Panasonic FV-30BW2H User manual

INSTALLATION AND
OPERATING INSTRUCTIONS
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before attempting to install, operate or
service the Panasonic product. Please carefully read “INSTALLATION INSTRUCTIONS”
(P.3 4) of this instructions before installation. Failure to comply with instructions
~
could result in personal injury or property damage. Please explain to users how to
operate and maintain the product after installation, and this booklet should be
presented to users. Please carefully read “USE AND MAINTENANCE INSTRUCTIONS”
(P.26 28) of this instructions before operation.
~
Please retain this booklet for future reference.
感謝您選用Panasonic產品。
安裝、使用和保養Panasonic產品前，請仔細閱讀本安裝使用說明書。安裝前，請務必先閱讀
“安裝注意事項”(第3 4頁)。不遵照此說明書進行操作有可能導致人員受傷或財產損失。安裝
~
完成後，請向顧客說明如何使用和維護Panasonic產品，並將此說明書交給顧客保管。使用前，
請務必先閱讀“使用及維護注意事項”(第26 28頁)。
~
請妥善保管好此說明書以備日後參考。
Thermo Ventilator
安裝使用說明書
浴室換氣暖風機
型號：
FV-30BW2H
安全指引
目錄
安裝注意事項
安裝要求
包裝附件清單
部件名稱和尺寸
安裝方法
2
3 4
~
3 4
~
5 6
~
5 6
~
7 14
~
7 14
~
6
6
7
7
ANTIBACTERIAL FUNCTION
HOW TO USE TIMER FUNCTION
HOW TO USE AIR DIRECTION FUNCTION
HOW TO USE HEATING FUNCTION
HOW TO USE DRYING FUNCTION
HOW TO USE VENTILATION FUNCTION
CARE MODE:
HOW TO USE WARM BATH FUNCTION
HOW TO USE REFRESH FUNCTION
HOW TO USE 24HR VENT. FUNCTION
HOW TO USE DRY CLOTH FUNCTION
MODE BUTTON PANEL ON MAIN BODY
TROUBLESHOOTING
WIRING DIAGRAM
SPECIFICATIONS BACK COVER
遙控器功能
定時功能的使用方法
風向功能的使用方法
暖氣功能的使用方法
乾燥功能的使用方法
換氣功能的使用方法
貼心模式：
溫暖沐浴功能的使用方法
極速排氣功能的使用方法
24小時換氣功能的使用方法
高效乾衣功能的使用方法
機體模式按鈕面板
抗菌功能
常見故障的識別與處理
電氣原理圖
末頁規格
FUNCTION OF REMOTE CONTROL
19
20
21
21
21
21
19
20
26 28
~
22 24
~
22 24
~
26 28
~
28 29
~28 29 ~
3030
15
15 15
15
16
16
17
17
18
18
19
19
2525
3030
3131
試運轉
TEST RUN
CONTENTS
2
SAFETYINSTRUCTIONS
INSTALLATIONINSTRUCTIONS
INSTALLATIONREQUIREMENTS
SUPPLIED ACCESSORIES
PARTNAMESAND DIMENSIONS
HOW TO INSTALL
USE AND MAINTENANCE INSTRUCTIONS 使用及維護注意事項
維護方法MAINTENANCE

為避免給您及其他人造成傷害，這裡我們列出了以下安全注意事項，請務必遵守，各種標誌的
含意請參見以下內容。
對希望遵守的內容和種類，用下列符號進行分類、說明。
The following instructions should be strictly observed in order to prevent injury to the
users and other people, or damage to property.
Types of instructions that should be observed have been classified and described by
the following pictorial symbols.
此標誌表示為禁止事項
This symbol indicates the item is “PROHIBITED” to do.
此標誌表示為強制事項
This symbol indicates the “COMPULSORY” item that must be followed
without failure.
此標誌表示為提示注意事項
This symbol indicates the item is “CAUTION”.
對無視表示內容，錯誤地使用時，會引起的危害或損傷的程度，用下列符號進行分類、說明。
警告
注意
本標誌所表示內容為“不遵守的話可能造成人員死亡或重傷”。
本標誌所表示內容為“不遵守的話可能造成人身輕傷或其他財產
損害”。
The degrees of injury or damage that can occur when the instructions are ignored
and if the product is not used properly have been classified and described by the
following indications.
This indication means: Must be treated seriously that this may
result in death or serious injury.
WARNING
This indication means: Must be treated seriously that this may
result in injury or physical damage.
CAUTION
安全指引 請務必遵守
2
SAFETYINSTRUCTIONS
Disconnect power supply before maintenance.
維護保養前先斷電。
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
本產品不適合有殘疾、智障或精神障礙的人士或缺乏經驗、常識者（包括兒童）維護使用，除非
在負責他們安全的人士的看護或指導下使用。在維護保養期間，兒童應該有人進行看護，以防
將產品當作玩具。

否則可能會導致火災。
Otherwise, a fire may be caused.
Doavoidtheback-flowofgasinto
theroomfromtheopenflueof
flammablegasorother open-fire
appliances.
必須避免易燃氣體從敞開的氣道或其他
燃燒燃料的設備回流進室內。
否則可能會導致火災。
Otherwise, a fire may be caused.
The product can not be located just
below a power outlet socket.
禁止把本產品安放在電源插座下使用。
Otherwise, unreliable installation
may be caused and thus the product
may fall off, resulting in injuries.
Do not install the product as the
method which is not approved in
the instruction.
禁止使用本說明書指定以外的方法
進行安裝。
否則可能會安 裝不牢固，導致 產品
掉落受傷。
Do not close to curtains and other
flammable materials when install
the product.
Otherwise, combustibles may be
inflamed.
禁止靠近窗簾和其他可燃材料安裝。
否則可能會引 燃可燃物。
否則可能會導致火災。
Otherwise, a fire may be caused.
To avoid danger arising from
wrong resetting of the thermal
circuit breaker, the product can
not be powered by using an
external switch. For example, by
a timer or connecting to a circuit
that is connected/disconnected
through timing of a universal part.
為避免由熱斷路器的誤復位產生危險，
產品不能通過外部開關裝置供電。例如，
定時器或者連接到由通用部件定時進行
通、斷的電路。
3
安裝注意事項
Make sure the power cord is
installed firmly.
確保電源線安裝到位。
否則可能會導致火災。
Otherwise, a fire may be caused.
Please select 60227 IEC 53 (RVV)
ordinary polyvinyl chloride sheathed
cord.Nominal cross-sectional area of
conductors is ²
2
3×1.5 mm .
Otherwise, it may be on fire.
否則可能會導致起火。
電源線請選用60227 IEC 53(RVV)型軟
2
線，導線的截面積為3×1.5 mm 。
INSTALLATION INSTRUCTIONS
Do not operate the product other
than the rated voltage
(220 V , 50 Hz) .
~
禁止使用額定電壓(220 V，50 Hz)以
~
外的電壓。
否則可能會損壞本產品或導致火災。
Otherwise, it may cause damages
to the product or a fire.
The product must be grounded.
Otherwise, it may cause
electric shock when there is
any trouble or electric leakage.
必須接地。
當出現故障或漏電時，可能會觸電。
Otherwise, it may cause a short
circuit, thus resulting a fire.
Please install an all-pole switch which
the contact separation is more than
3 mm and the capacity more than
250 V 13 A to control the power
~
of the product. Please install the
all-pole switch out of the bathroom
where it is easily controlled.
安裝時，須在供電線路中安裝其觸點開距
不少於3 mm 的“電源全級開關” ，以用
於接通或斷開主機電源，其額定負載能力
不小於250 V ~ 13 A，且安裝在浴室外側
方便操作的地方。
否則可能會導 致短路，導致火災。
警告
WARNING

Disconnectpowersourcebefore
workingontheproduct.
Installation and wiring should be
done by authorized person.(wiring
is required to follow the local wiring
regulations.)
The product is installed so that
switches cannot be touched by a
person in the bath or shower.
Otherwise, anelectricshockmay
becaused.
Otherwise, anelectricshockmay
becaused.
安裝、維修保養時必須斷開電源。
否則可能會導致觸電。
否則可能會導致觸電。
否則可能會導致火災。
產品的安裝，應使得浴缸內或淋浴區的
人不能夠觸及到開關。
安裝及電源佈線必須由專業人員完成。
(產品安裝必須符合當地的安全法規。)
4
禁止對本產品進行改造。
建議兩人進行產品的安裝作業。
否則可能會導致產品損壞。
否則可能會導致產品掉落。
Otherwise, it may cause damage to
the product.
Otherwise, it may cause the
product to fall off.
It is recommended that two
persons perform the installation
of the product.
Do not reconstruct this product.
注意
CAUTION
部品安裝必須牢固。
否則可能會掉落，導致受傷。
Components must be installed
tightly.
產品必須安裝在強度足夠的窗體上，需可
承受產品5倍的重量，如不能確保安裝強
度，請務必採取加固措施。
否則可能會掉落，導致受傷。
Do not install it on window without
sufficient strength. It must be
subject to 5 times the weight of the
product. If you cannot ensure the
installation strength, be sure to
adopt reinforcement measure.
Otherwise, it may fallofforcause
personal injury.
Do fix this product tightly.
Otherwise, it may fall off or
cause personal injury.
Otherwise, it may fall off or
cause personal injury.
機體安裝必須牢固。
否則可能會掉落，導致受傷。
有安裝五金件等專用零部件時，應使
用專用零部件。
否則可能會安 裝不牢固，導致 產品
掉落。
Otherwise, unreliable installation
may be caused and thus the
product may fall off.
The special-purpose or dedicated
parts, such as mounting fixtures,
must be used if such parts are
provided.
Otherwise, a fire may be caused.
安裝注意事項
INSTALLATION INSTRUCTIONS
警告
WARNING

請勿安裝在傾斜的窗體上。
防止水倒流。
請確保整機水平安裝偏差角度在下圖所示
範圍內。
Do not install onto slanting window.
Prevent the water condensed
in the duct pipe flow back
into the body.
Pleasemakesuretheproductinstalled
horizontallyandthedeviationangle
withintherangeasbelowfigure.
5
Do not install the product in the places
where the organic solvent is used.
Maybe it can cause breakdown.
Do not install the product in steam
sauna bathroom.
Maybe it can cause breakdown.
Maybe it can cause breakdown. Maybe it can cause breakdown.
Do not install the product where it is
exposed to oil mist.
Do not install the product in the
places where the sprayer is used.
請勿安裝在桑拿蒸氣浴室中。
請勿安裝在使用噴霧器的場所。請勿安裝在油煙過多的場所。
可能會引起故障。
可能會引起故障。
可能會引起故障。
請勿安裝在使用有機溶劑的場所。
可能會引起故障。
安裝要求
Maybe it can cause breakdown.
Please set ventilation holes.
Ambient temperature
above 40 °C.
Within
50 cm
50 cm
以內
Do not install the product in places
with high temperature.
請勿安裝在高溫的環境下。
請設置通風口。
可能會引起故障。
周圍溫度 40 °C以上
The product must be installed over
1.8 m above the floor.
產品安裝高度距地面必須大於1.8 m。
The product is not provided with power cord, all-pole switch and leakage
protection switch. Please purchase them in market.
本產品沒有提供電源線，電源全極開關和漏電保護開關，需用戶另購。
INSTALLATION REQUIREMENTS

6
In extreme weather condition(rainfall precipitation more than 240 mm/h. wind speed
higher than No.8 typhoon.), there may be water through frame into bathroom.
When you install plastic part, do not exert too much strength to fixing the screw,
otherwise, the product would be damaged.
Do not install this product in a public bath room.
Do not install this product in a wardrobes.
請勿把本產品安裝在公共浴室。
請勿把本產品安裝在衣櫃內。
在極端惡劣的天氣條件下(雨量大於240 mm/h，風速大於8號風球)，可能會有水通過產品框架
進入浴室內部。
安裝塑料部件時，為了不損壞產品，鎖螺絲時請注意不要用力過大。
Product warranty registration
產品保修登記
Do not cover air outlet, maybe it can cause breakdown.
請勿覆蓋產品出風口，否則可能會引起機體故障。
安裝要求
INSTALLATION REQUIREMENTS
SUPPLIED ACCESSORIES
Installationandoperatinginstructions
Louver assembly
Remote control assembly
R03(AAA) Carbon battery
No.Drawing Nameandpurpose
Machinescrew(M4×10,usedtoinstallthelouver assembly) 1
1
1
1
1
2
2
4
Self-tappingscrew( 4×16,usedtoinstallthecontroller
holder) (placed on the backside of controller holder)
Self-tappingscrew( 4×25,usedtoinstallthe
mainbodyandthewindow)
Qty
面板組合
遙控器組合
R03(AAA)碳性電池
名稱及用途
安裝使用說明書
機械螺絲(M4×10用於面板組合安裝)
自攻螺絲( 4×25用於機體與窗體的安裝)
圖樣
代號 數量
自攻螺絲( 4×16用於遙 控器底座 安裝)(放置 於遙控器 底座背面)
包裝附件清單

8
9
1
5
2
3
4
320
180
290
298
50
270
7
部件名稱和尺寸
Unit:mm 單位：mm
No . No .
Part name Part name
Fan
AIRDIR. handle
Main body
Louver assembly
Signal receiver
Heater assembly
Baffle plate Remote control
Cord cover Filter assembly
1
9
2
10
3
11
4
5
6
7
8
序號 序號
部件名稱 部件名稱
接線蓋板
扇葉
風向調節把手
面板組合
機體
遙控器
Controller holder
遙控器底座
信號接收器
加熱器組合
導風板
過濾網
安裝俯視示意圖
離窗簾和其他易燃材料距離200 mm以上。
Install this product over 200 mm apart from
curtains or other flammable materials.
Installation diagram (Top View)
Unit:mm
Wall
Window
Bathroom
Product
單位：mm
產品
浴室
牆
窗提示事項
Notice
安裝方法
7
6
PART NAMES AND DIMENSIONS
HOW TO INSTALL
297.2
350
250
200 200
200
17
26.5
154
60
66
10
11

8
安裝方法
Add silicone to seal around the flange of
product, to make sure that the silicone cover
the entire surface of sponge.
在產品法蘭邊周圍加玻璃膠，並確保玻璃膠覆蓋整
個海綿表面。
Silicone
玻璃膠
Please be sure to take sufficient
protection measure to prevent from
high falling when install window frame.
This product is suitable for the installation of the
form of the smallest size as shown in the right
figure. A window frame needs to be made
according to the window and main body
dimensions.
It may be difficult to remove the filter if little
clearance between louver and ceiling.
Recommended main body installation method
Unit: mm
Unit: mm
單位：mm
單位：mm
Window frame material: recommend the use
of aluminum alloy.
Window frame thickness: less than 30 mm
Window frame
(Not included)
Window frame
(Not included)
Fix the window frame onto the original window.
(It must be can bear 5 times weight of the product.)
警告
WARNING
建議的機體安裝方法
窗膽材質：推薦使用鋁合金
將窗膽用可靠方法固定於原有窗框上。
(需能承受產品5倍的重量)
安裝窗膽時，請務必採取足夠的防護措施，
以防窗膽高空掉落。
窗膽厚度：小於30 mm
窗膽(另購)
窗膽(另購)
本產品適用於最小如右圖所示尺寸的窗體安裝，
請根據窗體結構及機體尺寸製作窗膽。
產品與天花板之間要確保有足夠的空間，否則
會導致產品過濾網拆卸困難。
提示事項
Notice
HOW TO INSTALL
360
25
40
40
60
Please put the lower part of the product into the
window sill first when it is installed, which to make
sure the drain does not fall off.
將機體安裝到窗膽時，先將機體下部放入窗膽并
確保排水管沒有脫落。
Drain
排水管

9
Properly install the main body according to the
direction indicating label on the main body.
Otherwise, it may cause electric leakage.
Fix the main body onto the window frame with the
supplied four 4×25 self-tapping screws.
使用附件包所提供的4顆 4×25的自攻螺絲，將機體
固定於窗膽。
請按照機體上的方向指示標籤，正確安裝產品。
否則可能會導致漏電。
Installation direction
自攻螺絲
4×25
安裝方向
4×25 self-tapping screws
Strand the core wire together after stripping,
then insert them into about 8 mm deep position
of the terminal block, ensuring that the part is
under the spring slice, and no copper core cord is
exposed outside. Make sure that the copper core
cords are fixed by screws reliably (the .
recommended screw fixing torque is 0.49 N m)
(See Figure 2). Otherwise an electric shock may
be caused.
先將剝線後分散的銅芯線絞合在一起，然後伸入到端子
台約8 mm深，並確保其在彈簧片的下方，切勿出現銅
線外露現象。螺釘擰緊後，請確保銅線不易鬆脫(建議
.
螺釘鎖緊扭矩為0.49 N m)，否則可能會導致觸電。
(右圖2)
3. Connecting power cord 電源線的連接
電源線的絕緣膠不能破損，否則可能會導致觸電或短路。
剝線長度，請按照剝線示意圖(右圖1)進行剝線，如剝線
過長，可能會導致產品短路。
電源線請選用60227 IEC 53(RVV)型軟線，導線的截
2
面積為3×1.5 mm 。
For the stripping length, please according to the
wiring sketch (refer to figure 1). If the stripping
length is too long, it may cause short circuit.
Wiring sketch
Terminal cutaway view
Conductor
Conductor
Insulation
Figure 2
Figure 1
Spring slice
Earth
Power cord
98±1
Do not damage the sheath of the power cord,
otherwise an electric shock may be caused or
short circuit.
Please select 60227 IEC 53(RVV)ordinary
polyvinyl chloride sheathed cord. Nominal
2
cross-sectional area of conductors is 3×1.5 mm .
警告
WARNING
剝線示意圖
接線柱剝面圖
Unit:mm
單位：mm
電源線
接地引線
銅芯線
銅芯線
絕緣膠
彈簧片
(圖2)
(圖1)
警告
WARNING
安裝方法
HOW TO INSTALL
5

提示事項
Notice
提示事項
Notice
10
Install an all-pole switch with the contact separation
not less than 3 mm and a leakage protection switch
(with the leakage current lower than 30 mA)between
the fixed wring and the main body of this product.
請於固定佈線與本產品主機間安裝觸點開距不小於3 mm的
“電源全極開關”及漏電保護開關(洩漏電流在30 mA以下)。
漏電 保護 開關(另 購)
固定 佈線
本產品 主機
電源 全極 開關
將固定電源線線夾的螺絲鬆脫。
螺絲
線夾
Remove the screws (2 pcs) on the cord
cover, and open the cord cover and the
internal cord cover (by pushing the
clamping position outward).
取下接線蓋板上的螺絲(2顆)，
打開接線蓋板及內接線蓋板。
請根據當地相關的電力線路規範選擇合適的“電源全極開
關”和“漏電保護開關”。
Screw
Cord clip
Cord clip
Screws (2 pcs)
固定螺絲(2顆)
打開後示意圖
Please select the suitable all-pole switch and leakage
protection switch according to locally relevant
Electricity and Wiring Regulations .
Loosenthescrewsofthecordclip.
Diagram with the cover removed
Fix the power cord with the cord clip.
(The cord clip must pin the insulation
sheath of power cord.)
As shown in Figure 1 of P9
用電源線線夾將電源線固定。
(電源線線夾必須壓住電源線的絕緣護套)
如第9頁圖1所示
線夾
Loosen the screws of the pillar terminal,
insert the power cord (not supplied)
connected to the indoor fixed wiring into
the pillar terminal, tighten the screw, and
guide the wire according to the right figure.
鬆開接線柱上的螺絲，將接入室內固定線路的電
源線(用戶自購)插入接線柱，擰緊接線柱螺絲，
並按右圖進行理線。
安裝方法
HOW TO INSTALL
接線蓋板
內接線蓋板
Cord cover
Internal
cord cover
Before opening the cord cover, Please read
the label content first, then remove the
warning label.
打開接線蓋板前，請先閱讀標籤內容，再把粘貼在
其上方的警告標籤撕掉。
Insulation
sheath
絕緣護套