Panasonic PAW-500ZDX3N User manual
MANUALE DI INSTALLAZIONE USO E MANUTENZIONE
INSTALLATION, USE AND MAINTENANCE MANUAL
UNITÀ DI RECUPERO CALORE
CON BATTERIA A ESPANSIONE DIRETTA
ENERGY RECOVERY VENTILATION
UNIT WITH DX COIL
ERV+DX
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 1
nstallation, Use and Maintenance Manual - ERV+DX series pag. 19
English
page 20
page 21
page 22
page 22
1.1 Presentation of the manual page 23
1.2 General characteristics page 23
1.3 ERV+ X series technical data page 23
1.4 imensions and weights page 24
2.1 Packing page 25
2.2 Handling and transport page 25
2.3 Control upon reception page 25
2.4 Storage page 25
3.1 efinitions page 25
3.2 safety standards page 25
3.3 Preliminary operations page 26
3.4 Choice of the installation place page 26
3.5 Positioning of the machine page 27
3.6 rain tray connection page 27
3.7 Connection to the ducts page 27
3.8 Connecting the refrigerant tubing page 28
4.1 Remote control installation and working page 30
4.2 Wiring diagram page 31
page 31
6.1 Attentions page 32
6.2 Monthly controls page 32
6.3 Yearly controls page 33
page 34
page 34
page 35
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 19
English
DECLARATION OF CONFORMITY
SIC s.r.l. Società Unipersonale
Company
Viale dell’Industria, 25 37044
VR
Address Zip Province
Cologna Veneta
I
taly
City State
DECLARES UNDER ITS OWN RESPONSIBILITY THAT THE MACHINERY
Heat Recovery Unit
E
RV+DX
Description
Series
ERV
+
DX PA
W
– 500 ZDX3N; ERV
+
DX PA
W
– 800 ZDX3N; ERV
+
D
X
PA
W
–
01
KZDX3N
Models
Double flow mechanical ventilation with static, cross flow enthalpic heat exchange
r
and direct expansion coil
Function
Heat Recovery Unit ERV+DX Series
Commercial name
ARE IN COMPLIANCE WITH THE FOLLOWING DIRECTIVES
Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery;
Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the approximation of the laws of the
Member States relating to electromagnetic compatibility;
Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of
Member States relating to electrical equipment designed for use within certain voltage limits;
Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of hazardous
substances in electrical and electronic equipment (RoHS 2);
Directive 2012/19/EU of the European Parliament and of the Council of 4 July 2012 on waste electrical and electronic equipment
(WEEE);
Commission Regulation (EU) 1253/2014 implementing Directive 2009/125/EC regarding the specific eco-design of the ventilation
units;
AND AUTHORIZES
Andrea Mantovani
Name
Viale dell’Industria, 25 37044
VR
Address Zip Province
Cologna Veneta
I
talia
City State
TO COMPILE THE TECHNICAL FILE
In case of improper use or unauthorized modification of the machinery equipment, this document will loose its validity. It is forbidden to put the unit that is object
of this declaration in service before the machine or the plant in which the machine will operate is in compliance with the dispositions of Machinery Directive
2006/42/EEC and following modifications.
Cologna Veneta, 09th January 2018
THE GENERAL MANAGER
ANDREA MANTOVANI
SIC srl Società Unipersonale
Viale dell’Industria, 25 – 37044 Cologna Veneta VR Italy – Tel. +39 0442 412741 Fax +39 0442 418400 – www.sicsistemi.com - info@sicsistemi.com
DK>>KDK>
DdZ/K>^Z/>EhDZ
dK>>hKd^d/E'd
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 20
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 20
This manual is an integral part of the apparatus and then it must be preserved with care and it ALWAYS must accompany the machine, even in the
case of cession to another owner or user or in the case of a transfer on another system. In the case of its damage or losing, ask another copy to
the distributor Company.
The repairs or the maintenance must be carried out by expert and qualified staff as it is expected in this handbook. on’t modify or tamper with the
machine because it can create dangerous situations and the distributor Company does not answer to possible damages.
Check the perfect integrity of all ERV+ X components. Check that in the packing all the accessories for the installation and the relevant documen-
tation, are included. In the case of not conformity turn to seller company.
The installation of the machine must be carried out by qualified Company according to the law March, 5th 1990 n° 46 which, at the end of the work,
must give to the owner, the declaration of conformity of installation workmanlike, that is in compliance with the regulations in force and with the indi-
cations of this handbook.
The distributor Company does not answer to possible damages to people, animals or things, due to wrong installation, regulations and maintenance
or due to illegitimate use.
Remember that in the use of products that use electrical energy and water, some fundamental rules of security must be observed.
In particular:
Children and handicapped people without assistance must not use the machine.
on’t touch the machine if you are barefoot and if you are wet.
o not proceed with cleaning or maintenance operations, before switching off the electric power supply.
o not modify security or adjustement devices without permission and indications of the Manufacturer Company.
o not pull, remove, twist electrical cables coming out from machine, even if these is disconnected from power supply network.
o not walk up, sit down and/or place any objects on the machine.
o not spurt water directly on the machine.
o not open access doors of the machine, without positioning general switch of the system on "off" .
o not scatter, leave close by children packing material because it could be dangerous.
English
nstallation, Use and Maintenance Manual - ERV+DX series pag. 21
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 21
English
B
A
C
D
E
F
G
H
I
L
Manufacturer's mark
Manufacturer's address
Model
Serial number
Voltage; number of phases; frequency
Maximum absorbed current [A]
Code
Manufacturing date
CE mark
Barcode
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 22
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 22
English
This manual describes the rules for the transportation, the installation, the use and the maintenance of the heat recovery. The user will find every-
thing that is normally useful to know for a correct and safe installation of the ERV+ X unit.
The non-observance of what is described in this handbook and an inadequate installation of the ERV+ X unit may cause the cancellation of the
guarantee that the Manufacturer/ istributor Company grants on the same one. The Manufacturer/distributor Company, moreover, does not
answer to possible direct and/or indirect damages due to wrong installation carried out by inexpert and/or non-authorised staff. At the moment
of the purchase, check that the machine is integral and complete. Claims will have to be produced within 8 days from the reception of the goods.
• Galvanized steel self-supporting panels, internally and externally insulated
• Counterflow air-to-air heat recovery device, made of plane sheets of special paper with special sealing to keep airflows separate and only
permeable to water vapor. with temperature efficiency up to 76% and enthalpy efficiency up to 67%, also at high
level during summer season
• ISO 16890 Coarse 50% + ePM2.5 95% (F9 EN779) efficiency class filters on fresh air, Coarse 50% (G3 EN779) filer on return air intake. All
filters are made with synthetic cleanable media.
• Removable side panel to access filters and heat recovery in the event of scheduled maintenance
• Motorised heat recovery by-pass device automatically controlled by unit control to use fresh air free-cooling when convenient
• , high efficiency & low noise direct driven fans with
• (R410A) fitted with solenoid control valve, freon filter, contact temperature sensors on liquid and gas
line, NTC sensors upstream and downstream airflow
• , switched on at fans running, able to do an efficient antibacterial treatment, ensuring a perfect healthi-
ness of supplied air
• Built-in electric box equipped with PCB to control internal fan speed and to interconnect outdoor/indoor units
• uct connection by circular plastic collars
Portata aria nominale / Nominal air flow m3/h 500 800 1000
Pressione statica utile nominale / Nominal external static pressure Pa 90 120 115
Alimentazione elettrica /Electrical power supply V/ph/Hz 230 / 1 / 50 - 60
Corrente assorbita massima totale /Total full load amperage A 0.6 1.4 2.1
Condizioni di esercizio limite / Limit working temperature °C / % - 15 …+ 40°C / 10 … 95 %
Tipologia motore / Motor typology EC EC EC
N° velocità / Number of speeds 33 3
Controllo ventilazione / Fan control (1) Man Man Man
Potenza specifica interna di ventilazione - SFP int /
nternal specific fan power of ventilation components - SFP int (5) W/(m3/s) 547 865 881
Potenza assorbita nominale totale / Total nominal power input kW 0.15 0.32 0.39
Livello di pressione sonora / Sound pressure level (2) dB(A) 39 42 43
Efficienza termica invernale / Winter thermal effic. (3) % 76.0% 76.0% 76.0%
Efficienza entalpica invernale / Winter enthalpy effic. (3) % 67.0% 65.0% 62.0%
Efficienza termica estiva / Summer thermal effic. (4) % 76.0% 76.0% 76.0%
Efficienza entalpica estiva / Summer enthalpy effic. (4) % 63.0% 63.0% 60.0%
Efficienza termica a secco / Dry thermal efficiency (5) % 76.0% 76.0% 76.0%
Potenza termica / Heating capacity (6) kW 2,5 (2,7) 4,4 (4,8) 5,2 (6,7)
Temperatura aria mandata / Supply air temperature °C 28,0 (27,3) 29,6 (29) 28,5 (27,8)
Umidità aria mandata / Supply air humidity % 16 (15) 14 (13) 15 (14)
Potenza frigorifera totale / Total cooling capacity (7) kW 3.0 5.1 5.8
Potenza frigorifera sensibile / Sensible cooling capacity kW 2.1 3.5 4.1
Temperatura aria mandata / Supply air temperature °C 15.9 15.5 16.2
Umidità aria mandata / Supply air humidity % 90 90 89
nstallation, Use and Maintenance Manual - ERV+DX series pag. 23
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 23
English
Main PCB box
X Coil check
Fan PCB box
1495 1395 1705 880 960 1000 270 500 358 200 135 90 / 98 1700 x 1120 x 420
1685 1685 1870 1125 1190 1230 390 678 446 250 170 100 / 110 1960 x 1380 x 540
1700 1700 1870 1215 1270 1320 390 621 552 250 190 105 / 120 2080 x 1460 x 540
(1) Multiple = Multispeed > 3
Man = Manual by selector switch or control panel; 0-10V = By potentiometer or control panel; VSD = Modulation by air quality or air humidity
sensor
(2) Sound pressure level calculated at 1 m far from: ducted supply-exhaust air/ducted
return-fresh air intake/service side, at nominal conditions.
(3) Outside air at -5° 80% RH; room air at 20°C 50% RH
(4) Outside air at 32° 50% RH; room air at 26°C 50% RH
(5) Refeer to EU 1253/2014 regulation: at nominal pressure; air conditions refer to EN 308 standard
(6) Air inlet condition: 13°C DB, RH 40% (11°C DB, RH 45%); condensing temp. 40°C
(7) Air inlet condition: 28,5°C DB, RH 50%; evaporating temp. 7°C
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 24
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 24
English
• The regenerators and their accessories are inserted in cardboard boxes that will have to remain integral until the moment of the assembly.
• The components that, due to technical requirements, are not assembled, are supplied packed in a suitable covering and fixed to the inside or
outside of the unit.
• For the handling, in function of the weight, use adequate means in conformity to the directive 89/391/EEC and successive modifications.
• The weight of every single machine is shown on the attached technical data sheet.
• Avoid rotations without control.
• Take utmost care during loading operations: all the machines must be loaded and stored in the truck interposing opportune spacers to safe-
guard all protruding parts like water couplings, handles, hinges.
Upon reception of the goods, please carry out a control of all the parts, verifying that the transport has not caused damages. All damages must
be communicated to the carrier, putting a reserve clause on the delivery note and specifying the type of damage.
In case of long term storage, keep the machines protected from dust and from all sources of vibrations and heat.
- The customer is the person, the agency or the company, that has acquired or rented the unit and that uses it for the conceived
purpose.
- The operator or user is the physical person who has been authorised from the customer to operate with the machine
- Intended are all those physical persons who have achieved a specific training, are therefore in a position to recognize
the dangers deriving from the use of this machine and are able to avoid them.
The Manufacturer/ istributor Company declines whichever responsability for the non observance of the emergency and prevention norms
described below.
It declines furthermore responsibility for damages caused by an improper use of the unit and/or by modifications carried out without authoriza-
tion.
• The installation must be carried out by expert and qualified staff.
• uring installation operations, use suitable accident-prevention clothing, as an example: glasses, gloves, etc as indicated by the 686/89/EEC
and successive norms.
• uring installation, operate in absolute safety, in clean surrounding and free from impediments.
• Respect the laws in force in the Country in which the unit is installed, concerning the use and the disposal of the packings and the products
used for cleaning and maintainig the machine and follow the manufacturer instructions of such products.
• Before putting the unit in function, check the perfect integrity and safety of all components and of the entire system.
• Avoid at all cost to touch the parts in motion or to intefere with the same ones.
• o not proceed with cleaning or maintenance operations, before switching off the electric power supply.
• The maintenance and the substitution of damaged or worn out parts of the unit must be carried out by qualified staff only and following the
indications contained in this handbook.
nstallation, Use and Maintenance Manual - ERV+DX series pag. 25
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 25
English
• Spare parts must correspond to the requirements defined by the Manufacturer Company.
• In case of dismantling of the unit, follow the relevant antipollution norms.
N.B. When using the unit, the installer and the user must take into account and place remedy to all the other types of risk connected with the
sistem. As an axample risks deriving from entry of foreign bodies, or risks deriving from the conveying of dangerous gases that are inflamma-
ble or toxic at high temperature.
.
• Check the perfect integrity of all components.
• Check that in the packing all the accessories for the installation and the relevant documentation, are included.
• Transport the packed section as close as possible to the installation place.
• o not put tools or weights over the packed unit.
• Place the unit on a solid structure that shall not causes vibrations and that is solid enough to support the weight of the machine.
• o not place the unit in rooms where inflammable gases, acids or aggressive and corrosive substances may be present. These could dama-
ge the different components in an irreparable way.
• Foresee a minimum free space as shown on the following figures, to make possible the carrying of scheduled and not scheduled maintenan-
ce; in order to do maintenance to Bioxigen system, allow accessibility from lower side around supply section with X coil.
450 450 450
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 26
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 26
English
In the continuation are illustrated some sequences of the
assembly:
1. Carry out the drilling on the ceiling and fix six M8
threaded rods as shown in the figure.
2. Position the unit on the six threaded rods (eight brac-
kets available).
3. Block the unit by locking the bolts.
• The ducts must be dimensioned in function of the system and of the air flow characteristics of the unit ventilators. A wrong calculation of the
ducts may cause loss of power or the possible activation of devices fitted on the unit.
• Severe bending, several bending and diameter reductions of the ducts should be avoided to minimize the pressure loss.
• In order to prevent the formation of condense and to reduce the noise level it is advised to use insulated ducts.
• If rigid ducts are used, to avoid the transmission of possible vibrations of the machine in the atmosphere, it is advised to interpose an antivi-
brating joint between the air outlets and yhe ducts. The electrical continuity between duct and machine must however be guaranteed through
a earth cable.
• The distance between indoor inlet port and indoor intake port should be as far as possible
• In order to prevent the penetrations of rains, the ducts connecting the unit with the outside should be protected by grilles.
Moreover the ducts should be a little tilted
Exhaust air
duct
Indoor Intake
duct
Room intake
opening
Supply air duct
Threaded rods (min 6)
Outside
intake air
Outside intake duct
Brackets
Inside supply
opening
Close to supply air duct connection, a drain tray outlet
(1/4” hose pipe) shall be connected for discharge of con-
densed water during cooling mode.
It is strongly suggested to install a water trap close to
the unit in order to avoid odors coming inside and to get
a slope on discharge pipeline.
nstallation, Use and Maintenance Manual - ERV+DX series pag. 27
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 27
English
The unit is supplied with plugged direct expansion coil: to ensure its tightness during storage and
transport, inside it is loaded nitrogen gas at a higher pressure than atmospheric.
Nitrogen is sealed inside the main unit. Before loosening the flare section, perform the fol-
lowing airtightness check. Use pliers or a similar tool to bend the end of the indoor unit hermetically
sealed tubing so that a crack is formed. Verify that a “pffft” sound occurs.
Unscrew the flare caps.
Cut the copper tube to the required length with a tube cutter. It is recommended to cut approx. 30 – 50 cm longer than the tubing length•
you estimate.
Remove burrs at each end of the copper tubing with a tube reamer or file. This process is important and should be done carefully to•
make a good flare. Be sure to keep any contaminants (moisture, dirt, metal filings, etc.) from entering the tubing.
Remove the flare nut from the unit and be sure to mount it on the copper tube.•
Make a flare at the end of the copper tube with a flare tool. A good flare should have the following characteristics:•
- inside surface is glossy and smooth
- edge is smooth
-tapered sides are of uniform length
Apply a sealing cap or water-proof tape to prevent dust or water from entering•
the tubes before they are used.
Be sure to apply refrigerant lubricant (ether oil) to the inside of the flare nut•
before making piping connections. This is effective for reducing gas leaks.
For proper connection, align the union tube and flare tube straight with each•
other, then screw on the flare nut lightly at first to obtain a smooth match.
Adjust the shape of the liquid tube using a tube bender at the installation site•
and connect it to the liquid tubing side valve using a flare.
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 28
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 28
English
Replace air inside the tube with nitrogen gas to prevent copper oxide film from forming during the brazing process. (Oxygen, carbon dioxide
and Freon are not acceptable.)
o not allow the tubing to get too hot during brazing.The nitrogen gas inside the tubing may overheat, causing refrigerant system valves to
become damaged. Therefore allow the tubing to cool when brazing.
Use a reducing valve for the nitrogen cylinder.
o not use agents intended to prevent the formation of oxide film. These agents adversely affect the refrigerant and refrigerant oil, and may
cause damage or malfunctions.
In the table below are shown the pipes diameter for each unit
For the flare nuts at tubing connections, be sure to use the flare nuts that were supplied with the unit, or else flare nuts for R410A. The refrige-
rant tubing that is used must be of the correct wall thickness as shown in the table below.
Because the pressure is approximately 1.6 times higher than conventional refrigerant pressure, the use of ordinary flare nuts or thin-walled
tubes may result in tube rupture, injury, or asphyxiation caused by refrigerant leakage.
In order to prevent damage to the flare caused by overtightening of the flare nuts, use the table above as a guide when tightening.
When tightening the flare nut on the liquid tube, use an adjustable wrench with a nominal handle length of 200 mm.
Thermal insulation must be applied to all units tubing, including distribution joint (field supply). For gas tubing, the insulation material must be
heat resistant to 120°C or above. For other tubing, it must be heat resistant to 80°C or above.
Insulation material thickness must be 10 mm or greater.
If the conditions inside the ceiling exceed B 30°C and RH 70%, increase the thickness of the gas tubing insulation material by 1 step.
Gas Pipe ø 12,7 mm
Liquid Pipe ø 6,35 mm
ø 6,35 (1/4”) 14 - 18 N*m 0,8 mm
ø 12,7 (1/2)” 49 - 55 N*m 0,8 mm
nstallation, Use and Maintenance Manual - ERV+DX series pag. 29
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 29
English
• The electrical connections to the control cabinets must be carried out by specialized staff, following the supplied wiring diagrams.
• Make sure that the voltage and the frequency specified on the nameplate correspond to those of the power supply line.
• For the main supply of the regenerator is not allowed to use adapters, multiple sockets and/or cable extensions.
• Connect the unit to an effective earth, using the appropriate screw fitted on the unit.
• The remote control panel is suitable for wall mounting
• To mount:
- unlock the rear cover (locked by plastic tooth) and fix it to the wall using
the prearranged holes
- lock the main body to the rear cover fixed on the wall
• Connect the two wires to R1-R2 terminals inside the electrical box in the supply
section with X coil
1) Switch on/stand-by button
2) Mode selection button
3) Fan speed selection button
4) Unit selection button (in case of multi-machine)
5) Clock program buttons
6) Filter check reset button
Instructions for use and setting are explained in the specific manual supplied
together the remote controller.
• The remote control panel is suitable for wall mounting (exposed or embedded
type)
• Unlock the rear cover (locked by plastic tooth) and fix it to the wall using the
prearranged holes
• Pass the cables through specific holes and connect the two wires to R1-R2 ter-
minals inside the electrical box in the supply section with X coil
Lock the main body to the rear cover fixed on the wall•
1) Switch on/stand-by button
2) Operation indicator: illuminates during operation, blinks during alarm
3) Cross key buttons: selects an item
4) Menu button: displays the menu screen
5) Enter button: fixes the selected content
6) Return button: returns to the previous screen
7) Energy saving button: switches Energy saving / Normal operation
Instructions for use and setting are explained in the specific manual supplied
together the remote controller.
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 30
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 30
English
Before starting the unit check the following:
• Anchorage of the unit to the ceiling.
• Connection of the air ducts.
• Connection of the earth cable.
• Fixing of all the electric terminals.
Scheda principale
ERV+DX
ERV+DX main PCB
LN
Consenso unità esterna
Outdoor unit signal
Pannello remoto
Remote control panel
AT
Sonda Aria
ingresso
batteria /
Air probe
coil in
TBL
Sonda Aria
uscita batteria/
Air probe
coil out
E1
Sonda Aria
ingresso
refrigerante /
Air probe
refrigerant in
E3
Sonda Aria
uscita refrigerante/
Air probe
refrigerant out
L = linea / line
N = neutro / neutral
PE = terra / protective earth
LINEA ALIMENTAZIONE: PREDISPORRE A MONTE UNA ADEGUATA PROTEZIONE
CON INTERRUTTORE MAGNETOTERMICO DIFFERENZIALE / POWER LINE: PROVIDE A
PROPER SAFETY DEVICES EQUIPPED WITH DIFFERENTIAL MAGNETOTHERMAL SWITCH
A TRATTEGGIO SONO RAPPRESENTATI I
COLLEGAMENTI DA EFFETTUARSI A CURA
DELL'INSTALLATORE DASHED LINES SHOW THE
CONNECTIONS TO BE CARRIED OUT BY THE
INSTALLER
exhaust fan
supply fan
Bioxigen (option)
Pressostato differenziale
(Filtri sporchi)
nstallation, Use and Maintenance Manual - ERV+DX series pag. 31
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 31
English
• It is a duty of the user to carry out all the maintenance operations on the regenerator.
• Only assigned and previously trained and qualified personnel can carry out maintenance operations.
• If the unit must be disassembled, protect hands with gloves.
After cleaning, repeat the operation sequence in reverse order.
Vacuum cleaner
Heat exchangers
Filter Filter
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 32
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 32
English
• Verification of the whole electrical installation and in particular the tightening of the cable connections.
• Verification of the tightening of all bolts, nuts, flanges and water connections that could be loose because of vibrations.
Once a year at least or when a drop in purifying efficiency is felt cleaning of capacitor shall be done.
In order to service Bioxigen system, following instructions shall be carried out :
• Switch off the whole unit (main power supply off)
• Unscrew the 4 fixing screws of Bioxigen system, operating from the lower side of the unit close to supply air duct connection
• rop off the module (accomodating its fall) until the quartz capacitor is fully out of the unit
• Unlock the electric connector
• After laying the module on a flat surface, unscrew carefully the quartz capacitor ()
• Remove the external net (); if it should be difficult, rotate it lightly around the capacitor
• Clean the capacitor with a wet cloth.
• Wash the net with a jet of hot water and dry thoroughly with a dry cloth
• If the pipe is damaged, it shall be replaced with a new one
• As soon as a whitish layer is over the metal grille inside the pipe, capacitor shall be replaced. Usual time for replacement is 18-24 months
• Fit the net on the pipe and over the internal grille.
• Check that tab ( ) is in contact with the metal net and push it against the glass of the capacitor ()
• Clean the equipment all around outside
• Screw softly the capacitor in its seat
• Insert the module across the lower hole and lock the electric connector
• Screw the fixing screws
• Check if the system is working. Now a light noise might be audible.
nstallation, Use and Maintenance Manual - ERV+DX series pag. 33
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 33
No power supply.
The switches of the thermostat are not in the right position of working.
There are foreign bodies that block the rotors.
Electrical connections are released.
Too low airflow.
Insufficient refrigerant fill (check refrigerant circuit).
Compressor off (check outdoor condenser unit).
Pressure drop of the system are overvalued.
Pressure drop of the system are underestimated.
Cloggings in the air ducts.
Rotation speed too low: verify on the terminal board of the motor that the connection is correct and that the volta-
ge correspond to that of the nameplate.
The rotor turn backwards.
Excessive air flow.
Wear or crack in the pads.
Unbalanced fan.
Foreign bodies in the case.
Unbalanced impeller because of wear or of dust deposit.
Sliding of the impeller on the case due to deformations.
Cloggings in the air ducts
English
nstallation, Use and Maintenance Manual - ERV+DX series
pag. 34
This symbol indicates that this product must not be disposed of with household waste. Dispose of the unit properly according
to local laws and regulations.
When the unit reaches the end of its useful life, contact the authorities for information on disposal and recycling possibilities;
alternatively, it will be possible to request the free collection of the used equipment from the manufacturer.
Separate collection and recycling of the product at the time of disposal will help and conserve natural resources and ensure
that the unit is recycled in a manner that protects human health and the environment.
AEE registry code: T16070000009428
The materials that compose this heat recovery units are:
• Galvanized plate
• Alluminium
• nox
• Quartz glass
• EPS (expanded polystyrene)
• Polyethylene
• ABS plastic (acrylonitrile butadiene styrene)
• NBR (nitrile butadiene rubber NBR)
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 34
English
CF0P30MICH050050 CF0M90MICH050480
CT00000MICEH0250
MV00BOC0MICH0500 MTE00000MICH0500 VT000GIRMICH0500 PR000E000MICH050
QE1CV62331675890
CF0P30MICH080050 CF0M90MICH080480 MV00BOC0MICH0800 MTE00000MICH0800 VT000GIRMICH0650 PR000E000MICH080
CF0P30MICH100050 CF0M90MICH100480 MTE00000MICH1000 VT000GIRMICH0100 PR000E000MICH100
BTAECV0400J02NO0 FRSV02S50 NC1000
C 0037C185000000 ME4CV62332100250
ME4CV62332099990 ME4CV62332100010 ME4CV62332100180 ME4NTCMICROE0000 MV00BYP0MICH0000
BTAECY0550J03RO0 FRSV02S80 NC1000
nstallation, Use and Maintenance Manual - ERV+DX series pag. 35
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 35
Viale dell’Industria, 25
37044 Cologna Veneta (Verona) Italy
tel. +39 0442 412741 - fax +39 0442 418400
E-mail: [email protected] - www.sicsistemi.com
DC MAN I 05 460 ERVDX 09_SIC 14/01/2019 17.05 Pagina 36
This manual suits for next models
5
Table of contents
Other Panasonic Fan manuals
Panasonic
Panasonic FV-30BW2H User manual
Panasonic
Panasonic FV-40BE2H User manual
Panasonic
Panasonic FV-24JR2 User manual
Panasonic
Panasonic F-48DFL User manual
Panasonic
Panasonic F-M15F1 User manual
Panasonic
Panasonic RG-T810LA User manual
Panasonic
Panasonic EcoVent FV-07VBA1 User manual
Panasonic
Panasonic F-BR251 User manual
Panasonic
Panasonic WhisperSense FV-08VQC5 User manual
Panasonic
Panasonic Whisper Green FV-05VK1 User manual
Panasonic
Panasonic FV-10NLF1E User manual
Panasonic
Panasonic RG-T810HA User manual
Panasonic
Panasonic WhisperSense FV-08VQCL6 User manual
Panasonic
Panasonic ECONAVI F-M15H5VBSQH User manual
Panasonic
Panasonic F-56MPG User manual
Panasonic
Panasonic FV-05-11VKSL1 User manual
Panasonic
Panasonic FV-40NLF1 User manual
Panasonic
Panasonic Intelli-Balance 100 User manual
Panasonic
Panasonic WhisperGreen FV-08VKML3 User manual
Panasonic
Panasonic FV-08VRL1 User manual
Popular Fan manuals by other brands
Sinbo
Sinbo SF 6713 instruction manual
L.B. White
L.B. White 24D370 owner's manual
CFM
CFM SEF Installation & maintenance instructions
Caryaire
Caryaire LVLS Installation and maintenance manual
Helios
Helios SilentBox SB Series Installation and operating instructions
Monte Carlo Fan Company
Monte Carlo Fan Company 5MMR54 Series owner's manual
impress
impress iM-783 Use and care book
Monte Carlo Fan Company
Monte Carlo Fan Company 5AHR60 Series owner's manual
Hunter
Hunter 23949 Owners and installation manual
Monte Carlo Fan Company
Monte Carlo Fan Company MC263 Series Owner's guide and installation manual
Monte Carlo Fan Company
Monte Carlo Fan Company 3ROZR52 Series Owner's guide and installation manual
Exhale Fans
Exhale Fans EF34 Owner's guide and installation manual