Panasonic CF-VEBC21Un User manual

Printed in Japan
SH1212-0
DFQW5685ZA
ENGLISH OPERATING INSTRUCTIONS
DEUTSCH
BEDIENUNGSANLEITUNG
FRANÇAIS
INSTRUCTIONS D’UTILISATION
日本語 取扱説明書
保証書付き（日本国内向け）
・取扱説明書をよくお読みのうえ、正しく安全にお使いください。
・ご使用前に「安全上のご注意」（50 ページ）を必ずお読みください。
・
 保証書は「お買い上げ日・販売店名」などの記入を確かめ、取扱説明書とともに大切に保管してください。
Port Replicator / Portreplikator /
Duplicateur de ports /
ポートリプリケーター
Model No. CF-VEBC21U
Downloaded from ManualsNet.com search engine

2
ENGLISH
Contents
Safety Precautions ............................................................ 2
Regulatory Information ..................................................... 3
Introduction ........................................................................ 5
Handling Care..................................................................... 6
Names and Functions of Parts......................................... 7
Connecting / Disconnecting ............................................. 8
Using the External Display ............................................. 10
Using the Drive................................................................. 11
Troubleshooting............................................................... 14
Specifications .................................................................. 15
To reduce the risk of injury, loss of life, electric
shock, fire, malfunction, and damage to equipment
or property, always observe the following safety
precautions.
Explanation of symbol word panels
The following symbol word panels are used to clas-
sify and describe the level of hazard, injury, and
property damage caused when the denotation is
disregarded and improper use is performed.
WARNING
Denotes a potential hazard that could result in serious
injury or death.
CAUTION
Denotes a hazard that could result in minor injury.
The following symbols are used to classify and describe
the type of instructions to be observed.
These symbols are used to alert users to a spe-
cific operating procedure that must not be per-
formed.
This symbol is used to alert users to a specific
operating procedure that must be followed in
order to operate the unit safety.
WARNING
If a Malfunction or Trouble Occurs, Immedi-
ately Stop Use
If a Malfunction Occurs, Immediately Unplug
the AC Plug and Remove the Unit From This
Product
•This product is damaged
•A foreign object is inside this product
•Smoke is emitted
•An unusual smell is emitted
•Unusually hot
Continuing to use this product while any of the
above conditions are present may result in fire or
electric shock.
•If a malfunction or trouble occurs, immediately
unplug the AC plug and remove the unit from
this product. Then, contact your technical sup-
port office for repair.
Do Not Touch This Product In a Thunderstorm
If Connected with the AC Cable or Any Other
Cables
Electric shock may result.
Do Not Place Containers of Liquid or Metal
Objects on Top of This Product
If water or other liquid spills, or if paper clips,
coins, or foreign matter get inside this product,
fire or electric shock may result.
•If foreign matter has found its way inside,
immediately unplug the AC plug and remove
this product from the unit. Then contact your
technical support office.
Do Not Connect the AC Adaptor to a Power
Source Other Than a Standard Household AC
Outlet
Otherwise, a fire due to overheating may result.
Connecting to a DC/AC converter (inverter) may
damage the AC adaptor. On an airplane, only
connect the AC adaptor/charger to an AC outlet
specifically approved for such use.
Safety Precautions
Downloaded from ManualsNet.com search engine

3
CAUTION
Do Not Place This Product on Unstable Sur-
faces
If balance is lost, this product may fall over or
drop, resulting in an injury.
Do Not Keep This Product Wherever There
is a Lot of Water, Moisture, Steam, Dust, Oily
Vapors, etc.
Otherwise, possibly resulting in fire or electric
shock.
Do Not Leave This Product in High Tempera-
ture Environment for a Long Period of Time
Leaving this product where it will be exposed to
extremely high temperatures such as near fire or
in direct sunlight may deform the cabinet and/or
cause trouble in the internal parts. Continued use
in such a resulting condition may lead to short-
circuiting or insulation defects, etc. which may in
turn lead to a fire or electric shocks.
Use Only the Specified AC Adaptor With This
Product
Using an AC adaptor other than the one supplied
(supplied with the unit or one sold separately as
an accessory) may result in a fire.
Do Not Connect a Telephone Line, or a Net-
work Cable Other Than the One Specified,
Into the LAN Port
If the LAN port is connected to a network such as
the ones listed below, a fire or electric shock may
result.
•Networks other than 1000BASE-T,
100BASETX or 10BASE-T
•Phone lines (IP phone (Internet Protocol Tele-
phone), Telephone lines, internal phone lines
(on-premise switches), digital public phones,
etc.)
Do Not Look Into the CD/DVD Drive
Looking directly at the internal laser light source
may result in damage to eyesight.
Do Not Use Discs That Are Cracked or De-
formed
Because the discs rotate at high speeds, dam-
aged discs may break apart causing injury.
•Discs that are not round and discs that have
been repaired using adhesives are similarly
dangerous, and so should not be used.
Regulatory Information
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private house-
holds) This symbol on the products and/or accompanying documents means that used electrical and electronic prod-
ucts should not be mixed with general household waste.
Please dispose of this item only in designated national waste electronic collection schemes, and not in the
ordinary dust bin.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further informa-
tion.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of
disposal. 36-E-1
Do not use other than the specified AC Adaptor (Model No. CF-AA6413C).
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EX-
POSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
The following label is put on the bottom of the Port Replicator. 12-E-1
Downloaded from ManualsNet.com search engine

4
For U.S.A.
Federal Communications Commission Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.●
Increase the separation between the equipment and receiver.●
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.●
Consult the Panasonic Service Center or an experienced radio/TV technician for help.●
Warning
To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral.
Also, any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device is Class B verified to comply with Part 15 of FCC Rules when used with Panasonic Notebook Computer.
Responsible Party: Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP5 (1-800-527-8675) 6-M-1
For Canada/Pour le Canada
Canadian ICES-003
CAN ICES-003(B) / NMB-003(B)
7-M-3
For Europe
Interface Cable
Use of an interface cable longer than 3 m {9.84 feet} is not recommended. 11-E-1
Declaration of Conformity (DoC)
“Hereby, Panasonic declares that this Port Replicator is in compliance with the essential re-
quirements and other relevant provisions of EU Council Directives.”
Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany 18-E-0
For India
For the purpose of recycling to facilitate effective utilization of resources, please return this product to a
nearby authorized collection center, registered dismantler or recycler, or Panasonic service center when dis-
posing of this product.
Please see the Panasonic website for further information on collection centers, etc.
http://www.panasonic.co.in/wps/portal/home 68-M-1
Regulatory Information
Downloaded from ManualsNet.com search engine

5
Thank you for purchasing the port replicator for the Panasonic CF-C2 notebook computer series*1.
In combination of the computer and this product, you can connect variety of devices.
*1 This port replicator cannot be used for other models.
Accessories

Introduction
Operating Instructions (This book)............................................................................1
DVD Drive Utility Disc
*2 ................................................................................................1
*2 This contains the programs used to install “Roxio CreatorTM LJB (hereafter, Roxio Creator LJB)” and
“PowerDVDTM (OEM Version) (hereafter, PowerDVD)”.
About software overview and installing the software, see “Software Guide” in “DVD Drive Utility Disc”.
See “Software Guide” in “DVD Drive Utility Disc”:
1.Log on to Windows as an administrator.
2.Set “DVD Drive Utility Disc” in the drive.
3. Windows 8
ARight-click any empty location on the Start screen and click [All apps] on the toolbar.
BClick [Run] under “Windows System”, input “x:\Manual\index.hta”*3 then click [OK].
Windows 7
Click (Start) and input “x:\Manual\index.hta”*3 in [Search programs and files] and press
Enter
.
*3 “x” is the drive letter. You can change the letter to suit your preference.
NOTE
This manual explains the procedure for default settings. The procedure may differ according to the set-
●
tings.
Windows 8
●indicates Windows®8 Operating System.
Windows 7
●indicates Windows®7 Professional Operating System.

●: Page in these Operating Instructions.
●: Reference to the on-screen manuals of the computer.
Some illustrations are simplified to help your understanding and may look different from the actual unit.
●
Microsoft®and Windows®are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
Roxio Creator is a trademark or registered trademark of Corel Corporation in the United States and/or other
countries.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their
respective own companies.
Downloaded from ManualsNet.com search engine

6
Handling Care
Drive Handling Care

Do not expose the drive to excessive smoke that
●
may leave a residue, e.g., oil smoke, or tobacco
smoke. Doing so can shorten the life of the drive
lens.
We recommend cleaning the drive lens with an
●
air puffer used for camera lenses.
(Do not use any spray-type of lens cleaning prod-
ucts.)
When opening/closing the tray
When the computer is on, use the eject button
●
(page 11) or eject through Windows.
When inserting or removing a disc, be careful
●
not to touch the lens and other parts of the laser
pickup.
Do not leave the tray open and do not touch the
●
lens and other parts of the laser pickup.
The laser pickup and disc can become dusty in
some conditions. It may cause malfunction in
reading or writing.
Do not apply excessive force to the tray in the
●
open position.
Never insert a foreign object such as a paper clip
●
into the drive.
Doing so may cause malfunction.
Do not place items other than discs on the tray.
●
While the drive is being accessed
Do not open the tray or move the Port Replicator
●
while the drive is being accessed.
Doing so could cause the disc to shift position
and this may damage the disc, or cause the drive
to malfunction.
In addition, after running an application involv-
ing access to a disc, close the application before
opening the tray.
Do not apply excessive shocks or disconnect/
●
connect cables, cards, etc.
Doing so may result in read/write errors.
Disc Handling Care

Before using a disc, carefully read the operating/
handling instructions and package of the disc.
If the discs are not handled appropriately, they may
become dirty or scratched. Furthermore the writing
speed may get slower and the data may not be cor-
rectly written on or read from the disc. Other dam-
age may cause a drive failure.
Use discs with the appropriate write/rewrite
●
speeds.
Do not touch the disc surface (the side with no
●
printing).
Keep the disc surface clean and free from dirt,
●
dust, fingerprints and scratches.
Do not write on the surface of the disc with a
●
ballpoint pen or other writing instrument.
Do not drop, bend, or place heavy objects on top
●
of discs.
Do not place or store discs in locations exposed
●
to heat, direct sunlight, humidity or dust.
If a disc is brought from a cold to a warm loca-
●
tion, condensation may form on the disc.
<For read-only discs>
Wipe off the condensation using a soft, dry, lint-
free cloth before using the disc.
<For recordable/rewritable discs>
Wait until the condensation dries.
When not using discs, keep them in their protec-
●
tive cases or cartridges.
To clean discs
<For read-only discs>
Wipe discs with a dry, soft cloth from the center
toward the edge.
If discs get very dirty, wipe with a moist, soft cloth
from the center toward the edge, then wipe again
with a dry cloth to take up remaining moisture.
Correct Incorrect
<For recordable/rewritable discs>
Use the recordable/rewritable disc cleaner to
clean these discs.
Do not use a cloth, CD cleaners or any other such
cleaners under any circumstances.
How to hold a disc
Correct Incorrect
Downloaded from ManualsNet.com search engine

7
Names and Functions of Parts
The port replicator allows your peripheral devices to function exactly as if they were connected directly to
the computer. (Refer to “Description of Parts” in the “Operating Instructions” accompanying the computer.)
CAUTION
Do not touch the port replicator connector, pins or terminals of the port replicator.
●
Rear

Security Lock: LOCK
A Kensington cable can be connected.
For more information, read the manual
that comes with the cable.
USB 3.0 Ports:
These can be used only when
the AC adaptor is connected.
VGA Port:
Connect the external display compatible with analog
interface.
The HDMI2 port and VGA port cannot be used
simultaneously. If cables are connected to both the
HDMI2 and VGA ports, the VGA port will have priority.
HDMI Ports:
Left: HDMI1 port
Right: HDMI2 port
Connector for HDMI compatible digital display.
It is not compatible with the analog display.
The display specifications of the maximum resolution, etc. that
can be output differ according to the specifications of the
device connected.
For details, refer to the specifications of the device connected.
The HDMI2 port and VGA port cannot be used simultaneously.
If cables are connected to both the HDMI2 and VGA ports, the
VGA port will have priority.
LAN Port:
DC-IN Jack:
DC IN 15.6V
Front/Right Side

Port Replicator Connector
This connects to the
Expansion Bus Connector on
the bottom of the computer.
Latch CD/DVD Drive
Lever
Slide the lever all the way
back to release the computer.
Downloaded from ManualsNet.com search engine

8
Connecting / Disconnecting
CAUTION
Do not connect or disconnect the port replicator while the computer is powered on or in the sleep or
●
hibernation mode.
Connecting

Power off the computer, and disconnect all cables from the com-A
puter.
Connect the AC adaptor that came with the computer to the portB
replicator and plug the other end into an AC outlet.
CAUTION
Refer to the “Operating Instructions” accompanying computer for information on proper handling of
●
the AC adaptor and AC cord.
Align the front of the computer with the latch on the port replica-C
tor, and gently place the computer on the port replicator.
CAUTION
Do not connect the computer to a port replicator while the AC
●
adaptor or other cables is connected to the computer.
Do not attempt to make connections if there is any object
●
between the computer and the port replicator. Doing so could
damage the computer and the ort replicator.
Push the areas indicated by the arrows to set the computer.D
CAUTION
While connecting the computer to the port replicator:
●
Do not attempt to move the port replicator.•
Do not open the display wider than necessary (180° or more), and do not apply excessive pressure to•
the LCD.
It is impossible to remove the battery pack.•
If the computer malfunctions while the port replicator is attached, disconnect the port replicator and
●
check to see if the computer operates normally. If the computer operates normally, the port replicator
may be malfunctioning. Contact your technical support office.
Disconnecting

Power off the computer and close the display.A
Slide the lever all the way back.B
The computer’s connector disengages the port replicator connector of the
port replicator.
Lift up the computer to remove it from the port replicator.C
Downloaded from ManualsNet.com search engine

9
CAUTION
If the port replicator is connected to the computer, connect the LAN cable and VGA cable to the jack and
●
port on the port replicator. Do not use the LAN port and VGA port on the computer.
Do not connect/disconnect peripheral devices in sleep or hibernation.
●
If devices connected to USB 3.0 ports do not operate, confirm the AC adaptor is connected to DC-IN of
●
the port replicator.
When using the USB port, make sure that [Port Replicator USB Port] is enabled in the [Advanced] menu
●
of the Setup Utility.
For more information about the settings and preparations of the peripheral devices, refer to the periph-
●
eral devices’ own operating instructions.
When connecting the external display to either of the ports, lines or letters may blur. In that case, lower
●
the resolution.
Downloaded from ManualsNet.com search engine

10
Refer to Reference Manual “External Display”.
Switching the Display

To switch using the keys
PressA key + or + .
Click the display mode.B
To switch using the display driver
Right-click the desktop, and click [Graphics Properties].A
Click [Multiple Displays].B
Select the display in [Operating Mode], and click [Apply].C
Click [OK].D
If necessary, click [General Settings], set the color depth, resolution, etc., and click [OK].E
Windows 7
When 2 external displays compatible with analog interface and HDMI1 respectively are connected at the
same time and when [Display] is set to [External Monitor] in the Setup Utility, the display compatible with
HDMI will take priority over the display compatible with analog interface.
NOTE
When external displays are connected to both the VGA port and HDMI1 port, if you select [Clone Dis-
●
plays] or [Extended Desktop], 3 displays are shown for [Primary Display] and [Second Display] respec-
tively under [Multiple Displays]. An HDMI compatible display or analog display are indicated as [Digital
Television] and internal LCD as [Built-in Display].
When switching from the analog display to the internal display, the following message may appear on
●
the analog display.
Out of range•
Switching the audio output destination while connecting the HDMI

compatible display
Windows 8
A
Open the Control Panel, and then click [Hardware and Sound] - [Sound].
To open the Control Panel, proceed as follows on the [Start] screen.
1.Right-click any empty location on the Start screen.
2.Click [All Apps] on the toolbar.
3.Click [Control Panel] under “Windows System Tools”.
Windows 7
Click (Start) - [Control Panel] - [Hardware and Sound] - [Sound].
Select the audio output destination.B
Click [Set Default] and click [OK].C
NOTE
When connecting an HDMI compatible display without speakers mounted, audio may not be output from
●
this unit and the HDMI compatible display. Follow the above steps to change the setting so the audio is
output from this unit’s speaker.
Using the External Display
Downloaded from ManualsNet.com search engine

11
Setting a Disc

Turn on the computer.A
A
Press the eject button (A) and slowly pull out the tray.B
Insert/Remove the disc.C
To insert•
Set the disc with the label side up and press the center of the
disc until it clicks in place.
To remove•
Press on the center spindle (B) and carefully lift up the edge of
the disc.
Close the tray.D
Do not press the eject button.
B
C
NOTE
The drive indicator
●on the computer will blink while the disc is being accessed.
To remove a disc when the computer is powered off, insert a pointed object (e.g., the bent-out tip of a
●
paper clip) into the emergency hole (C). Pushing it to the end allows the tray to come out.
If the vibration of the drive is excessive, check the disc.
●
For AutoPlay CD/DVD:
●
If an AutoPlay CD/DVD does not start after the computer resumes from sleep or hibernation, remove•
the disc from the drive and then reinsert it after waiting 15 seconds.
An AutoPlay CD/DVD may start during file access depending on the status of the disc.•
When playing back video from a disc, playback may not be smooth in some conditions.
●
Power-saving Mode

If the drive is not accessed for 30 seconds, the drive motor will automatically be shut down to reduce the
power consumption. When the drive is accessed again, the drive motor is turned on. In this case, reading of
the disc data will take approximately 30 seconds.
To play DVD-Video or MPEG2 files

Install the DVD playback software using “DVD Drive Utility Disc”.
For information on how to install the software, refer to “Software Guide” with “DVD Drive Utility Disc”.
Region Code Setting

DVD-Videos are allocated to region codes according to where they are sold. To play a DVD-Video, the DVD
disc and the drive must have the corresponding region code.
e.g.,
For U.S.A. and Canada: “1”
For Europe: “2”
Using the Drive
Downloaded from ManualsNet.com search engine

12
The region code of the drive is not set at purchase. The operation depends on the DVD-Video that is first
●
played.
DVD-Video with a specific region code:•
The drive will automatically be set at the same region code as the DVD-Video.
DVD-Video with multiple region codes:•
The screen to change the region code appears. Set the region code.
CAUTION
You can change the region code setting up to five times including the initial setting. Be extremely careful
●
because you cannot change the region code anymore after the fifth change, even if you reinstalled the
operating system.
Any problem resulting from illegal changing or altering of the region code is the user’s responsibility.
●
NOTE
The screen to change the region code appears when the DVD-Video has only one region code and the
●
drive is set for another region code.
Writing to Discs

Windows 8 and Windows 7 include the standard function that enables you to write or rewrite data to a
●
disc.
You can copy a CD/DVD or create a music CD, data CD/DVD, etc. by installing “Roxio Creator LJB” us-
●
ing the “DVD Drive Utility Disc”.
Be sure to use discs conforming to the proper write speeds. (
●page 15)
If the write operation is to involve a long period of time, be sure to connect the AC adaptor of the com-
●
puter. If the battery power runs low and the power of the computer is cut, the write operation may end in
failure.
You can read from/write to the following discs.
●
CD-R CD-RW
DVD-RDVD-RAM*1DVD-RW*2
DVD-R DL
+RW
+R +R DL
You can read from the following discs.
●
CD-ROM CD TEXT CD-EXTRACD DIGITAL
AUDIO
Video CD Photo CD DVD-ROM DVD-Video
*1 DVD-RAM: Only non-cartridge type or removable cartridge type can be used.
*2 Does not support DVD-RW Ver.1.0.
Using the Drive
Downloaded from ManualsNet.com search engine

13
Recommended discs for writing
●
The quality of written data depends on the disc.•
<CD-R>
TAIYO YUDEN Co., Ltd.•
<CD-RW/High-Speed CD-RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
<Ultra-Speed CD-RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
<DVD-R>
Panasonic Corporation•
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
TAIYO YUDEN Co., Ltd.•
<DVD-R DL>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
TAIYO YUDEN Co., Ltd.•
<DVD-RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
Victor Company of Japan, Limited•
<DVD-RAM>
Panasonic Corporation•
HITACHI MAXELL, Ltd.•
<+R / +RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
<High Speed +RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
<+R DL>
MITSUBISHI KAGAKU MEDIA CO., Ltd.•
DVD discs you can use for writing
●
<DVD-R for General>
1X-SPEED (4.7• GB)
1-2X-SPEED (4.7• GB)
1-4X-SPEED (4.7• GB)
1-8X-SPEED (4.7• GB)
1-16X-SPEED (4.7• GB)
<DVD-R DL>
2-4X-SPEED (8.5• GB)
2-8X-SPEED (8.5• GB)
<DVD-RW>
1X-SPEED (4.7• GB/9.4 GB)
1-2X-SPEED (4.7• GB/9.4 GB)
2-4X-SPEED (4.7• GB/9.4 GB)
2-6X-SPEED (4.7• GB/9.4 GB)
<DVD-RAM>
2X-SPEED (4.7• GB/9.4 GB)
2-3X-SPEED (4.7• GB/9.4 GB)
2-5X-SPEED (4.7• GB/9.4 GB)
<+R>
1-2.4X-SPEED (4.7• GB)
1-4X-SPEED (4.7• GB)
1-8X-SPEED (4.7• GB)
1-16X-SPEED (4.7• GB)
<+R DL>
2.4X-SPEED (8.5• GB)
2.4-8X-SPEED (8.5• GB)
<+RW>
1-2.4X-SPEED (4.7• GB)
1-4X-SPEED (4.7• GB)
<High-Speed +RW>
3.3-8X-SPEED (4.7• GB)
Downloaded from ManualsNet.com search engine

14
Devices connected to the USB 3.0 ports
do not operate
Check if the AC adaptor is connected to the power terminal
●
of the port replicator.
Power can be turned on, however, Win-
dows does not start up normally
Disconnect peripheral devices, such as a USB memory. If
●
disconnecting the peripheral devices can start up Windows,
the problem may be with the peripheral devices. Contact the
manufacturer of such devices.
The computer does not resume (return)
from sleep or hibernation
Slide the power switch to turn the power on in the following
●
cases. Note that unsaved data is lost.
The AC adaptor was disconnected in sleep.•
Peripheral devices were connected/disconnected.•
The power switch was slid for 4 seconds or more and Win-•
dows was forcibly terminated.
The computer does not power off (Win-
dows does not shut down)
If a peripheral is connected, disconnect it, and then shut
●
down.
If it is possible to shut down when the peripheral is discon-
nected, then there may be a problem with the peripheral.
Contact the manufacturer of such devices.
Nothing is displayed or the display does
not appear properly on the external dis-
play connected to the HDMI terminal.
The HDMI compatible display does not support the HDMI
●
connection on the computer.
When the HDMI compatible display does not support the
HDMI connection on the computer, the screen may appear
blurry, or the output destination may not be switched by
pressing key + or + .
The audio output from the HDMI com-
patible display cannot be turned on/off Pressing
●+ on the computer cannot turn on/off the
audio output from the HDMI compatible display.
The computer does not recognize the
drive
Restart the computer.
●
Power off the computer, then remove and connect the com-
●
puter again.
The drive indicator does not light Is the disc loaded on the tray correctly? (
●page 11)
Cannot play disc or read data from it Is the disc bent, scratched, or dirty?
●
An error may occur if, after the tray has been closed or operation
●
has been resumed from the sleep/hibernate modes, the drive is
accessed before the drive indicator goes off. Also, an error
may occur if the drive is accessed by the application software
automatically. In a case like this, remove the disc, re-insert it,
and try again.
(page 11)
“Roxio Creator LJB” does not work prop-
erly
Is writing software other than “Roxio Creator LJB” installed?
●
Uninstall the writing software other than “Roxio Creator
LJB.”
Cannot eject disc Turn on the computer.
●
To remove a disc when the computer is
●
powered off, insert a pointed object (e.g., the
bent-out tip of a paper clip) into the emergen-
cy hole (A). Pushing it completely to the end
will free the tray so that it can be pulled out.
A
If a disc with fingerprints or other dirt is used, you may not
●
be able to remove it. Use a clean disc. (page 6)
The disc tray does not close
Do not touch the eject button when closing the tray.
●
Other disc operation problems Use another drive or media.
●
Troubleshooting
Downloaded from ManualsNet.com search engine

15
Specifications
Item Description
Power Supply Input DC16 V(Use the specified AC adaptor supplied with the com-
puter or one sold separately as an accessory.)
Supported AC adapter*1 Input: 100 Vto 240 VAC, 50 Hz/60 Hz, Output: 16 VDC, 4.06 A
Connector 100-pin
USB Port*2 USB × 4 (USB 3.0)
Allowable current for each port: 900 mA
LAN Port IEEE802.3ab 1000BASE-T, IEEE802.3u 100BASE-TX,
IEEE802.3 10BASE-T (RJ-45)
HDMI Port*2*3*4 HDMI × 2 For exclusive use with HDMI standard
VGA Port*4 Mini Dsub 15-pin female (Analog interface)
Physical Dimensions (W x H x D) Approx. 351 mm x 271 mm x 63 mm {Approx. 13.8” x 10.7” x 2.5”}
Weight Approx. 1.85 kg {4.08 lb.}
CD/
DVD
Drive
Data
Transfer
Rate*5
Reading*6 DVD-ROM: 8X (Max.), CD-ROM: 24X (Max.)
Writing*7 CD-R: 24X (Max.), CD-RW: 4X
High-Speed CD-RW: 10X
Ultra-Speed CD-RW: 24X (Max.)
DVD-R: 8X (Max.), DVD-R DL: 6X (Max.)
DVD-RW: 6X (Max.), DVD-RAM: 5X (Max.)
+R: 8X (Max.), +R DL: 6X (Max.)
+RW: 4X (Max.), High Speed +RW: 8X (Max.)
Supported
Discs/For-
mat*8
Reading DVD-ROM (4.7 GB, 8.5 GB, 9.4 GB, 17 GB), DVD-Video,
DVD-R (1.4 GB, 3.95 GB, 4.7 GB), DVD-R DL (8.5 GB),
DVD-RW*9 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB),
DVD-RAM*10 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB), +R (4.7 GB),
+R DL (8.5 GB), +RW (4.7 GB), High Speed +RW (4.7 GB),
CD-Audio, CD-ROM, CD-R, Photo CD, Video CD, CD-RW,
High-Speed CD-RW, Ultra-Speed CD-RW, CD TEXT,
CD-EXTRA
Writing DVD-R (1.4 GB, 4.7 GB for General), DVD-R DL (8.5 GB),
DVD-RW*9 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB),
DVD-RAM*10 (1.4 GB, 2.8 GB, 4.7 GB 9.4 GB), +R (4.7 GB),
+R DL (8.5 GB), +RW (4.7 GB), High Speed +RW (4.7 GB),
CD-R, CD-RW, High-Speed CD-RW, Ultra-Speed CD-RW
Buffer underrun error prevention function Supported
Cache memory 2 MB*11
*1 <Only for North America>
The AC adaptor is compatible with power sources up to 240 V AC adaptor. This computer is supplied with a 125 V
AC compatible AC cord.
<When using with 115 V/240VAC>
Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.3 W) simply by having the
AC adaptor plugged into an AC outlet.
*2 Does not guarantee operation of all USB and HDMI-compatible peripherals.
*3 When connecting the HDMI compatible display, specifications such as maximum resolutions available to output
differ, depending on the specifications of the connected devices. See the specifications of the connected device for
details.
*4 The HDMI2 port and VGA port cannot be used simultaneously. If cables are connected to both the HDMI2 and
VGA ports, the VGA port will have priority.
*5 The data transfer rate of DVD per 1X speed is 1,350 KB/s.
The data transfer rate of CD per 1X speed is 150 KB/s.
Downloaded from ManualsNet.com search engine

16
*6 If an unbalanced disc (e.g., a disc with which the balance has been displaced from the center) is inserted, the
speed may become slower if there are large vibrations while the disc is rotating.
*7 Depending on the disc, the writing speed may become slower.
*8 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.
*9 Does not support DVD-RW Ver.1.0.
*10 DVD-RAM: Only non-cartridge type or removable cartridge type can be used.
*11 1 MB = 1,048,576 bytes.
Specifications
Downloaded from ManualsNet.com search engine

17
DEUTSCH
Inhalt
Sicherheitsvorkehrungen ............................................... 17
Vorgeschriebene Informationen .................................... 18
Einführung ........................................................................ 20
Hinweise zum Umgang.................................................... 21
Namen und Funktionen der Teile ................................... 23
Anschließen / Entfernen.................................................. 24
Verwendung des externen Displays.............................. 26
Gebrauch des Laufwerks................................................ 27
Störungsbehebung.......................................................... 30
Technische Daten............................................................. 32
Befolgen Sie die folgenden Sicherheitsvorkehrun-
gen, um das Risiko von Verletzungen, Todesfällen,
elektrischen Schlägen, Feuer, Fehlfunktionen und
Geräte- oder Sachschäden zu verringern.
Erklärung der Symbol/Wort-Tafeln
Die folgenden Symbol/Wort-Tafeln werden verwen-
det, um den Grad der Gefährdung, Verletzungen
und Sachschäden zu klassifizieren und zu beschrei-
ben, die verursacht werden, wenn die Bezeichnun-
gen nicht beachtet werden und ein unsachgemäßer
Gebrauch geschieht.
WARNUNG
Bezeichnet eine potentielle Gefährdung, die zu schw-
eren Verletzungen oder Tod führen kann.
ACHTUNG
Bezeichnet eine potentielle Gefährdung, die zu schw-
eren Verletzungen oder Tod führen kann.
Die folgenden Symbole werden verwendet, um die Art
der zu beachteten Anweisungen zu klassifizieren und zu
beschreiben.
Diese Symbole werden verwendet, um Benutzer
auf einen bestimmten Vorgang hinzuweisen, der
nicht ausgeführt warden darf.
Dieses Symbol wird verwendet, um Benutzer
auf einen bestimmten Vorgang hinzuweisen, der
ausgeführt werden muss, um das Gerät sicher zu
betreiben.
WARNING
Bei Auftreten einer Fehlfunktion oder Störung
unmittelbar den Betrieb einstellen
Entfernen Sie beim Auftreten einer Fehlfunk-
tion unverzüglich den Netzstecker von tren-
nen Sie die Verbindung zwischen dem Gerät
und diesem Produkt
•Dieses Produkt ist beschädigt
•Innerhalb des Produkts befindet sich ein
Fremdobjekt
•Rauchentwicklung
•Ungewöhnlicher Geruch
•Außergewöhnlich heiß
Bei Weiterverwendung dieses Produkts unter den
oben aufgeführten Bedingungen besteht Brand-
oder Stromschlaggefahr.
•Entfernen Sie beim Auftreten einer Fehlfunk-
tion unverzüglich den Netzstecker von tren-
nen Sie die Verbindung zwischen dem Gerät
und diesem Produkt. Bitte wenden Sie sich
anschließend zur Reparatur an den technis-
chen Kundendienst.
Berühren Sie dieses Produkt nicht während
eines Gewitters, falls es mit dem Stromkabel
oder einem sonstigen Kabel verbunden ist
Es besteht Stromschlaggefahr.
Stellen Sie keine Behälter mit Flüssigkeit oder
Metallobjekte auf diesem Produkt ab
Falls Wasser oder sonstige Flüssigkeiten,
Büroklammern, Münzen oder Fremdkörper in
dieses Produkt geraten, besteht Brand- und
Stromschlaggefahr.
•Wenn Fremdkörper hineingelangen sollten,
entfernen Sie den Netzstecker sofort und
entfernen Sie das Gerät von diesem Produkt.
Wenden Sie sich anschließend an den tech-
nischen Kundendienst.
Sicherheitsvorkehrungen
Downloaded from ManualsNet.com search engine

18
Sicherheitsvorkehrungen
WARNING
Schließen Sie das Netzteil auf keinen Fall an
einer anderen Stromquelle als einer normalen
Wechselstrom-Steckdose an
Andernfalls kann es durch Überhitzung zu einem
Brand kommen. Durch Anschluss an einen Gle-
ichstrom-/Wechselstromkonverter (Wechsel-
richter) kann das Netzteil beschädigt werden.
Schließen Sie in einem Flugzeug das Netzteil/
Ladegerät nur an Wechselstromanschlüssen an,
die für derartige Verwendung zugelassen sind.
ACHTUNG
Stellen Sie dieses Produkt nicht auf instabilen
Oberflächen ab
Wenn dieses Produkt aus dem Gleichgewicht
gerät, kann es umkippen oder herunterfallen,
was zu Verletzungen führen kann.
Bringen Sie dieses Produkt nicht in die Um-
gebung von Wasser, Feuchtigkeit, Dampf,
Staub, öligen Dämpfen usw
Dies kann zu Bränden oder elektrischen Schlä-
gen führen.
Bewahren Sie dieses Produkt nicht für län-
gere Zeit in Umgebungen mit hohen Tempera-
turen auf
Durch Aufbewahren dieses Produkts an Orten mit
extrem hohen Temperaturen, z. B. in der Nähe
von Feuer oder durch direkte Sonneneinstrahl-
ung, kann das Gehäuse verformt und können
Schäden an den internen Bauteilen verursacht
werden. Durch längeren Einsatz unter solchen
Bedingungen kann es zu Kurzschlüssen oder
defekten Isolierungen kommen, die wiederum zu
Bränden oder elektrischen Schlägen führen kön-
nen.
Verwenden Sie nur das angegebene Netzteil
für dieses Produkt
Die Verwendung eines anderen Netzteils als des
mitgelieferten (mit dem Gerät mitgeliefert oder
separat als Zusatzteil verkauft) kann zu einem
Brand führen.
Schliessen Sie niemals Telefonkabel oder von
unseren Empfehlungen abweichende Netz-
werkkabel an den LAN-Anschluss an
Falls Sie den LAN-Anschluss mit einem anderen
Netzwerk (wie mit den nachstehend aufgefüh-
rten) verbinden, besteht Brand- und Strom-
schlaggefahr.
•Von 1000BASE-T, 100BASE-TX oder
10BASE-T abweichende Netzwerke
•Telefonleitungen (IP-Telefon (Internet Proto-
col-Telefon), Telefonkabel, interne Telefonlei-
tungen (Telefonanlagen), öffentliche Digitalt-
elefone, usw.)
Nicht in das CD/DVD-Laufwerk blicken
Der direkte Blick in die interne Laser-Lichtquelle
kann zu Augenschäden führen.
Keine CDs mit Rissen oder Verformungen
verwenden
Auf Grund der hohen Rotationsgeschwindigkeit
können beschädigte CDs auseinander brechen
und Verletzungen verursachen.
•CDs, die keine runde Form aufweisen oder
mit Klebstoffen repariert wurden, sind ähnlich
gefährlich und sollten daher nicht verwendet
werden.
Vorgeschriebene Informationen
Benutzerinformationen zur Entsorgung von elektrischen und elektronischen Geräten (private
Haushalte)
Entsprechend der grundlegenden Firmengrundsätzen der Panasonic-Gruppe wurde ihr Produkt
aus hochwertigen Materialien und Komponenten entwickelt und hergestellt, die recycelbar und
wieder verwendbar sind.
Dieses Symbol auf Produkten und/oder begleitenden Dokumenten bedeutet, dass elektrische und
elektronische Produkte am Ende ihrer Lebensdauer vom Hausmüll getrennt entsorgt werden müssen.
Bringen Sie bitte diese Produkte für die Behandlung, Rohstoffrückgewinnung und Recycling zu den einge-
richteten kommunalen Sammelstellen bzw.
Wertstoffsammelhöfen, die diese Geräte kostenlos entgegennehmen.
Die ordnungsgemäße Entsorgung dieses Produkts dient dem Umweltschutz und verhindert mögliche
schädliche Auswirkungen auf Mensch und Umwelt, die sich aus einer unsachgemäßen Handhabung der
Geräte am Ende Ihrer Lebensdauer ergeben könnten.
Genauere Informationen zur nächstgelegenen Sammelstelle bzw. Recyclinghof erhalten Sie bei Ihrer Ge-
meindeverwaltung.
Downloaded from ManualsNet.com search engine

19
WARNUNG!
DIESES PROUKT ERZEUGT LASERSTAHLUNG.
DURCHFÜHRUNG ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN KANN ZU GEFÄHR-
LICHER STRAHLUNG FÜHREN.
REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL DURCHGE-
FÜHRT WERDEN.
Der folgende Aufkleber ist unten an dem Portreplikator angebracht. 12-G-1
Für Europa
Schnittstellenkabel
Verwendete Schnittstellenkabel sollten eine Länge von 3 Metern möglichst nicht überschreiten. 11-G-1
Konformitätserklärung (DoC)
“Hiermit erklärt Panasonic, dass sich dieser Portreplikator mit den grundlegenden Anforderun-
gen und anderen relevanten Vorschriften der Richtlinien des Europäischen Rates in Überein-
stimmung befindet.”
Autorisierter Vertreter:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germang 18-G-0
Für Geschäftskunden in der Europäischen Union
Bitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elektrische und elektronische Geräte entsorgen
möchten. Er hält weitere Informationen für sie bereit.
Informationen zur Entsorgung in Ländern außerhalb der Europäischen Union
Dieses Symbol ist nur in der Europäischen Union gültig.
Bitte treten Sie mit Ihrer Gemeindeverwaltung oder Ihrem Händler in Kontakt, wenn Sie dieses Produkt entsorgen möch-
ten, und fragen Sie nach einer Entsorgungsmöglichkeit. 36-G-1
Verwenden Sie ausschließlich das vorgeschriebene Netzteil (Modell-Nr. CF-AA6413C).
Downloaded from ManualsNet.com search engine

20
Wir freuen uns darüber, daß Sie sich zum Kauf eines Portreplikator für das Panasonic Notebook CF-C2
entschieden haben*1.
Wenn Sie dieses Gerät zusammen mit einem Computer verwenden, können Sie eine Vielzahl von Geräten
anschließen.
*1 Dieser Portreplikator kann nicht mit anderen Modellen verwendet werden.
Zubehör

Einführung
Bedienungsanleitung (dieses Handbuch).................................................................1
DVD Drive Utility Disc*2................................................................................................1
*2
Enthält die Programme für die Installation von „Roxio Creator
TM
LJB (nachstehend Roxio Creator LJB)“ und
„PowerDVD
TM
(OEM Version) (nachstehend PowerDVD)“.
Über Software-Überblick und die Installation der Software finden Sie unter „Software Guide“ in „DVD Drive
Utility Disc“.
Siehe „Software Guide“ in „DVD Drive Utility Disc“:
1.Melden bei Windows als Administrator an.
2.Stellen „DVD Drive Utility Disc“ in das Laufwerk ein.
3.
Windows 8
ARechten Maustaste auf eine leere Stelle auf dem Startseite und klicken Sie auf [Alle Apps] auf der
Symbolleiste.
BKlicken Sie auf [Ausführen], geben Sie „x:\Manual\index.hta“*3 klicken Sie dann auf [OK].
Windows 7
Klicken Sie auf (Start) und geben Sie „x:\Manual\index.hta“*3 in [Programme/Dateien durchsuchen],
und drücken Sie die .
*3
„x“ steht für den Laufwerksbuchstaben. Sie können den Brief an Ihre Vorlieben anpassen.
HINWEIS
Diese Anleitung erläutert das Verfahren für die Standardeinstellungen. Das Verfahren kann je nach den
●
Einstellungen verschieden sein.
Windows 8
●bezeichnet das Windows®8 Betriebssystem.
Windows 7
●bezieht sich auf “Windows®7 Professional Betriebssystem.

●: Verweist auf eine Seite in dieser Bedienungsanleitung.
●: Verweist auf die Online-Handbücher des Computers.
Einige Abbildungen wurden zum besseren Verständnis vereinfacht und können sich vom Gerät unter-
●
scheiden.
Microsoft®und Windows®sind eingetragene Warenzeichen von Microsoft Corporation in den USA und/oder
anderen Ländern.
Roxio Creator ist ein Warenzeichen oder ein registriertes Warenzeichen der Corel Corporation in den Verei-
nigten Staaten und/oder anderen Ländern.
HDMI, das HDMI-Logo und High-Definition Multimedia Interface sind Warenzeichen oder eingetragene
Warenzeichen von HDMI Licensing LLC in den USA und/oder anderen Ländern.
Namen von Produkten, Marken usw., die in diesem Handbuch erwähnt werden, sind Warenzeichen oder
eingetragene Warenzeichen ihrer jeweiligen Eigentümer.
Downloaded from ManualsNet.com search engine