Panasonic Arbitrator 360 Manual

Arbitrator 360
Hardware Installation
Version 2.2

1. Arbitrator Units and Cables
Camera Cable
(Short)
External GPIO
Trigger Cable
Camera
AG-CK10P
CCR24PNA
Digital Wireless
Mic Receiver &
Transmitter
In Car Mic Receiver Cable
AG-CPD20P
Recorder (VPU) 32GB SDHC Card Camera Mount Camera Cable
(Long)
Control Panel
Cable
Control Panel 2nd Backseat
Camera
CN258IR-P
LAN Cable
(Crossing type)
GPS Antenna Power Cable
for Recorder
AG-RCP30P
3rd-6th Camera
BN258IR
MN1760
2 sets of 7.5A Fuse (UL Listing) is needed for the connection between VPU
and Vehicle battery. (NOT included in the kit)
RP-SDW32GP1K
AG-CR13P
OPTIONS

Camera 2
(backseat)
(Option)
CN258IR-P
2nd/3rd
WMIC
RX/TX
(Option)
VPU
AG-CPD20P
2. Arbitrator in-car System Configuration
RX/TX
Front End
Application
WMIC RX/TX
CCR24PNA
Serial (RS-232C)
for Radar Gun USB for
Wireless LAN
Module
From 3rd Vendor
In Car Mic
Ethernet
Cable for
Wired
Upload
Toughbook
(In car PC)
Option Camera Examples
Camera 3 (LPR)
Camera 4 (Left)
Camera 5 (Right)
Camera 6 (Back)
Control Panel
(Option)
AG-RCP30P
Camera 1
(Front)
AG-CK10P
Video Out 1
for LPR/
Monitor etc
Use the mirror mode for Camera 4,
5 and 6.
If no mirror mode for these,
connect Camera 4 (Left) to Video 5
and Camera 5 (Right) to Video 4.
GPS
Antenna
Vehicle Battery
12V/24V
16 Triggers
(Siren/Light
Bar/Brake/
WMIC etc)
Power Cable
Cable Kit
AG-CR13P
External
GPIO Cable

Appendix: Camera 4, 5 and 6 video image and connection
If Left Camera (Cam4), Right Camera (Cam5) and Back Camera
(Cam6) have the Mirror mode, Connect Cam 4 to the “video in 4”,
Cam5 to “video in 5” and Cam6 to “video in 6”
Front LPR
Right
Left
Back
R-Seat
1 (Camera 1)
2
3
Cam4 Cam5
Cam6
Officer Walking Direction
65 4
1, 2 or 3
4 5
61, 2 or 3
Image will be moved 4, 6, 5 in order from left to right.
If Left Camera (Cam4), Right Camera (Cam5) and Back Camera
(Cam6) do NOT have the Mirror mode, Connect Cam 4 to the “video
in 5”, Cam5 to “video in 4” and Cam6 to “video in 6”
65 4
1, 2 or 3
4 5
61, 2 or 3
Image will be moved 5, 6, 4 in order from right to left.
Cam4 Cam5 Cam4 Cam5
Cam4Cam5 Cam4Cam5

3. Install VPU using Mounting Bracket
1. To center console
2. To trunk

4. Power cable harness for VPU, Wireless MIC and 2nd camera
1. There are basically two options for the connections.
One is with Charge Guard, another is for Accessory connection
using internal timer in VPU.
2. +12V Power line:
VPU: 1) Power line (+12V : red) must be connected to the battery
through 7.5 amp fuse (not in the kit).
2) Signal line (white) must be connected to the Charge Guard or
Accessory SW though 7.5 amp fuse (not in the kit).
Wireless MiC: Power line (+12V:red) must be connected to VPU white line.
2nd Camera: Power line (+12V: white) also must be connected to VPU white line
3. GND line:
VPU : Power cable and Trigger cable (2 lines)
Wireless Mic : Power GND and trigger GND (2 lines)
2nd Camera : Power GND (1 line)
All black lines must be connected directly to the negative terminal of the battery.

1A in-line
fuse
Recording engine
Clock
VPU
Power sw
signal(SA)
■
■
■
4-1.VPU, Wireless MIC and camera to Battery Connection (w/Charge Guard)
Receiver (RX) Cable
Car Battery
12V/24V
WMIC Receiver (RX)
Trigger GND #5
WHITE
RED
RED #1
BLACK
Fuse
7.5A
Fuse
7.5A
(+)
(-)
2nd Camera
WHITE
BLACK
Charge
Guard
power
Trigger cable GND #9
Power GND #2
All GND (black)
must be connected
to the battery (-)
Need 7.5A fuse
Please set
“Power Off Time”
to be minimum 10 min
in FE “Config” setting
in order to close the
file properly.

4-2.VPU, Wireless MIC and camera to Battery Connection (thru ACC sw)
1A in-line
fuse
Recording engine
Clock
VPU
Power sw
signal(SA)
■
■
■
Receiver (RX) Cable
Vehicle Battery
12V/24V
WMIC Receiver (RX)
Trigger GND #5
WHITE
RED
RED #1
BLACK
Fuse
7.5A
Fuse
7.5A
(+)
(-)
2nd Camera
WHITE
BLACK
power
Trigger cable GND #9
Power GND #2
All GND (black)
must be connected
to the battery (-)
ACC switch
Need 7.5A fuse
Please set
“Power Off Time”
to be minimum 10 min
in FE “Config” setting
in order to close the
file properly.

5. GPIO Trigger connection
1. This has 16 GPI inputs and 3 GPO outputs.
2. Please refer the cable color and connect to the proper device.
3. Panasonic recommends the following connection set-ups as standards.
4. Pin #9 (GND) must be connected directly to the negative terminal of the battery.
(as written in item 3)

5-1. GPIO Trigger for 16 GPIs
External GPIO Trigger Cable
(supplied)
Pin # Signal Remark Cable Color Trigger Name (Example)
9GND GND Black MUST be connected to Negative battery terminal
10 GPI 1 In Brown Wireless Mic
11 GPI 2 In Red Light Bar
12 GPI 3 In Orange Brake Indicator
13 GPI 4 In Yellow Siren Indicator
21 GPI 5 In Green Gun Lock
22 GPI 6 In Blue Wireless Mic Active indicator (H)
23 GPI 7 In Violet Wireless Mic Mute indicator (H)
24 GPI 8 In Gray Other
14 GPI 9 In Blue / White Other
15 GPI 10 In Violet / White Other
16 GPI 11 In Red / Black Other
17 GPI 12 In Orange / Black Other
3GPI 13 In Pink Other
4GPI 14 In Light Green Other
5GPI 15 In Brown / White Own(REC) / TGT(REC) (when connecting Radar/GPS)
6GPI 16 In Orange / White Own(REC) / TGT(REC) (when connecting Radar/GPS)
25 GPO 1 Out White Open Emitter (Rec, Error, Rec+Eror: Active 5V 15mA)
8GPO 2 Out Green / White Open Emitter (Rec, Error, Rec+Eror: Active 5V 15mA)
18 GPO 3 Out Yellow / Black Open Collector (Rec : Active L)
19 GPO 4 Out Red / White +5V out
GPI 1~16 L : not more than1.0V H: 4 V to 28V Input current max. 12mA
Pin#1 (Black/White) & #7 (Green/Black) are not used (can be opened)