Panasonic VL-SWD501 User manual

2013 Wireless Video Intercom
INSTALLATION GUIDE

System
System configuration and wiring configuration and wiring
VL-SWD501 System Component
VL-SWD501EX wiring schematic diagram
VL-SWD501EX wiring type and length
Door Station
Door Station Installation Installation
Installing the door station (VL-V554EX)
Installing the door station (VL-V554UEX)
Door station installation position
Main
Main Monitor Station Installation Monitor Station Installation
Installing the main monitor station
Main monitor station installation position
Power Supply Unit
Power Supply Unit Installation Installation
Installing the power supply unit (VL-PS241)
Initial Setup
Initial Setup
Setting the date and time
Changing the date and time
Setting Demo mode
Registering wireless monitor stations
Installing Wireless Sensor Cameras
Installing Wireless Sensor Cameras
Install the wireless sensor camera
If connecting an external sensor
Using external sensor (About the external input terminal )
Wire type and length
Installation location for the wireless sensor camera
Registering the wireless sensor camera to the main monitor station
Viewing wireless sensor camera images
( Monitoring the out side with the wireless sensor camera)
Registering DECT repeaters
Registering DECT repeaters
Registering DECT repeaters to the main monitor station
Cancelling
Cancelling
Cancelling wireless monitor stations,
wireless sensor cameras, DECT repeaters
Specifications
Specifications
Main Monitor Station
Power Supply Unit
Door Station
Wireless Monitor Station (Main body)
Wireless Monitor Station (Charger)
Wireless Sensor Camera
DECT Repeater
…….………………………. 4
………….....… 5
………….……..…. 6
…….........…..… 8
……........….. 10
…………………………. 12
……………..………. 17
……......…. 19
…......…. 21
……………...………..………… 24
…………………..………….. 25
……………………..….………………… 26
………..………. 27
..………………………………… 29
…..…………..…………………….. 31
……….. 33
………………………………………………….……… 34
............ 35
.. 36
…………………………….. 38
………. 41
…….…… 43
………………………………………………………. 45
………………………………….……………………… 46
………………………………………….………………………. 47
……………………………… 48
…………………………………… 49
…………………………………………………… 50
………………………………………….………..……..……. 52
INDEX
INDEX

System configuration and wiring
System configuration and wiring

VL
VL- -SWD501 System Component SWD501 System Component
5-inch
wide screen
touch panel 2.2-inch TFT
colour LCD
Wireless
Monitor Station
(Sub monitor)
VL-WD613
Up to
2
DECT
Repeater
VL-FKD2
Up to
2Up to 4
Up to
6
Door Station
(Doorphone)
Door Station
(Doorphone)
VL-V554
Main Monitor Station
(Main monitor) Wireless Monitor Station
(Sub monitor)
Wireless
Sensor Camera
VL-WD812
Basic System Component
Optional Expandability
VL-SWD501

5
6
Power
supply
Power
supply
Power
supply
Power
supply
NP
NP NP
NP
NP
NP
NP
NP
Electric lock
(Electric vehicle gate lock)*1
12 VAC/DC
12 VAC/DC
12 VAC/DC
12 VAC/DC
220-240 VAC
24 V DC
Electric lock
(Electric vehicle gate lock)*1
Electric lock
(Electric door lock)*2
Electric lock
(Electric door lock)*2
DA
D
E
B
C
Connection device for option
output (A contact)
*1 Make sure to only connect electric vehicle gate locks to the S3/S4
terminals of the door stations.
*2 Make sure to only connect electric door locks to the S1/S2 terminals
of the door stations.
Main Monitor Station
Door Station 1
Door Station 2
Power Supply Unit
NP: Non-polarised
VL
VL- -SWD501EX wiring schematic diagram SWD501EX wiring schematic diagram

*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
●A certified power supply wiring has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered.
A certified power supply wiring not lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When using an electric lock or a connection device for option output (A contact), select a device
that meets the following guidelines:
●Electric lock connection terminal (S1/S2, S3/S4):
--N/O dry closure contact
-- 12 V AC/DC, less than 1 A
●Connection device for option output (A contact) terminal (OUT1/OUT2):
-- 24 V AC/DC, less than 0.3 A (minimum contact: 5 V DC 1 mA)
Wiring run Wire type*1
Diameter Length (Max.)
Main Monitor Station –
Door station A
φ0.65 mm 22 AWG 100 m
φ1.0 mm 18 AWG 130 m
φ0.5 mm CAT 5 50 m
Main Monitor Station –
Power Supply Unit Bφ0.65 mm 22 AWG 10 m
φ1.0 mm 18 AWG 20 m
Power Supply Unit –
AC power source Cφ1.2 mm - φ2.0 mm
(17 AWG - 12 AWG) No requirement
Door Station –
Electric Lock*2 Dφ0.5 mm - φ1.2 mm
(24 AWG - 17 AWG) According to specification of connected device.
Main Monitor Station -
Connection device for option
output (A contact)*2 Eφ0.5 mm - φ1.2 mm
(24 AWG - 17 AWG) According to specification of connected device.
VL
VL- -SWD501EX wiring type and length SWD501EX wiring type and length

Door Station Installation
Door Station Installation

Screws x 2 *
Mounting base
Wire
83.5
mm
Wall
Installing the door station
(VL-V554EX)
Attach the mounting base to the wall
securely.
Use a hex wrench to loosen screw A and
remove the front panel of the door station.
Front panel
Screw A
2 mm hex wrench
Connect the wires
<Rear view>Terminals for the
electric locks
Terminal for the
main monitor station
1Loosen the screws.
2Push in the wires to the terminal connectors
(non-polar), then tighten the screws.
•Install the mounting base on a vertical flat wall.
Step 1 Step 2
Step 3
(locally procured)
Door Station
Door Station Installation Installation

Installing the door station
(VL-V554EX)
Attach the door station to the mounting base.
Screws x 4
Name plate Screw A
•Write the name on the name plate as needed.
Attach the name plate to the door station and
use screw A to secure the front panel.
Important
• On the bottom surface of the door station and the
mounting base, there are holes to allow water to drain. Do
not cover them up when installing.
• When existing wiring (such as chime wires) is used:
- It may contain AC voltage that may cause electric shock
and/or damage the product.
-
Never use the following types of wiring. Consult a qualified
technician/dealer.
Step 4
Step 5
Door Station
Door Station Installation Installation

Installing the door station
(VL-V554UEX)
Install the flush mounting box in the wall. Use a hex wrench to loosen screw A and
remove the front panel of the door station.
Front panel
Screw A
2 mm hex wrench
Connect the wires
<Rear view>
Terminal for the
electric lock
Terminal for the
main monitor station
1Loosen the screws.
2Push in the wires to the terminal connectors
(non-polar), then tighten the screws.
151mm
Flush mounting box
Knockout hole*1
100mm
37mm
*1 Only open the knockout holes as required for
the wiring.
Step 1 Step 2
Step 3
Door Station
Door Station Installation Installation

Installing the door station
(VL-V554UEX)
Attach the door station to the flush
mounting box.
Screws x 4
Name plate Screw A
•Write the name on the name plate as needed.
Attach the name plate to the door station
and use screw A to secure the front panel.
Important
• On the bottom surface of the door station and the
mounting base, there are holes to allow water to drain. Do
not cover them up when installing.
• When existing wiring (such as chime wires) is used:
- It may contain AC voltage that may cause electric shock
and/or damage the product.
- Never use the following types of wiring. Consult a qualified
technician/dealer.
Step 4
Step 5
Door Station
Door Station Installation Installation

(Units: mm) Image range
Approx. 95°
Approx. 1,450
Approx. 900
Approx. 1,100
Approx. 2,000
View when looking
from above
Approx. 170°
Approx. 500
Approx. 500
Door station installation position
Installation height and area visible by the camera lens
You can use the [Wide/Zoom settings] setting on the main monitor station to select the area
that is visible when a visitor calls; available settings are [Wide], [Zoom], and [All] (entire
image display).
Centre of
door station Image displayed on
main monitor station
When set to wide (default)
Door Station
Door Station Installation Installation

Door station installation position
Displays a portion of the wide image at 2 times the size.
•Because a digital zoom is used, the image quality of zoom display is lower than that of wide
display or entire image display.
Zoom Image display
When set to zoom
Wide image display
Approx.
twice the zoom
vertically/
horizontally
Door Station
Door Station Installation Installation

Door station installation position
Installation Position - Zoom
You can use the main monitor station’s [Zoom position settings] setting to select the desired area visible when
zooming. Refer to Installation Position and configure the main monitor station.
Up and down
(Units: mm)
Left and right (when looking from above)
(Units: mm)
Approx.
45°
Image range
Approx. 2,050
Approx. 1,500
Approx.
500
Approx.
1,450
Centre of
door station
Approx.
45°Image range
Approx. 1,650
Approx. 1,250
Approx.
500
Approx.
1,450
Centre of
door station
Approx.550
Approx.400
Centre (default)
Up Down
Approx.
45°Image range
Approx.
1,400
Approx.
850
Approx.
500
Approx.
1,450
Centre of
door station
Approx.
550
Left
Approx.
85°
Approx. 500
Approx. 170°
Image range:
Approx. 900
Centre (default)
Image range:
Approx. 900
Approx.
500
Approx. 85°
Approx. 500
Approx. 170°Approx.
85°
Image range:
Approx. 900
Right
Door Station
Door Station Installation Installation

Door station installation position
(Units: mm) Image range
Approx. 115°
Approx. 1,450
Approx. 650
Approx. 1,600
Approx. 2,250
View when looking
from above
Approx. 170°
Approx. 500
Approx. 500
Centre of
door station Image displayed on
main monitor station
The area above and below the wide image is visible.
Entire image display
Door Station
Door Station Installation Installation

Main Monitor Station Installation
Main Monitor Station Installation

Mounting bracket
Vertical, flat wall
Hole in wall
83.5 mm
60 mm
7 mm
50 mm
Screws
Installing the main monitor station
Attach the mounting bracket to the wall securely.
・Install the mounting bracket on a vertical flat wall.
Step 1
(locally procured)
Main
Main Monitor Station Installation Monitor Station Installation

How to make wiring connections:
While pressing on the button with a
pointed object such as a screwdriver,
insert the wire into the terminal
connector. (To disconnect a wire,
while pressing on the button, pull out
the wire.)
How to connect the DC cable:
1Remove screw A and then remove the terminal cover.
2Loosen screw B and push in the wires of the DC cable
to the terminal connectors (non-polar), then tighten the
screws.
3Use the cable binder to secure the DC cable (double-
coated area) to the main monitor station.
4Make sure to replace the terminal cover.
Mount the main monitor station to the mounting
bracket.
Connect the DC cable and wires.
Bare wire at tip
12 mm
32 mm
Cable binder
Screw B
Screws A
Bare wire at tip Terminal Button
9 mm
Installing the main monitor station
Wiring from
door station
9 mm
Step 2
Step 3
1Line up the tab on the bottom of the bracket with the
groove on the main monitor station (1).
2Line up the tab on the top of the bracket with the groove
on the main monitor station, and push the main
monitor station down until it is secure (2).
(2)
(1)
Main
Main Monitor Station Installation Monitor Station Installation

Main monitor station installation position
About the installation position of the main monitor station and mounting bracket
• Place the main monitor station in a location that your eyes are the same height as the centre of the display.
• For the following reasons, leave at least 20 cm of space above, below, and to the left and right sides of the
main monitor station:
To prevent malfunction and sound cutting out
To ensure SD cards can be inserted and removed, and to make sure the reset button can be used (the SD
card slot is on the side of the main monitor station; the reset button is on the bottom.)
• After deciding where to install the main monitor station, attach
the mounting bracket in the location shown on
the right.
20 cm
SD card slot
20 cm
20 cm
20 cm
Reset button
82.7 mm
82.5 mm
Main monitor station
installation position
Main
Main Monitor Station Installation Monitor Station Installation

Power Supply Unit Installation
Power Supply Unit Installation