Panasonic CZ-RWSU2 User manual

Save these instructions!
Conservez précieusement ces instructions !
Diese Anleitung aufbewahren!
Conservare le presenti istruzioni!
Guarde estas instruções!
Φυλάξτε αυτές τις οδηγιες!
¡Guarde estas instrucciones!
Сохраните эту инструкцию!
Збережіть ці інструкції!
CZ-RWSU2
CZ-RWST2
CZ-RWSL2
CZ-RWSC2
CZ-RWSY2
CZ-RWSK2
EN
ES
RU
UK
FR
DE
IT
GR
PT
Wireless Remote Control System INSTRUCTION MANUAL
Système de télécommande à infrarouge MANUEL D’UTILISATION
Drahtloses Fernbedienungssystem BEDIENUNGSANLEITUNG
Sistema Telecomando Senza Fili MANUALE DI ISTRUZIONI
Sistema de telecomando sem fios MANUAL DE INSTRUÇÕES
Ασύρματο σύστημα τηλεχειριστηριου ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ
Sistema de control remoto inalámbrico
MANUAL DE INSTRUCCIONES
Беспроводная система дистанционного управления ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
Бездротова система дистанційного керування ПОСІБНИК КОРИСТУВАЧА
85464609072022
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15
16
REMOTE CONTROL / TÉLÉCOMMANDE / FERNBEDIENUNG /
TELECOMANDO / TELECOMANDO / ΤΗΛΕΧΕΙΡΙΣΤΗΡΙΟ /
CONTROL REMOTO / ПУЛЬТ ДИСТАНЦИОННОГО УПРАВЛЕНИЯ /
ПУЛЬТ ДИСТАНЦІЙНОГО КЕРУВАННЯ
Printed in China
Authorized representative in EU
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
00Instructioncover9L.indd100Instructioncover9L.indd1 2012/09/1212:41:492012/09/1212:41:49

Receiver / Récepteur / Empfänger / Ricevitore / Receptor /
Δέκτης / Receptor / Приёмник / Приймач
Display / Affichage/
Anzeige / Display
Visor / Οθόνη
Visor / Дисплей / Дисплей
1
2
3
4
5
6
7
8
9
CZ-RWSC2
1543
2
CZ-RWST2 CZ-RWSL2
345
1
2
7
89
Operation Panel / Panneau de commande
Bedienfeld / Pannello di Comando
Painel de comando / Πλαίσιο λειτουργίας
Panel de operaciones / Панель управления /
Панель керування
I II
3
4
5
2
Indoor Unit (CZ-RWSK2) / Appareil intérieur (CZ-RWSK2) / Raumeinheit (CZ-RWSK2) /
Apparecchio Interno (CZ-RWSK2) / Unidade interior (CZ-RWSK2) / Εσωτερική μονάδα (CZ-RWSK2)/
Unidad interior (CZ-RWSK2) /
Внутренний блок
(CZ-RWSK2) /
Внутрішній блок
(CZ-RWSK2)
2
3
4
5
1
CZ-RWSY2
CZ-RWSU2





00Instructioncover9L.indd200Instructioncover9L.indd2 2012/09/1212:41:502012/09/1212:41:50

EN-1
EN
Contents
1. Important Safety Instructions ...............................................EN-2
2. Names and Operations ........................................................EN-3
3. Installing Batteries................................................................EN-5
4. Setting the Current Time ......................................................EN-6
5. Operation .............................................................................EN-7
6. Timer Operation ...................................................................EN-9
7. Adjusting the Wind Direction ..............................................EN-11
8. Operating Multiple In/Outdoor Units Simultaneously .........EN-12
9. Using the Remote Control..................................................EN-13
10. For Best Results.................................................................EN-13
11. Addresses ..........................................................................EN-14
12. Emergency Operation ........................................................EN-17
13. Miscellaneous Settings ......................................................EN-19
14. Before Requesting Service ................................................EN-20
15. Specifications.....................................................................EN-21
Instructionhonbunall.indbEN-1Instructionhonbunall.indbEN-1 2012/09/1212:39:112012/09/1212:39:11

1. Important Safety Instructions
EN-2
Before using the system, be sure to read these
“Important Safety Instructions”.
After reading this manual, save it in a convenient
place.
Warning
Installation Precautions
• Do not install yourself
Installation should always be performed by your
dealer or a professional service provider.
Electric shock or fire may result if an
inexperienced person performs any installation
or wiring procedures incorrectly.
• Use only specified air conditioners
Always use only air conditions specified by the
dealer.
Precautions for Use
• Do not touch switches with wet hands
Electric shock and damage to the system can
result.
• Protect the remote controller from water Damage
to the system can result.
• Stop the system and turn the power off if you
sense unusual smells or other irregularities
Continuing operation when the system is out of
order can result in electric shock, fire, and
damage to the system. Contact your dealer.
• Do not swallow the battery.
Moving and Repair Precautions
• Do not repair
Never repair the system by yourself.
• Contact your dealer before moving the system
Contact your dealer or a professional service
provider about moving and reinstalling the system.
Electric shock or fire may result if an
inexperienced person performs any installation
procedures incorrectly.
Instructionhonbunall.indbEN-2Instructionhonbunall.indbEN-2 2012/09/1212:39:122012/09/1212:39:12

2. Names and Operations
EN-3
EN
1. Operation Display
Displays the operation status. (The figure
shows all the statuses.)
• The auto-flap display may be different,
depending on the installed unit. (See Page
EN-11)
2. Start/Stop button
Pressing this button once starts and pressing
again stops the operation.
3. Fan speed button
4. Swing/Wind Direction button
5. Timer setting button
Use for operating with a timer.
6. Reset button
Use this button after changing the batteries.
7. Cover
Press at the top center and then slide down.
8. Transmitter
9. Remote control sensor
Detects the temperature at the remote
controller when detection has been switched
to the remote control by the sensor button.
10. Temperature setting buttons
raises the temperature setting 1 °C at
a time.
lowers the temperature setting 1 °C at
a time.
11. Filter button
CZ-RWSC2
Press to turn off the filter lamp on the
receiver.
12. Mode Select button
Press to switch the operation mode.
13. Ventilation button
Use this when connected to an aftermarket
fan. Pressing this button starts and stops the
fan. When the air conditioner is started or
stopped, the fan starts or stops at the same
time. ( appears on the display of the
remote control when the fan is operating.)
14. Address button
15. Sensor button
Use this when switching to detect the
temperature at the remote control. At
shipping the default setting is set to detect
the temperature at the unit. At this time is
shown on the display.
16. Clock button
Use this when setting the clock.
REMOTE CONTROL One remote control can control a group of up to eight indoor units.
(See Page EN-12)
From this page on the names of remote control
buttons will be abbreviated as the illustration of
the “button”.
E.g.: Start/Stop button Æ
Instructionhonbunall.indbEN-3Instructionhonbunall.indbEN-3 2012/09/1212:39:122012/09/1212:39:12

EN-4
1. Receiver
Receives the signal sent from the remote
control.
2. Emergency operation button
Display lamps
When an error occurs, one of the lamps flashes. When a
display lamp is blinking, refer to “14. Before Requesting
Service”.
3. Operating lamp
This lamp is lit when the unit is operating.
4. Timer lamp
This lamp is lit when the timer is set.
5. Standby lamp
• When the heater is working, the lamp lights
at the following times. When the thermostat
has operated during defrosting at the time
of the startup.
• The lamp flashes when an error occurs.
6. Filter lamp
This lamp is for notifying you when the filter
needs to be cleaned.
7. Swing button
8. Normal/Stop All switch
Use in the Normal position. It does not
operate in the Stop All position.
Remote control, main / remote control,
secondary, switch
In normal use this should be on remote
control, main. It is also possible to use both
in conjunction with a wired remote control
(sold separately). (Consult with the dealer
where the product was purchased about
making the settings.)
Test/On switch
This is used during service. It is not for
normal use.
Test Run/On switch
This is used during service. It is not for
normal use.
9. Address switch
Differentiate between incoming and outgoing
signals.
Note
• If a heat pump model is being used, it will beep
twice and the operating lamp will light up on the
display; if the timer and standby lamps blink
alternately, a conflict between the heating and
cooling exists, so the unit cannot operate in the
desired mode. (On models that do not have an
Auto function, even if Auto is selected, it works in
the same way.)
• When the local operation is disabled by such as
the centralized control, and if the Start, Stop, Mode
or Temperature setting buttons are pressed, the
unit will beep five times and the change will not be
made.
Receiver
2. Names and Operations (Cont.)
Instructionhonbunall.indbEN-4Instructionhonbunall.indbEN-4 2012/09/1212:39:122012/09/1212:39:12

3. Installing Batteries
EN-5
EN
1. Remove the cover.
2. Insert two AAA alkaline batteries.
Put the batteries in with the polarity [+/–] as shown in the
figure.
3. Gently insert one end of an unfolded paper clip
(or a similar object that can fit) into the Reset hole
and press the reset button inside the hole and
then put the cover back on.
Note
• Change the batteries when the display of the remote control
gets weak or if it will not work unless close to the receiver.
(Alkaline batteries generally last about one year.)
• When changing batteries, always use two fresh batteries of the
same make.
• If the remote control will not be used for a long period of time,
remove the batteries.
• Please dispose of batteries appropriately.
• After changing the batteries, follow the procedures on the next
page to reset the current time.
HOW TO REMOVE BATTERIES
1. Remove the cover.
2. Press the battery toward the negative end and
lift it out by its positive end. (As shown at right)
3. Remove the other battery in the same way.
Note
• Dispose of the used batteries at the designated location in
compliance with the applicable local ordinances.
Warning
• Do not swallow the battery.
• After removing the battery from remote control unit, keep it away from the reach of children.
The battery can cause death by suffocation if swallowed.
• When inserting the battery, make sure the polarities (+ and -) are correct.
Reset hole
Cover
Instructionhonbunall.indbEN-5Instructionhonbunall.indbEN-5 2012/09/1212:39:122012/09/1212:39:12

4. Setting the Current Time
EN-6
After changing the batteries and pressing reset, be sure to reset the
current time.
(When reset is pressed, the current time reverts to [ ])
1. Press for two seconds or more.
Once the clock displays starts blinking, the clock can be set.
2. Set the hour with / of the .
If you press and hold the button, the time changes quickly.
3. Set the minutes with / of the .
If you press and hold the button, the time changes quickly.
4. Pressing completes the time setting.
• While you are setting the current time, the time display flashes but
the colon does not.
• If the buttons are not pressed for three minutes while setting the
current time, it is set to the displayed time.
Note
• When reset is pressed, the timer settings are deleted.
21, 4
3
Instructionhonbunall.indbEN-6Instructionhonbunall.indbEN-6 2012/09/1212:39:122012/09/1212:39:12

5. Operation
EN-7
EN
Power:Turn on the power of the indoor unit at least 14 hours
before operation.
1. Press .
2. Press and select from among Auto ,Heat ,Dry ,
Cool and Fan .
3. Press and select the desired speed.
If set to Auto , the fan speed switches automatically. (Auto does
not work when in the Fan mode.)
4. Press one of the buttons and set the desired
temperature.
Temperature settings cannot be made when in the Fan mode.
MAX MIN
Auto 27 17
Heat 26 16
Dry / Cool 30 18
Stop: Press .
When the unit is stopped with the remote control, even though the
compressor of the outdoor unit stops, the fan on the outdoor unit
may continue to run for a while.
Auto , Heat , Dry , Cool , Fan
Models that only provide the cooling function cannot operate in the auto or heating modes.
1
4
2
3
Instructionhonbunall.indbEN-7Instructionhonbunall.indbEN-7 2012/09/1212:39:132012/09/1212:39:13

EN-8
If the unit is not heating very effectively with a Low fan speed , switch the fan
speed to High or Medium.
Depending on the indoor unit being used, it may indicate a function that it does not have. (The fan
speed is set.)
If you cannot turn the air conditioner off in the normal way.
Disconnect the power to the indoor unit and contact the dealer where the product was purchased.
<Auto Operation>
If all the indoor units are identical in a cooling system and are under control as one group, it heats or
cools automatically via the differences between the set temperature and the room temperature.
<Dry Operation>
• Depending on the indoor unit used, the remote control may have a [Dry] indicator on its display
even though the unit does not have the Dry function. (Same as cooler operation)
• When the room temperature approaches the temperature setting, the unit continues to start up or
stop automatically.
• When the drying mode stops operating, the indoor unit’s fan blows a gentle breeze in order to keep
the moisture from returning to the room at a minimum.
• Depending on the indoor unit used, and/or the temperature in the room, the fan speed may not be
adjustable.
• Depending on the unit used, when the outside air temperature is 15 °C or less, the dry function will
not operate.
5. Operation (Cont.)
Instructionhonbunall.indbEN-8Instructionhonbunall.indbEN-8 2012/09/1212:39:132012/09/1212:39:13