Panasonic KV-S2065L User manual

ORDERNO. KM70104623C0
G14
High SpeedScanner
KV-S2065L / KV-S2065W
1. GENERALPRECAUTIONS
1.1. SafetyPrecautions
1. Beforeservicing, unplug thepowercordtopreventelectrical
shock hazard.
2. Whenreplacing parts, useronlymanufacture’srecommended
components forsafety.
3. Check thecondition ofpowercord. Replace ifwearordamageis
evident.
4. Afterservicing, besuretorestoretheleaddress, insulation
1

barriers, insulation papers, shields, etc.
5. Beforereturning theservicedequipmenttothecustomer, perform
thefollowing electrical tests topreventshock hazard.
1.2. Electrical Tests
1. Unplug thepowercordand check forcontinuitybetweentheearth
ground connection on theplug and theInterface BoardCover.
Thereshouldbezeroohmresistance
2. Withtheunitunplugged, shorttheAClive-neutral oftheplug with
ajumperwire.
3. TurnONthepowerswitch.
4. Measuretheresistance valuewithanohmmeterbetweenthe
jumperedACplug and anexposedmetal cabinet part, suchas
screwheads, etc. (RefertoFig.2)
Note:
Someexposedparts maybeisolatedfromthechassisbydesign.
Theyreadinfinity.
5. Ifthemeasurementisless than1M , apossibilityforelectric
shock mayexit.
Note:
Thishazardouscondition must becorrectedbeforetheunitis
returnedtotheend user.
1.3. ForService Technicians
ICsand LSIsarevulnerabletostaticelectricity. Whenrepairing, thefollowing precautionswill
helptopreventrecurring malfunctions.
1. Covertheplasticparts withaluminumfoil.
2. Ground thesoldering irons.
2

3. Use aconductivemat on theworktable.
4. DonotgraspICorLSI pinswithbarefingers.
2. SPECIFICATION
Item Model No.
KV-S2065L KV-
S2065W
Scanner Scanning face Duplex scanning
Scanning method Frontside:CIS (ContactTypeImageSensor)
Back side:CIS (ContactTypeImageSensor)
Scanning speed Simplex scanning:Approx. 60 ppm (Letter, fedlengthwise,
200
Duplex scanning:Approx. 110 ipm (Letter, fedlengthwise,
200
Resolution Mainscanning direction:100-600 dpi (1dpi step)
Sub-scanning direction:100-600 dpi (1dpi step)(Sameas
main
scanning direction)
Optical resolution is400 dpi.
Tonal gradation Binarymode, Grayscalemode(4/8bit), 64-stepgradation (
dither)
mode, 64-stepgradation (error diffusion)mode
Imagecontrol Imageemphasis, Dynamicthreshold(DIMM required),
Automatic
threshold, Automaticseparation, Monochromereversing,
Automatic
back control
Compression MH, MR, MMR
Paper Size Scanning size:48 x70mm (1.9x2.75
in.)to216 x431mm (8.5x17 in.)
Feeding size:48 x70mm (1.9x2.75
in.)to305 x838mm (12 x33 in.)
Scanning size:48 x
70mm
x2.75 in.)to298 x
431mm
x17 in.)
Feeding size:48 x
70mm
2.75 in.)to305 x
838mm
33 in.)
Thickness Singlepaperfeeding:0.025 to0.2mm (1.0to7.9mils)
Continuouspaperfeeding:0.06 to0.2mm (2.4to7.9mils)
Note:1mil=1/1000 in.
Weight Singlepaperfeeding:20 to157g/m2(5.3to42 lbs.)
Continuouspaperfeeding:50 to157g/m2(13 to42 lbs.)
Interface (Transferrate) SCSI3(20MB/sec), 50pin
Unit External dimensions
(WidthxDepthxHeight) 495 x575 x246mm (19.5x22.6x9.7in.)
Mass (Weight) 19kg(41.8lbs.)
Powerrequirement AC100-120V, 50/60Hz
AC220-240V, 50/60Hz
Power
consumptionMaximum (Scanning)1.3A(AC100-120V)/98W
0.8A(AC220-240V)/98W
Minimum
(Standby) 0.5A(AC100-120V)/30W
0.3A(AC220-240V)/30W
Sleep
mode 0.13A(AC100-120V)/11W
0.07A(AC220-240V)/11W
3

Item Model No.
KV-S2065L KV-
S2065W
Operating
Environment Operating temperature and humidity 15°Cto30°C(59°Fto86°F), 30%to80%RH
Storage
Environment Storagetemperature and humidity 0°Cto35°C(32°Fto95°F), 10%to80%RH
Option Rollerexchangekit(KV-SS009), Imprinteroption (KV-SS010), Rollercleaning paper(
KV
Inkcartridge(KV-SS06), Whiterollerkitfor KV-S2065W(KV-SS048), Whiterollerkit
for
S2065L(KV-SS071)
“Weightinpounds”representstheweightof500 [17x22 inches (432x559mm)] sheets.
3. COMPONENTIDENTIFICATION
4

4. INSTALLATION
4.1. MinimumSpace Requirements
Besuretomaintaintherecommendedspace requirementsfor properventilation.
4.2. Removing and Keeping Screw and Fixture
4.3. DIMM ModuleExtension
Amaximum of256 MBextendedmemorymay berequireddepending on thecombination ofthe
papersize, resolution and gray scalemode.
Todeterminehowmuchextendedmemoryisrequired, refertothefollowing page“Additional
MemorySizeeachscanning mode(MB)”.
*RecommendedDIMM
-JEDEC-standard168pin, dual in-linememorymodule(DIMM)
5

-Non buffered
-Single+3.3V±0.3Vpowersupply
-Frequency/ CASLatency:100MHz/CL=2, 133MHz/CL=2, 133MHz/CL
=3
-64MB, 128MBor256MBmaybeused.
(Reference)DIMM modulewhichhas beenevaluatedusing thisscanner
-Manufacturer:DELKINDEVICES
1. Model No.:DM168-064Y3Q488-10S2P(64MB)
2. Model No.:DM168-064Y3Q446-10S2P(64MB)
3. Model No.:DM168-128Y3Q488-10S4P(128MB)
Note:
Originally, SCSI boardhas 16MBmemoryexceptfortheabove
additional memory.
4.4. Removing SCSI Board
1)Make surethePowerisOFF.
2)Remove SCSIBoard. (See 8.3.15)
Additional MemorySizeeachscanning mode(MB)
Simplex/4bit, 8bit
Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 64 64 64 128
A4 0 0 0 0 64 64
A5 0 0 0 0 0 64
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 64 64 64
B5(JIS) 0 0 0 0 64 64
B6(JIS) 0 0 0 0 0 0
DoubleLetter 0 0 64 64 64 128
Legal 0 0 0 64 64 64
Letter 0 0 0 0 64 64
Duplex/4bit, 8bit
6

Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 64 64 128 256
A4 0 0 64 64 64 128
A5 0 0 0 0 64 64
A6 0 0 0 0 0 64
B4(JIS) 0 0 64 64 128 128
B5(JIS) 0 0 0 64 64 64
B6(JIS) 0 0 0 0 64 64
DoubleLetter 0 0 64 64 128 256
Legal 0 0 64 64 64 128
Letter 0 0 64 64 64 128
Simplex/Binary
Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 0 0
A4 0 0 0 0 0 0
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 0 0
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
DoubleLetter 0 0 0 0 0 0
Legal 0 0 0 0 0 0
Letter 0 0 0 0 0 0
Duplex/Binary
Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 0 64
A4 0 0 0 0 0 0
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 0 0
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
DoubleLetter 0 0 0 0 0 64
Legal 0 0 0 0 0 0
Letter 0 0 0 0 0 0
4.5. Installing DIMM Module
7

InserttheDIMM moduleintotheconnector on the
SCSIinterface board atanangle[Place (1)]. Push
inthemoduleas faras itgoes. Theleversshould
lock automatically. Ifnot, pushtheleverstolock the
modulein[Place (2)].
Note:
-BesurethattheDIMM modulewill beintheproper
position and theproperside.
-Toremove theDIMM module, release thewhite
leversatbothsides oftheconnector.
4.6. Installing theSCSI Board
1)InserttheSCSIBoard intotheunitalong therails
and pushitinfirmly.
Confirm thattheSCSIboard plateisfullyinserted
until itfirmlylocks inplace.
8

2)SecuretheSCSIBoard withthe2screws.
3)Install thescannerdriversoftwareinyour
computeraccording totheenclosedmanuals.
4.7. Connecting theUnittoaPersonal Computer
Note:
*ACcordshownon thefigureisforAC100-120V.
Caution :
Setthepowerswitchon thescannerand on thepersonal computertoOFF beforeconnecting the
interface cable.
Use onlythepowercord thatissuppliedbythemanufacturer.
4.8. SystemConditionsRequirements
Whenusing thescanner, therequiredpersonal computerconditionsareas follows.
CPU Pentium 166MHzor higher(Pentium, Celeron processor or higheris
recommended.
Memory 64 MBor higher(128 MBor higherisrecommended.)
OS Windows95/Windows98/WindowsNT/Windows2000/WindowsMe
SCSIboard Adaptec Brand AHA-1540/2930/2940/19160/29160 Series are
recommended.
*Thescanning speeddiffersdepending on thepersonal computeroperating environmentor
9

application.
4.9. LCD Settings
Beforescanning thedocument, perform therequiredsettingson thedisplay. Setting information
and scannerconditionsareshownon thedisplay.
4.9.1. Setting thelanguage
1. Turnthepoweron whilepressing theHOMEkey.
Note:
Thelanguagesetting modeisselectedautomaticallywhenthe
unit’spoweristurnedon forthefirst timeaftertheunitwas
purchased.
2. Use the[ ]keyor[ ]keytoselect the“EnglishLetter”,
“EnglishA4”or“DeutschA4”, “ A4”.
10

3. Press theHOMEkey.
-Thedisplaywill changetotheselect language, thenthe
scannerwill beready.
-Thissetting will remainuntil itischangedtoanothersetting.
4.9.2. Setting theSCSIIDand Terminator
1. Press theOTHERSKey.
Enterssetting modes otherthanSCAN, COUNTER, orIMPRINT
and displaystheversion
2. Press theMODEKey.
Press theMODEKey[ ]todisplaytheSCSI ID, whichisthe
fourthsetting.
3. Press theSELECT[ ]Keyor[ ]Keytoselect thedesired
setting.
The[ ]Keymoves tothenext IDas shownbelow.
The[ ]Keymoves tothepreviousID.
11

4. Press theMODEKey[ ]toswitchtotheterminatorsetting.
To activetheSCSI IDsettings, press theHOMEKeytoreturnto
“READY”, thenturntheunitoff and on.
5. Press theSELECT[ ]Keyor[ ]Keytoselect thedesired
setting.
The[ ]Keymoves tothenext contentas shownbelow.
The[ ]Keymoves tothepreviouscontent.
Note:
-Ifthescanneristhelast device intheSCSI chain, thenthe
terminatorshouldbeset to“Enable”. But, undertheaboveSCSI
chainand scanner’sturn-off, theterminatorshouldbeattachedto
theSCSI connectoron thescanner.
-Setting theSCSI IDwill beactivatedafterturning thepowerOFF
and turning itONagain.
-Setting theterminatorwill beactivatedafterturning thepowerOFF
and turning itONagain.
5. SECTIONALVIEWS
5.1. ImageSensors, Motorsand Imprinters(Option)
5.2. Rollers
5.3. CircuitBoards
5.4. SensorBoardsand Switches
6. MECHANICALFUNCTION
6.1. PaperFeedMechanism
12

1. WhenPCoutputs thescanning-startcommand, theHopperlifts
until thepapercontacts thePaperFeedRoller.
2. TheConveyorMotoristransferredtotherotation oftheConveyor
Rollers, DriveRollersand ExitRoller.
3. ThePaperFeedMotordrives thePaperFeedRoller, the
Separation Roller, and theRetardRoller. ThePaperFeedRoller
and theSeparation Rolleralwaysrotate inthepaperfeeddirection
(). TheRetardRollerrotates against thepaperfeed
direction ( )whenthereismorethanonesheet betweenthe
Separation Rollerand theRetardRoller. Ontheotherhand when
thereisonlyonesheet orthereno sheet, theRetardRollerrotates
inthesamedirection as theFeed.
Note:
Thescannerhas amultiplesheet feedmodethat keepstheRetard
RollerseparatedfromtheSeparation Rollerwhenscanning
multiplefeeds.
4. Whentheleading edgeofasheet ispassedintothepaperfeed
route byrotating thePaperFeedRoller, thepaperpasses through
theSeparation Rollerand RetardRoller. Because theRetardRoller
isrotating against thefeeddirection, inadvertentmultiplefeeds
areprevented.
13

5. WhentheStarting Position Sensordetects thetop ofthefirst
page, thePaperFeedMotor, thePaperFeedRoller, theSeparation
Roller, and theRetardRollerarestopped. Whenthetop ofthe
paperreaches theFront-sideScanning Start-position, activating
theStarting Position Sensor, CISstarts toscanthedata on the
page. And theBack-sideScanning Startprocess issameas Front-
sideScanning.
6. WhentheWaiting Sensordetects theend ofthefirst page, the
PaperFeedMotorstarts torotate again. Asaresult, thesecond
pageispassedintothepaperfeedroute. Theprocess toseparate
thefollowing pages fromthesecond pageisthesameas thefirst
item(3) and (4).
7. WhentheWaiting Sensordetects thetop ofthesecond page, the
PaperFeedMotorstopstokeepthispagebetweentheWaiting
Sensorand Driving Roller1.
8. WhenthePCoutputs thescanning-startcommand toscanthe
second page, ThePaperFeedMotordrives thepaperintothe
paperfeedpathagain.
Step(5) to(8) arerepeatedforeachsubsequentpaperfeed.
9. FrontorBack Exitcanbeselectedusing thePaperPathSelector.
6.2. Manual FeedMechanismand ADFAdjustment
1. Bysetting theADF/manual feedSelectortotheManual position
you canseparate theRetardRollerfromtheSeparation Rollerand
scanonesheet orseveral sheets.
2. Bysetting theADF/manual feedSelectortotheADFADJ. position,
thecontact force betweentheRetardRollerand theSeparation
Rollergoes up, according totheincrementoftheADFADJ.
number. (1 2 3 4)
Note:
(1) Normally, whenscanning normal paper, set theADFADJ. to
position “2”or“3”.
(2) Incase adouble-feedproblemoccurswhenscanning rough
paperlike NCR, set ADFADJ. to“1”position.
(3) Whenajamoccursat thepaperfeedarea orifusing heavy
14

paper, set theADF/manual feedselectorto“4”.
-TheADF/manual feedselectormust beset inthechosenspecific
position forthissetting tofunction properly.
-Ifdoublefeedalarm beepsfrequently, changetheADF/manual feed
selector.
7. MAINTENANCE
7.1. Maintenance Chart
C:CleanR: Replace (x1000 sheets)
15

Description PartNo. 50 100 150 200 250 300
PaperFeedRoller PBDRA0064Z C C C C C R
Separation Roller PBDRA0065Z C C C C C R
Retard Roller PBDRA0066Z C C C C C R
Drive Roller1 PBDRX01S2065 C C C C C C
Drive Roller2 PBDRX01S2065 C C C C C C
Drive Roller3 PBDRX01S2065 C C C C C C
Conveyor Roller1-3 PBDRX02S2065 C C C C C C
StraightExitRoller PBDRX02S2065 C C C C C C
ExitRoller PBDRX03S2065 C C C C C C
Sensor Roller1 for KV-
S2065L PBDRA0013Y-J C C C C C C
for KV-
S2065W PBDRA0102X-J C C C C C C
Sensor Roller2 for KV-
S2065L PBDRA0112Y-J C C C C C C
for KV-
S2065W PBDRA0102X-J C C C C C C
CIS for KV-
S2065L EQ4R219Q1 C C C C C C
for KV-
S2065W EQ4R300Q1 C C C C C C
Free Roller PBDRA0029Z C C C C C C
Note1:
Theabovevalues foreachmaintenance itemareregisteredinthe
maintenance counter(RefertoSection 9), and theLCD informsthe
userwheneachcondition occurs. All othercounterscanbe
observedusing service mode.
Note2:
Thismaintenance schedulewas determinedaccording topaper
standards(A4orletter, 16lbcopierpaper), whichcanvarygreatly
betweenusers. Therefore, thevalues canalsovary.
Note3:
RollerexchangekitKV-SS009 (Rollerassembly, including Paper
FeedRoller, Separation Roller, and RetardRoller)canbeusedas a
replacement.
Thisproduct KV-SS009 issuppliedviasales route.
7.2. RollerCleaning
7.2.1. PaperFeedRoller, Separation Roller, Retard Roller
16

1. Turnoff thePower.
2. OpentheFrontdoor.
3. Cleanthesurfaces ofthePaperFeedRollerand Separation Roller
and Separation Rollerwithcleaning paper(KV-SS03).
4. Cleanthesurface oftheRetardRoller.
17

Note 1:
Make suretocleantheRetardRollerfromrighttoleft.
Iftherolleriscleanedfromleft toright, itmayslipoutofposition.
Note 2:
Aftercleaning theaboverollers, clear“CleanRollerWarning”on
OtherSetting Modeas showninSection 9.
7.2.2. Drive Rollerand Conveyor Rollers
1. Turnoff thePower.
2. OpentheFrontdoor.
3. CleantheDriverand ConveyorRollerswithcleaning paper(KV-
SS03), as showninFig. 7-3 (sameas cleaning thePlasticFree
Roller).
18

7.3. CISGlass, DocumentSensorsand DoubleFeedDetection
SensorsCleaning
1. OpentheFrontdoor.
2. CleantheCISglass using theaccessoryrollercleaning paper(KV-
SS03). Also, removethedirton thedocumentsensorsand double
feeddetection sensorswiththeblowerScanner(KV-S2065L/W)
has.
Note:
Whencleaning thebottomCISglass, do nottouchthetipofthe
plasticpointer(black) intheback oftheunit.
Ifthepaperpathselectorisset tothelowerside, itmaycause an
injury.
19

7.4. SensorRollerCleaning
1. OpentheFrontdoor.
2. CleantheSensorRollerwithcleaning paper(KV-SS03), as shown
inFig. 7-3.
Note:
IftheSensorRollerisremovedwhilecleaning, re-attachitafter
cleaning as follows.
7.4.1. Re-attachmentoftheSensor RollerAssembly
WhentheSensor Rollerisremovedfor cleaning theinsideofthescanner, reattachitas shown
below.
LowerSensor Roller:
1. Attachtherollerbyplacing thegearsidetotheleft sideofthe
scannerand inserting bothside’sbearingsintotheguidegrooves.
20