Panasonic EH-KA11 User manual

© Panasonic Electric Works (Thailand) Co., Ltd.
2009. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PEWT0909A80CE
Hair Styler
Model No. EH-KA11
Asia
Middle East
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 6
6 Schematic Diagram ---------------------------------------------- 8
7 Exploded View and Replacement Parts List ------------ 9

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
(Refer to SCHEMATIC DIAGRAM and WIRING CONNECTION DIAGRAM.)

4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
1. Remove the two Torx screws from the escutcheon, then
remove the escutcheon, the filter and the fixing ring.
2. Separate the housing A and B by unfastening the hook.

5
4.2. Caution In Assembly
Refer to WIRING DIAGRAM to solder the wires.
1. Attach the lead wires (red for main switch and yellow for
heater) to the rectifier block from bottom. Then install rec-
tifier block on the motor block with capacitor by soldering
as shown in Figure.
2. Install the main switch on the motor block, and then insert
the black lead wires between ribs tightly. Do not allocate
the lead wires on the main switch.
3. Install the push button with coil spring and the arm switch
plate with switch plate on the housing B.
4. Install the heater motor block on the housing B. Then
insert the black lead wires between ribs.
5. Install the air inlet ring and power cord on the housing B.
6. Install the connector cover A on the housing A.
7. Put the housing A and B together.
8. Attach the filter, fixing ring and the escutcheon to the
housing.

6
5 Wiring Connection Diagram
5.1. Wiring Connection Diagram for 110V

7
5.2. Wiring Connection Diagram for 220-240V

8
6 Schematic Diagram

Model No. : EH-KA11 Exploded View
7 Exploded View and Replacement Parts List

Model No. : EH-KA11 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 EHKA11HSW1W HOUSING AB 1 (FOR TAIWAN)
1 EHKA11HSW2W HOUSING AB 1
1 EHKA11HSW7W HOUSING AB 1 (FOR KOREA)
2 EHKA11FTWSW FILTER 1 (FOR TAIWAN, VIETNAM, INDIA, IRAN)
2 EHKA11FTWBW FILTER 1
3 EHKA11FRHW FIXING RING 1
4 EHKA11CTBW CONNECTOR COVER B ASS'Y 1
5 EHKA11CTAW CONNECTOR COVER A 1
6 EHKA11PCHA2W POWER CORD 1 (A-2 PLUG)
6 EHKA11PCHS3W POWER CORD 1 (BF-3 PLUG)
6 EHKA11PC615W POWER CORD 1 (B-2 PLUG)
6 EHKA11PC675W POWER CORD 1 (KS PLUG)
7 EHKA11AIRTW AIR INLET RING 1
8 EHKA11MB1W MOTOR ASS'Y 1 (FOR TAIWAN)
8 EHKA11MB2W MOTOR ASS'Y 1
9 EHKA11MSW MAIN SWITCH 1
10 EHKA11ITBW INSULATION TUBE 1 (4PC/PK)
11 EHKA11ASPNW ARM SWITCH PLATE 1 YELLOW
12 EHKA11HB1W HEATER B/K ASS'Y 1 (FOR TAIWAN)
12 EHKA11HB2W HEATER B/K ASS'Y 1
12 EHKA11HB6W HEATER B/K ASS'Y 1 (FOR SAUDI ARABIA)
13 EHKA11RFBW RECTIFIER ASS'Y BLOCK 1
14 EHKA11CSHW COIL SPRING 1
15 EHKA11PBWW PUSH BUTTON 1
16 EHKA11MSPWW MAIN SWITCH PLATE 1
17 EHKA11T2604W TORX SCREW 2 (M2.6-4)
18 EHKA11ESW ESCUTCHEON 1
19 EHKA11HTWW BLOW BRUSH ASS'Y 1
- EHKA1113501W INDIVIDUAL PACKAGE 1 (FOR TAIWAN)
- EHKA1161501W INDIVIDUAL PACKAGE 1 (FOR VIETNAM, INDIA, IRAN)
- EHKA1165501W INDIVIDUAL PACKAGE 1 (FOR MALAYSIA)
- EHKA1166501W INDIVIDUAL PACKAGE 1 (FOR SAUDI ARABIA)
- EHKA1167501W INDIVIDUAL PACKAGE 1 (FOR KOREA)
- EHKA1168501W INDIVIDUAL PACKAGE 1 (FOR SINGAPORE, HONG KONG, KUWAIT)
- EHKA11S03UW INSTRUCTION BOOKLET 1
- EHKA11S09W FILLER FOR PACKAGE 1