Panasonic WJ-PB85T08 User manual

-1-
Before attempting to connect or install this product,
please read these instructions carefully and save this manual for future use.
Extend Card (O.S.D.)
1
2
3
4
5
6
7
8
MONITOR OUT
VIDEO IN
OSD
q
w
Model No. WJ-PB85T08
■Preface
The WJ-PB85T08 On Screen Display Board is an optional board for displaying the camera title,
clock, and system status on the active monitors.
■Appearance
qMonitor Output Connector (MONITOR OUT, 1 - 8)
Outputs the video signal connected to the VIDEO IN port with the character display for the
video monitor.
wVideo Input Port (VIDEO IN)
Accepts the video signal from the VIDEO OUT Port on the WJ-PB85M16 Cross Point Output
Board of the Cross Point cage (MXSW).
17
16
15
14
5
4
3
2
1
20
19
18
8
6
23
22
21
11
10
9
7
25
24 13
12
Pin No. Designation
25
24
23
22
21
20
19
18
17
16
15
14
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
VIDEO 5
VIDEO 6
VIDEO 7
VIDEO 8
Not used
Not used
Not used
Not used
Pin No. Designation
13
12
11
10
9
8
7
6
5
4
3
2
1
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Hold this board only by its edges. Otherwise components on the board may be damaged by static electricity.
Caution

SW Positions
Monitor Output
Board
No. SW2 SW1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1 - 8
9 - 16
17 - 24
25 - 32
33 - 40
41 - 48
49 - 56
57 - 64
65 - 72
73 - 80
81 - 88
89 - 96
97 - 104
105 - 112
113 - 120
121 - 128
-2-
■Board Setting
Before installing this board, the following settings should be made by qualified service personnel or system installers.
SW3
SW2SW1SW5
OFF
1234
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Reset Switch
1. Set switches (SW1 and SW2) on the board to designate the On Screen Display board number as shown in the following
table.
The factory default setting is Board Number 1 (00).
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7

1Switch Positions
-3-
2. Confirm that switches (SW3) on the board are set to
the OFF position as shown below.
SW3
OFF
1234
■Installation
The following installation should be made by qualified
service personnel or system installers.
●Installing Additional Extension
Boards
1. Remove the screws from the rear panel(s) of the
WJ-SX850 Matrix Switcher Card Cage.
432
Switch Number
OFFOFFOFFOFFSW3
2. Remove the rear panel(s).
3. Remove the front panel of the cage by removing the
two screws on the panel shown below.

4. Place the Boards into the specified positions in the
front or rear of the Cage by sliding them along the
board guides as shown below.
5. Make sure to push in the Boards until they are seat-
ed firmly.
6. Secure the rear board by tightening the two screws
on the board.
■Specifications
Video Input 1.0 V[p-p]/75Ωcomposite video signal
8 inputs 25-pin D-sub connector
Video Output: 1.0 V[p-p]/75Ωcomposite video signal
On Screen Display:
Time and Date: 3 display types selectable
Camera Title: 1 Line, 30 alphanumeric characters maximum
Dimensions: Front Board; 255(W) x 250(H) x 12(D) mm
10-1/16”(W) x 9-13/16”(H) x 1/2”(D)
Rear Board; 117.5(W) x 265(H) x 20(D) mm
4-5/8”(W) x 10-7/16”(H) x 13/16”(D)
Weight: 0.6 kg (1.3 lbs)
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
NM1099-0 YWV8QA5058AN Printed in Japan
N19
© Matsushita Communication Industrial Co., Ltd. 1999
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada [phone]
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 [phone]
Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 [phone]
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 [phone]
Midwest: 1707 North Randall Road, Elgin, IL 60123 [phone]
Western: 6550 Katella Ave., Cypress, CA 90630 [phone]
Board
Tighten screws
Tighten screws
Rear
panel
Rear
panel
Tighten screws
7. Close open spaces on the rear of the Cage with the
supplied rear panel(s).
8. Close the front of the cage by fixing the front panel.