Panasonic PN54021K User manual

Product Outline
1000BASE-SX SFP Module and 1000BASE-LX SFP Module are SFP (Small Form-Factor
Pluggable) modules to be connected to a Panasonic Switching Hub’s SFP extension slot.
1000BASE-SX SFP Module 1000BASE-LX SFP Module
PN54021K PN54023K
IEEE802.3z
1000BASE-SX
IEEE802.3z
1000BASE-LX
SFF-8472 (Diagnostic Monitoring Interface)
850 nm 1310 nm
DC 3.3 V
0 to 50°C /20 to 80% RH (No dew condensation)
Specifications
Product name
Standards
Compatible cable
Optical wavelength
Operating voltage
Power consumption
Operating ambient
temperature/humidity
Fiber optic port
connector type
Accessories
MMF cable
LC connector (Duplex)
SMF, MMF cable
0.7 W max 0.9 W max
External dimensions
Mass (Weight) 17 g
9 mm (Height) x 14 mm (Width) x 57 mm (Depth)
(Excluding protruding sections)
Installation Guide (this document) x 1
Protection cap of the fiber optic port (Attached to the module) x 1
Module No.
MMF: Multi Mode Fiber SMF: Single Mode Fiber
1. Securely connect the SFP Module to the SFP
extension slot of a Panasonic Switching Hub.
2. Remove the protective cap of the SFP
Module’s fiber optic port.
3. Connect a fiber optic cable that meets the
standards specified for the SFP Module.
4. Connect another SFP Module of the same
model number on the opposite end.
Installation
SFP extension slot
SFP Module
Fiber optic port Switching Hub
1. Unlatch the fiber optic cable and remove it from the SFP
Module.
2. Pull down the lever of the SFP Module 90 degrees as
shown in the figure to unlatch the SFP Module.
3. Pull out the SFP Module.
Removal
Lever C0913-10719 Printed in Japan
 Thank you for purchasing our product.
 This document provides important information about safe and proper
operations of this SFP Module.
 Please read the "Important Safety Instructions".
 Any problems or damage resulting from disassembly of this SFP
Module by customers are not covered by the warranty.
PN54021K/PN54023KModel No.
1000BASE-LX SFP Module (SFP-1000LX)
1000BASE-SX SFP Module (SFP-1000SX)
Installation Guide
2-12-7, Higashi-Shimbashi, Minato-ku, Tokyo Japan, 105-0021
©2019

This chapter contains important safety instructions for preventing bodily injury
and/or property damage. You are required to follow them.
Do not look at the laser light.
Deviation could lead to visual impairment. (Class 1 Laser Product)
Do not disassemble and/or modify this SFP Module.
Deviation could lead to fire, electric shock, and/or equipment failure.
 Severity of bodily injury and/or property damage, which could result from incorrect
use of the SFP Module, are explained below.
 The following symbols are used to classify and describe the type of instructions to be
observed.
Important Safety Instructions
This symbol indicates safety instructions.
Deviation from these instructions could lead to
bodily injury and/or property damage.
CAUTION
This symbol indicates a potential hazard
that could result in serious injury or death.
WARNING
This symbol is used to alert
users to what they must do.
This symbol is used to alert
users to what they must not do.
WARNING
CAUTION
Handle the SFP Module carefully so that fingers or hands may not be
injured by its end connected to the Switching Hub or the SFP extension
slot of the Switching Hub.
Basic Instructions for the Use of This Product
For inspection and/or repair, consult the retailer.
Correctly and securely connect the SFP Module to the SFP extension slot of
a Panasonic Switching Hub.
Check the connector of the fiber optic cable for dirt and dust. If it is dirty,
be sure to clean it before connecting it to the fiber optic port.
Remove the SFP Module from the SFP extension slot before cleaning the
SFP Module.
Do not touch the metal terminal or place electrically-charged objects in the
proximity of the SFP Module. Static electricity could lead to breakdown.
Please use the SFP Module in locations where the ambient temperature is
within the range of 0 to 50°C.
Do not use the SFP Module in any condition where the specification limits
are exceeded.
Deviation could lead to malfunctions.
1. Panasonic will not be liable for any damage resulting from the operation not in
accordance with this document or the loss of communications, which may or
may not be caused by failure and/or malfunction of this product.
2. The contents described in this document may be changed without prior notice.
3. For any question, please contact the shop where you purchased the product.
 The port LED of the Switching Hub to which the SFP Module connected is not lit.
Is the Switching Hub powered on?
Is the SFP Module securely connected to the target SFP extension slot of the
Switching Hub?
Is the connected port of the Switching Hub enabled?
Is the cable correctly connected to the target port?
Is a conforming cable used? Is the same type of SFP Module used on the
opposite end?
Is the equipment connected to the target port compliant with the specified
standards?
Ensure that 100BASE-FX or 10GBASE equipment is not connected.
Troubleshooting
If you find any problem, please take the following steps to check.