnecting charger.
6) Make sure cord is located so that it will
not be stepped on, tripped over, or
otherwise subjected to damage or
stress.
7) An extension cord should not be
used unless absolutely necessary.
Use of Improper extension cord could
result in a risk of fire and electric
shock. If extension cord must be
used, make sure:
a. that pins on plug of extension cord
are the same number, size and
shape as those of plug on charger.
b. that extension cord is properly
wired and in good electrical
condition.
c. that wire size is targe enough for
ampere rating of charger as specified
below.
RECOMMENDED MINIMUM AWG SIZE OF
EXTENSION CORD:
BATTERY CHARGERS
than
S FOR
AC Input Rating. Amperes AWG Size of Cord
Equalto or Butless Length ol Cord, Feet
25 650 100 150
16
greater than
0 2 18 18 18
8) Do not operate charger with
damaged cord or plug—replace them
immediately.
9) Do not operate charger if it has
received a sharp blow, been
dropped, or otherwise damaged in
any way; take it to a qualified
serviceman.
10) Do not disassemble charger; take it
to a qualified serviceman when
service or repair is required. Incorrect
reassembly may result in a risk of
electric shock or fire.
11) To reduce the risk of electric shock,
unplug charger from outlet before
attempting any maintenance or
cleaning.
12) The charger and battery pack are .
specifically designed to work
together. Do not attempt to charge
any other cordless tool or battery
pack with this charger.
13) Do not attempt to charge the battery
pack with any other charger.
14) Do not attempt to disassemble the
battery pack housing.
15) Do not store the tool and battery
pack in tocations where the
temperature may reach or exceed
122°F (50°C) (such as a metal tool
shed, or a car in the i
can lead to deterioration of the
storage battery.
16) Do not charge battery pack when the
temperature is BELOW 32°F (0°C) or
ABOVE 104°F (40°C). This is very
important.

17) Do not incinerate the battery pack. It
can explode in a fire.
18) Avoid dangerous environment. Do not
use charger in damp or wet locations.
19) The charger is designed to operate
on standard household electrical
power only. Do not attempt to use it
on any other voltage!
20) Do not abuse cord. Never carry
charger by cord or yank it to
disconnect from outlet. Keep cord
away from heat, oil and sharp edges.
21) Charge the battery pack in a well
ventilated place, do not cover the
charger and battery pack with a cloth,
etc., while charging.
22) Use of an attachment not
recommended may result in a risk of
fire, electric shock, or injury to
persons.
23) Do not short the battery pack. A
battery short can cause a large
current flow, over heating and bums.
24) NOTE: If the supply cord of this
appliance is damaged, It must only
be replaced by a repair shop
appointed by the manufacturer,
because special purpose tools are
required.
25)TO REDUCE THE RISK OF
ELECTRIC SHOCK, THIS
APPLIANCE HAS A POLARIZED
PLUG (ONE BLADE IS WIDER THAN
THE OTHER).
This plug will fit in a polarized outlet
only one way. If the plug does not fit
fully in the outlet, reverse the plug. if
it still does not fit, contact a qualified
electrician to install the proper outlet.
Do not change the plug in any way.
e Changes or modifications not
expressly MATSUSHITA
ELECTRIC WORKS, LTD. could void
the user's authority to operate the
equipment.
` To power source
CHARGING
THE BATTERY
NOTE: When you charge the battery pack for
the first time, or after prolonged
storage, charge it for about 24 hours to
bring the batteries up to full capacity.
1. Plug the charger into the power
source.
NOTE: Sparks may be produced when the plug
is inserted into the AC power supply, but
this Is not a problem in terms of safety.
2. Open the cap and insert the battery
pack firmly into the charger.
y
e When charging, cooling fan in the
charger functions to cool down the
battery pack, and the sound of fan
can be heard. This is normal. If this
sound cannot be heard, It is a
malfunction. Stop charging
immediately and consult an
authorized dealer.
3. During charging, the charging lamp
will be lit.
When charging is completed, an
internal electronic switch will
automatically be triggered to prevent
overcharging.
e Charging will not start if the battery
ack is warm (for example,
immediately after heavy-duty
ronan standby | itl be Mi
orange standby lamp wi t
until the cools down. Ñ
battery .
will then begin automatically.
4. When charging is completed, the
charging tamp will start flashing
rapidly.
5. When the battery pack has not been
used for a long time, the charg
starts tlashing slowly to indicate
protective charg ng: Protective charging
takes longer to fully charge the battery
pack, than the standard charging time.
(Max. charging time is approx. 90
minutes.)

e If a fully charged battery pack is
inserted into the charger again, the
charging lamp may light up and then
flash siowly. After several minutes,
the charging lamp may flash quickly
to indicate the charging is
6. If the charging lamp does not light
immediately after the charger is
plugged in, or if after the standard
charging time the lamp does not go
off, consult an authorized dealer.
Note: © When charging a cool battery pack (below
5°C) in a wamm place, leave the battery
pack at the place and wait for more than
one hour to warm up the battery to the
level of the ambient temperature. (Battery
pack may not be fully charged.)
e Cool down the charger when
charging more than two battery
packs consecutively.
e Do not insert your fingers into
contact hole, when holding charger
or any other occasions.
CAUTION: + Do not use power source from
an engine generator.
© Do not cover vent holes on the
charger and the battery pack.
LAMP INDICATIONS
Flashing
Lit
ecoeoenneees
Charger is plugged into a wall outlet.
Ready to charge.
Now charging
Charging is completed
Protective charging
Battery pack is warm. Charging will begin
when temperature of battery drops.
Charging is not possible. Clogged with
ow = ome OD dust or matfunction of the battery pack.
Flashing
SPECIFICATIONS
0.97kg, (2.14 ibs)
Charging time 24V
EY9001 | EY9080} EY9065
EY9006|EY9086
EY9101/EY9180
— RISER) — [reason
Standard Charging Time
PANASONIC
HOME
&
CC
&
COMMERCIAL
PRODUCTS
COMPANY
Way, Secaucus, New J
EY981002141 H1204
Printed in Japan