Panasonic WVLZ6115 - ZOOM LENS User manual

15X Zoom Lens
WV-LZ61/15
Before attempting to connect or operate this product,
please read these instructions completely.
FRANÇAIS ENGLISH

- 1 -
Note: Clean the lens face with care.
Do not clean the lens with strong or abra-
sive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
●Prepare the zoom and focus cable
1. Remove the connector terminal from the
connector supplied by pushing the lock pin.
Push here to remove
2. Solder the cable to the pins of the supplied
connector according to the diagram shown
below.
The maximum cable length is also as shown
below.
Clamp
View from solder side
Solder
1 : Common
2 : Not used
3 : Focus
4 : Zoom
1432
#20
(0.52 mm2)
m70
Copper Wire Gauge Maximum Cable Length
ft 225
#18
(0.83 mm2)
m 115
ft 375
#16
(0.131 mm2)
m 165
ft 550
#14
(2.08 mm2)
m 285
ft 930

Operating
current sup-
plied from
receiver or
controller
- 2 -
Notes:
• Lens control is disabled when the lens is
connected to a receiver or controller of less
than 12 V 50 mA or 9 V 65 mA.
• If the lens is connected to a receiver or con-
troller of a lower current rating when the
voltage selector is at 6V, a time lag may
occur to activate the lens after pressing the
controller button.
• If this lens is used in a Panasonic WV-
RC100 or WV-RC150 receiver with the lens
voltage selection switch set to the LOW
position and the lens voltage fine control set
to the default position, the zoom may not
function.
In such a case, set the lens voltage fine
control of the receiver to the maximum posi-
tion or the lens voltage selection switch to
the HIGH position (lens voltage selector
also set to 12 V) before using the lens.
ENGLISH
●Voltage Selector Setting
Set the Voltage Selector located on the rear of
the lens, to either 6V or 12V, according to system
requirements.
Switch position
Position for
operating
any
Panasonic
products
6 V, 120 mA 12 V, 50 mA
Applicable
receiver or
controller
Made by
Panasonic Others AMERICAN
DYNAMICS
PELCO, Molynx
Building Block
Video, etc.
12 V 50 mA or
9 V 65 mA or
more is neces-
sary for operat-
ing the above

- 3 -
●Mount the Lens
1. Set the ALC selector on the camera to DC
position.
ALC
DC VIDEO
ELC
ELC
DC
ALC
VIDEO
2. Mount the lens by turning it clockwise on the
lens mount of the camera.
ALC Lens Connector
ALC Lens Cable (4 pin)
3. Connect the ALC cable to the Auto Iris Lens
Connector on the side of the camera.
4. Connect the zoom and focus control cable
to the external equipment, such as a con-
troller or receiver.

- 4 -
Flange-back
Adjusting Ring
Screws
●Flange-back Adjustment
1. Loosen the screws on the flange-back
adjusting ring of the camera.
2. Set the lens at wide position.
3. Shoot an object more than 10 meters (30
feet) away, then turn the flange-back ring of
the camera to bring the object into focus.
4. Set the lens at tele position.
5. Adjust the focus to bring the object into
focus.
6. Zoom out the object, then turn the flange-
back adjusting ring again to bring the object
into focus.
7. Repeat the procedures 4 to 6 to be in focus
over the zoom range of the lens.
8. Tighten the screws on the flange-back
adjusting ring.

- 5 -
SPECIFICATIONS
Image Size: φ6 mm [4.8(H) x 3.6(V) mm]
Focal Length: 6 - 90 mm
Maximum Aperture Ratio: 1 : 1.6 (wide) - 1 : 2.6 (tele)
Iris Range: F1.6 - F176, Close
Angular Field of View H: 3.2° - 44.4°
V: 2.4° - 33.6°
Focusing Range: 2.0 m - ∞(6.6 ft - ∞)
Focus Control: Far: –6 V (–12 V) DC 120 mA (50 mA), approx. 7.5 s
Near: +6 V (+12 V) DC 120 mA (50 mA), approx. 7.5 s
Zoom Control: Wide: –6 V (–12 V) DC 120 mA (50 mA), approx. 7 s
Tele: +6 V (+12 V) DC 120 mA (50 mA), approx. 7 s
Filter Size: φ46 mm, P=0.75 mm
Mount: CS-mount, 1”-32UN
Ambient Operating Temperature: –10°C - +50°C (14°F - 122°F)
Dimensions: 79(W) x 67(H) x 87(D) mm [3-1/8”(W) x 2-5/8”(H) x 3-7/16”(D)]
Weight: 260 g(0.57 lbs.)
Dimensions and weight indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORY
4-pin Connector .......................................... 1 pc.

N1098-1029 YWV8QA5113BN Printed in Japan
N 19 Imprimé au Japon
Video Imaging Systems Company
A Division of Panasonic Broadcast & Television Systems Company
A Unit of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 4H-2, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 [phone]
Southeast: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 [phone]
Midwest: 1707 North Randall Road, Elgin, IL 60123 [phone]
Southwest: 8105 Beltsline Road, Suite 100, Irving, TX 75063 [phone]
Western: 6550 Katella Ave., Cypress, CA 90630 [phone]
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada [phone]
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00630 [phone]