Panasonic KX-TDA30 User manual

Model No. KX-TDA30
Thank you for purchasing a Panasonic Hybrid IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDA30: PSMPR Software File Version 5.0000 or later
Hybrid IP-PBX
Getting Started

Table of Contents
1 Before Installation ....................................................................................3
1.1 Safety Notices ...................................................................................................................4
1.2 System Connection Diagram ...........................................................................................5
1.3 Unpacking ..........................................................................................................................6
2 Installation ................................................................................................9
2.1 Opening/Closing the Covers ..........................................................................................10
2.2 Installing the SD Memory Card ......................................................................................11
2.3 Installing the Optional Service Cards ...........................................................................12
2.4 Installing the Trunk Cards ..............................................................................................15
2.5 Installing the Extension Cards (DLC4/DLC8/SLC4/SLC8) ...........................................16
2.6 Connecting Extensions ..................................................................................................17
2.7 Frame Earth Connection ................................................................................................17
3 Starting the PBX .....................................................................................19
3.1 Starting the PBX ..............................................................................................................20
4 Customising the PBX .............................................................................23
4.1 Connecting the PC ..........................................................................................................24
4.2 Installing the Maintenance Console ..............................................................................25
4.3 Programming the PBX ....................................................................................................25
5 Confirming the Connection ...................................................................31
5.1 Making Calls ....................................................................................................................32
2 Getting Started
Table of Contents

Section 1
Before Installation
Getting Started 3

1.1 Safety Notices
Please observe the safety notices in this manual in order to avoid danger to users or other people, and prevent
damage to property.
The notices are classified as follows, according to the severity of injury or damage:
WARNING This notice means that misuse could result in death or serious injury.
CAUTION This notice means that misuse could result in injury or damage to property.
4 Getting Started
1.1 Safety Notices

1.2 System Connection Diagram
Amplifier Pager/Speaker
SLT Wireless
Phone
AC Cord & AC Adaptor
*1
Station Message
Detail Recording (SMDR)
PC
ECHO8
(KX-TDA3166)
EXT-CID
(KX-TDA3168)
MSG2
(KX-TDA3191)
IP-GW4
(KX-TDA3480)
APT
DPT DSS
Console
Voice
Processing
System
Radio
CTI Server
4 Super Hybrid Ports
*2
PT-interface CS PS
Batteries
Main Board
SLT Fax Machine
for Single Line Device
for Single Line Device,
DPT/Analogue
Proprietary Telephone
(APT), DSS Console,
and PS
MEC
(KX-TDA3105)
LCOT2
(KX-TDA3183)
CID4
(KX-TDA3193)
LCOT4
(KX-TDA3180)
DID3
(KX-TDA3182)
ISDN BRI Line
ISDN BRI Line
(Digital Trunk)
(Digital Trunk)
ISDN BRI Line
(Digital Trunk)
Analogue
Trunk
BRI2
(KX-TDA3280)
BRI1
(KX-TDA3283)
Doorphone & Door Opener
External Sensor/
External Relay Device
PC
RMT
(KX-TDA3196)
SVM2
(KX-TDA3192)
ESVM2
(KX-TDA3194)
E1 Line
E1 Line
(Digital Trunk)
(Digital Trunk)
E1 Line
(Digital Trunk) E1
(KX-TDA3188)
Telephone
Company
PC
LAN
CTI Server
LAN
IP-PT IP Softphone
ITSP*3
Network
WAN
SIP-DSP4
(KX-TDA3451)
SIP-GW4
(KX-TDA3450)
PC
LAN
KX-DT300/
KX-T7600
DPT
KX-DT300/
KX-T7600
DPT
PC DSS
Console
DPT
Voice
Processing
SystemPT-interface CS PS
for Digital Proprietary
Telephone (DPT),
DSS Console, and
Portable Station (PS)
KX-DT300/
KX-T7600
DPT
KX-DT300/
KX-T7600
DPT
KX-DT346/
KX-DT343/
KX-T7636/
KX-T7633 DPT
KX-DT346/
KX-DT343/
KX-T7636/
KX-T7633 DPT
DCE*4
(e.g., ADSL
Modem)
DLC8
(KX-TDA3172)
DLC4
(KX-TDA3171)
IP-EXT4
(KX-TDA3470)
SLC8
(KX-TDA3174)
SLC4
(KX-TDA3173)
DPH4
(KX-TDA3161)
DPH2
(KX-TDA3162)
Private
IP Network
Router
*1 In addition to the supplied AC adaptor, an additional AC adaptor can be connected to the PBX.
*2 The PBX has 4 Super Hybrid Ports pre-installed.
*3 ITSP: Internet Telephony Service Provider
*4 DCE: Data Circuit Terminating Equipment
Getting Started 5
1.2 System Connection Diagram

Note
In this manual, the suffix of each model number (e.g., KX-TDA30NE) is omitted unless necessary.
1.3 Unpacking
Check the package contents.
Main Unit ´ 1
CD-ROM (including manuals, etc.) ´ 1
AC Cord*1 ´ 1 AC Adaptor ´ 1 Screw ´ 5
Washer ´ 5 Mini Plug (for pager and music
source) ´ 2
SD Memory Card ´ 1
Main Strap ´ 1 Optional Card Label Sheet ´ 1
*1 The type of the AC cord may vary depending on the country/area of use.
KX-TDA30BX is supplied with 2 types of AC cord. Please use whichever is appropriate for the country/area.
6 Getting Started
1.3 Unpacking

Necessary tools (not supplied):
ü Telephone cable for extension connection:
Diameter of cable
(ø 0.4 mm to ø 0.6 mm)
Maximum length of cable
ø 0.5 mm 1128 m for SLT
ø 0.5 mm 720 m for KX-DT300/KX-T7600 series
ø 0.5 mm 229 m for other DPT, APT and DSS Console
The maximum length of the cable may vary depending on the type of the cables and installation conditions.
ü An RS-232C or USB cable for PC connection
ü Connectors (RJ45/RJ11)*1 for trunk and extension connections
*1 The connector type may be RJ45 or RJ11 depending on the country/area.
Note
Use a twisted pair cable for the RJ45 or RJ11 connector.
Getting Started 7
1.3 Unpacking

8 Getting Started
1.3 Unpacking

Section 2
Installation
Getting Started 9

2.1 Opening/Closing the Covers
Opening the Covers
1. Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable cover
slightly to remove it.
Slide Button
Cable Cover
2. Remove the three screws.
Screw
3. Holding the protrusions on both sides of the front cover, swing the cover open.
10 Getting Started
2.1 Opening/Closing the Covers

Closing the Covers
1. Close the front cover, then tighten the three screws.
Screw
2. Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the
front hooks fit in place.
Cable Cover
3. Slide the cable cover down until it locks.
2.2 Installing the SD Memory Card
The SD Memory Card contains software for all the processes of the PBX and all the customer data.
Getting Started 11
2.2 Installing the SD Memory Card

The SD Memory Card must be inserted before startup.
SD Memory Card
Slot Cover
SD Memory
Card
CAUTION
Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX to
fail to start when you try to restart the system.
2.3 Installing the Optional Service Cards
Slot Position
02
03
04
05
06
07
08
09
10*1
11*1
01*2
*1 Slots 10 and 11 accept only cards which do not have external ports. Therefore, these slots do not have removable cover plates.
*2 Slot 01 contains the pre-installed Super Hybrid Ports. No optional service card can be installed.
Slot Restrictions
The following table shows the slot restrictions. "ü" indicates that the slot supports the optional service card.
Card Slot Number
Type Max 02 03 04 05 06 07 08 09 10 11
LCOT4 3 ü ü ü
LCOT2 3 ü ü ü
12 Getting Started
2.3 Installing the Optional Service Cards

Card Slot Number
Type Max 02 03 04 05 06 07 08 09 10 11
DID3 2 ü ü ü
BRI2 3 ü ü ü
BRI1 3 ü ü ü
DLC4
1*1
ü ü ü
SLC4 ü ü ü
E1 1 ü ü ü
SIP-GW4 1
2
ü ü ü
IP-GW4 1 ü ü ü
IP-EXT4 1 ü ü ü
DLC8
2*2
ü ü ü
SLC8 ü ü ü
DPH4
1*3
ü ü
DPH2 ü ü
ECHO8 1 ü ü ü ü
EXT-CID 1 ü ü ü ü
MSG2 2
4
ü ü ü ü
SVM2 2ü ü ü ü
ESVM2 4ü ü ü ü
*1 Only one of either the DLC4 or SLC4 card can be installed.
*2 A maximum of two DLC8 cards, two SLC8 cards, or one of each card can be installed.
*3 Only one of either the DPH4 or DPH2 card can be installed.
CAUTION
To protect the main board from static electricity, do not touch parts on the main board or on the optional
service cards. To discharge static electricity, touch ground or wear an earthing strap.
Getting Started 13
2.3 Installing the Optional Service Cards

Installing the Trunk/Extension Cards
1. Before installing the optional service cards, cut and remove the appropriate dummy cover plates from the
main unit.
Dummy Cover Plate
CAUTION
For safety reasons, smooth the cut edges after removing the dummy cover plates.
2. Position the card in the open slot, making sure that the tabs on the both sides of the card fit into place.
Then, holding the card firmly in place, lower the rear end so that the hole of the card fits over the extension
bolt.
1
2
Extension Bolt
Optional Service Card
CAUTION
When installing the optional service cards, do not put pressure on any parts of the main board. Doing
so may result in damage to the PBX.
14 Getting Started
2.3 Installing the Optional Service Cards

3. Insert the new extension bolt (included with the card) into the hole on the card, and tighten it to secure the
card.
Extension Bolt
2.4 Installing the Trunk Cards
LCOT2/LCOT4 Card
To trunk
RJ45
Example: LCOT4 Card
Accessories (included): Extension Bolt ´ 1, Strap ´ 1
User-supplied (not included): RJ45 connector (for LCOT2 card), or RJ45 connector or RJ11 connector (for
LCOT4 card)*1
*1 The connector type may be RJ45 or RJ11 depending on the country/area.
Getting Started 15
2.4 Installing the Trunk Cards

BRI1/BRI2 Card
To NT1
RJ45 (LINE 1)
RJ45 (LINE 2)
Example: BRI2 Card
Accessories (included): Extension Bolt ´ 1, Strap ´ 1
User-supplied (not included): RJ45 connector
Note
•Connect these optional service cards to the trunk through an NT1; do not connect to the U interface of
the trunk directly.
•These optional service cards have 100 W of terminal resistance. For use in point to multi-point
connection, the card must be placed at the end of the bus.
2.5 Installing the Extension Cards (DLC4/DLC8/
SLC4/SLC8)
Example: DLC4 Card
To extension
RJ45
Accessories (included): Extension Bolt ´ 1, Strap ´ 1
User-supplied (not included): RJ45 connector or RJ11 connector*1
*1 The connector type may be RJ45 or RJ11 depending on the country/area.
16 Getting Started
2.5 Installing the Extension Cards (DLC4/DLC8/SLC4/SLC8)

2.6 Connecting Extensions
Example: KX-T7600 Series DPT Pin Assignments
To extension card
RJ11
TO MAIN UNIT
/ PABX
DPT and DSS Console
KX-T7000 Series SLT
H L
T R
APT
HTRL
H L
2.7 Frame Earth Connection
1. Loosen the screw.
2. Insert an earthing wire (user-supplied).
3. Tighten the screw.
4. Connect the earthing wire to earth.
Screw
Earthing
wire
To earth
WARNING
•Connect the frame of the PBX to earth.
•Proper earthing (connection to earth) is very important to protect the PBX from the bad effects
of external noise or to reduce the risk to the user of electrocution in the case of a lightning
strike.
CAUTION
•For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor
must be more than 0.75 mm2 or 18 AWG.
•The earthing wire of the AC cable has an effect against external noise and lightning strikes, but it may
not be enough to protect the PBX. A permanent connection between earth and the earth terminal of
the PBX must be made.
Getting Started 17
2.7 Frame Earth Connection

18 Getting Started
2.7 Frame Earth Connection

Section 3
Starting the PBX
Getting Started 19

3.1 Starting the PBX
CAUTION
•Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing
an earthing strap.
•Once you have started the PBX and if you unplug the PBX, do not perform the following procedures
to start the PBX again. Otherwise, your programmed data will be cleared.
•The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located
near the equipment and is easily accessible.
Notice
The SD Memory Card must be inserted in the SD Memory Card slot of the main board before startup.
Note
The PBX will continue to be powered even if the power switch is turned "OFF".
1. Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position.
System Initialise Switch
RUN Indicator
ALARM Indicator
2. Plug the DC connector of the AC adaptor into DC IN 1.
AC Adaptor
DC Connector
DC IN 1
2
1
20 Getting Started
3.1 Starting the PBX