Panasonic KX-TD816CE User manual

Digital Super Hybrid System
KX-TD816CE
KX-TD1232CE
Added and Changed Features for
Installation Manual and Programming Tables
Vol. 4
In this manual, the last letters, “CE”, of each model number are omitted.
ROM Version: KX-TD816CE — P341E, P342E or later
KX-TD1232CE — P241E, P242E or later

2
Attention
●The ISDN Line Unit (KX-TD280 / KX-TD286) is in accordance with the European
Telecommunication Standards (ETS).
If your telephone company provides an ISDN service which follows standards other than
ETS, some ISDN features may not work properly.
(E.g. Charge Fee Reference, CLIP, COLP, etc.)
●To use the point-to-multi-point configuration with the KX-TD286, the number on the name
plate, which is on the back of the unit, must be ➃or later.

3
Table of Contents
Additions to the KX-TD816/1232
Section 1.3 Proprietary Telephones .................................................................................6
Section 1.4 Options
Message Unit (KX-TD190).................................................................................................7
Remote Unit (KX-TD198) ..................................................................................................7
Primary Rate Interface ISDN Expansion Unit (KX-TD290)..............................................8
Remote Card (KX-TD197)..................................................................................................8
DSS Console (KX-T7440 / KX-T7441 / KX-T7540 / KX-T7541) ....................................9
Add-on Key Module (KX-T7545) ......................................................................................9
Connection................................................................................................................10
Section 2.4 Optional Cards and Units Installation
Primary Rate Interface ISDN Expansion Unit Connection ................................................13
2.4.1 Location of Optional Cards and Units ...................................................................14
Installing the Expansion Unit (KX-TD290)........................................................................15
Installing the Message Unit (KX-TD190) / Remote Unit (KX-TD198).............................17
Remote Card (KX-TD197) Installation...............................................................................19
Section 3 Features
Calling / Connected Line Identification Presentation (CLIP / COLP)................................20
Connected Line Identification Presentation (COLR)..........................................................21
Integrated Services Digital Network (ISDN)......................................................................22
Multiple Subscriber Number (MSN) Ringing Service........................................................25
Off-Hook Monitor...............................................................................................................26
Ring Group..........................................................................................................................27
Section 4 System Programming
[148] Off-Hook Monitor.....................................................................................................28
[150] ISDN DDI Translation Table....................................................................................29
[151]-[152] ISDN DDI Ringing Assignment — Day / Night............................................30
[421] ISDN DDI / MSN Removed Digit / Added Number Assignment............................32
[447] MSN Assignment......................................................................................................34
[448]-[449] Extension Ringing Assignment — Day / Night for ISDN .............................35
[450] PRI Configuration.....................................................................................................37
[451] PRI Reference CO ....................................................................................................38
[452]-[453] ISDN Ring Service Assignment — Day / Night ............................................40
[509] Off-Hook Call Announcement (OHCA)...................................................................41
[617] CLIP / COLP Number Assignment for Extension ...................................................42
[618] CLIP / COLP Number Assignment for ISDN Extension.........................................43
[817] KX-TD197 Baud Rate Setting..................................................................................44
Changes
Section 2 Installation
2.4.9 System Connection........................................................................................................46
Section 3 Features
Automatic Route Selection (ARS)......................................................................................46
Call Forwarding – to CO Line.............................................................................................46
Call Transfer; Unscreened – to Extension...........................................................................46
Direct Dialling In (DDI)......................................................................................................46, 49
Direct Inward System Access (DISA).................................................................................46
Flexible Numbering.............................................................................................................47
Floating Station ...................................................................................................................47, 50
Module Expansion...............................................................................................................47, 52

4
Table of Contents
Outgoing Message (OGM)..................................................................................................47
Station Hunting....................................................................................................................47, 53
Station Message Detail Recording (SMDR).......................................................................47
System Programming and Diagnosis with Personal Computer...........................................47
Section 4 System Programming
4.1.3 Entering Characters.................................................................................................47, 54
[005] Flexible CO Button Assignment...............................................................................48, 58
[100] Flexible Numbering..................................................................................................48
[106] Station Hunting Type................................................................................................48, 59
[109] Expansion Unit Type ................................................................................................48, 61
[127] UCD Time Table.......................................................................................................48
[131] ISDN DDI Number / Phantom Extension Number Transformation.........................48
[213] DISA Delayed Answer Time....................................................................................48
[214] DISA Prolong Time..................................................................................................48
[215] Outgoing Message Time...........................................................................................48
[401] CO Line Group Assignment.....................................................................................48, 63
[417] CO Line Name Assignment......................................................................................48, 64
[418] ISDN Line Number Assignment ..............................................................................48, 65
[420] ISDN DDI Service Assignment................................................................................48
[610] ISDN DDI Number / Extension Number Transformation........................................48
[611] ISDN DDI Number / Floating Number Transformation...........................................48
[809] DISA Security Type..................................................................................................48
[810] DISA Tone Detection................................................................................................48
[811] DISA / TIE User Codes............................................................................................48
[812] DISA DTMF Repeat.................................................................................................48
[813] Floating Number Assignment...................................................................................48, 67
[814] Modem Standard.......................................................................................................48
[990] System Additional Information.................................................................................48, 69
Programming Tables for Added and Changed Features
[100] Flexible Numbering..................................................................................................78
[106] Station Hunting Type................................................................................................78
[109] Expansion Unit Type ................................................................................................78
[148] Off-Hook Monitor.....................................................................................................78
[150] ISDN DDI Translation Table....................................................................................79
[151]-[152] ISDN DDI Ringing Assignment — Day / Night............................................79
[401] CO Line Group Assignment.....................................................................................87
[417] CO Line Name Assignment......................................................................................88
[418] ISDN Line Number Assignment ..............................................................................88
[421] ISDN DDI / MSN Removed Digit / Added Number Assignment............................89
[447] MSN Assignment......................................................................................................90
[448]-[449] Extension Ringing Assignment — Day / Night for ISDN .............................90
[450] PRI Configuration.....................................................................................................96
[451] PRI Reference CO ....................................................................................................96
[452]-[453] ISDN Ring Service Assignment — Day / Night ............................................97
[509] Off-Hook Call Announcement (OHCA)...................................................................97
[617] CLIP / COLP Number Assignment for Extension ...................................................98
[618] CLIP / COLP Number Assignment for ISDN Extension.........................................99
[813] Floating Number Assignment...................................................................................99
[817] KX-TD197 Baud Rate Setting..................................................................................99
[990] System Additional Information ................................................................................100

Additions to the KX-TD816/1232

6
1.3 Proprietary Telephones
The following Panasonic proprietary telephones have become
available for the KX-TD816 and KX-TD1232.
Proprietary Description
Telephone
KX-T7425 Digital, jog dial, speakerphone,
24 CO
KX-T7433 Digital, 3-line LCD, jog dial,
speakerphone, 24 CO
KX-T7436 Digital, 6-line LCD, jog dial,
speakerphone, 24 CO
KX-T7450 Digital, jog dial, monitor, 12 CO
KX-T7520 Digital, jog dial, speakerphone,
12 CO
KX-T7531 Digital, 1-line LCD, jog dial,
speakerphone, 12 CO
KX-T7533 Digital, 3-line LCD, jog dial,
speakerphone, 12 CO
KX-T7536 Digital, 6-line LCD, jog dial,
speakerphone, 12 CO
KX-T7550 Digital, jog dial, monitor, 12 CO

7
*1: Available for the KX-TD816 only.
1.4 Options
Remote Unit (KX-TD198)*1
The Remote unit allows system programming and maintenance
from a remote location for the KX-TD816.
Central
Office
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Personal Computer
with Modem
Telephone Line
This unit requires using the Direct Inward System Access (DISA)
feature and recording an Outgoing Message for the KX-TD816.
DISA allows you to access a desired destination in the system
directly from an external telephone. Once you have accessed the
DISA line, just dial the extension number. If necessary, the
Outgoing Messages (OGM) for external callers and /or an OGM
for Timed Reminder can be recorded.
Message Unit (KX-TD190)*1
Central
Office
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Telephone Line

8*2: Available for the KX-TD1232 only.
1.4 Options
Remote Card (KX-TD197)*2
The Remote card allows system programming and maintenance
from a remote location for the KX-TD1232.
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Central
Office
Personal Computer
with Modem
Telephone Line
1 PRI ISDN line can be added.
The KX-TD290 Primary Rate Interface (PRI) ISDN Expansion
Unit adds one PRI ISDN line.
This unit can be only installed to the KX-TD1232 Master system.
When this unit is installed, CO lines 13 through 24 will become
unavailable if the Slave system is operating.
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Primary Rate Interface ISDN Expansion Unit (KX-TD290)*2
Note This unit can be installed with the KX-TD280 or KX-TD286, but not with the KX-TD180
or KX-TD184.

9
1.4 Options
DSS Console (KX-T7440 / KX-T7441 / KX-T7540 / KX-T7541)
Add-on Key Module (KX-T7545)
Adds 12 CO buttons to a KX-T7500 series telephone.
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Paired Telephone
(Proprietary
Telephone)
DSS Console
Pair
KX-T7540
6
5
4
3
2
1
12
11
10
9
8
7
123
6
5
4
789
0
6
5
4
3
2
1
12
11
10
9
8
7
123
6
5
4
789
0
ABC DEF
MNO
JKL
GHI
PQRS TUV WXYZ
24
23
22
21
20
19
18
17
16
15
14
13
MODE
SELECT
FWD/DND
AUTO ANS/
MUTE
AUTO DIAL/
STORE
MESSAGE
FLASH
REDIAL
HOLD
SP-PHONE
PAUSE
TRANSFER
CONF
INTERCOM
PROGRAM
Add-on Key Module
Note The KX-T7536 and KX-T7540 are illustrared as an example.

10
1.4 Options
Connection
■ KX-T7440 / KX-T7441 and KX-T7400 series telephones
You can attach a KX-T7440 Digital DSS Console or KX-T7441 Attendant Console
and a KX-T7400 series telephone. Use the attached plate and screws.

11
1.4 Options
■ KX-T7540 / KX-T7541 and KX-T7500 series telephones
You can attach a KX-T7540 Digital DSS Console or KX-T7541 Attendant Console
and a KX-T7500 series telephone. Use the attached plate and screws.
1. Open the cover. 3. Attach the DSS console to your
telephone with the screws.
2. Remove (A) and (B) as shown
below. 4. Close the cover.
A
B

12
1.4 Options
■ KX-T7545 and KX-T7500 series telephones
To use the KX-T7545 Add-on Key Module, you must connect it to a KX-T7500 series
telephone. Use the attached screw.
1. Open the cover. 3. Insert the cable into the
connector.
2. Attach the KX-T7545 to your
telephone with the screw. 4. Close the cover.
Remove as
shown. A
A

13
2.4 Optional Cards and Units Installation
Primary Rate Interface ISDN Expansion Unit Connection
The KX-TD290 Primary Rate Interface (PRI) ISDN Expansion
Unit adds one PRI ISDN line.
When this unit is installed to the system, the maximum number of
available CO lines is limited to 42. CO lines 13 through 24 will
become unavailable if the Slave system is operating.
One PRI ISDN line adds 30 CO lines (CO 25 through CO 54) to the
system.
This unit can be only installed to the KX-TD1232 Master system.
The following procedures can be used to install either an 8-Station
Line Unit (KX-TD170), 16 SLT Line Circuit Unit (KX-TD174),
4-CO Line Unit (KX-TD180), E&M (TIE) Line Unit (KX-TD184),
ISDN 2-S0 Line Unit (KX-TD280), ISDN 6-S0 Line Unit (KX-
TD286) or Primary Rate Interface ISDN Expansion Unit (KX-
TD290). System programming is required for unit location
identification.
Default KX-TD816: bottom = 4-CO Line Unit,
top = 8-Station Line Unit
KX-TD1232: bottom = 4-CO Line Unit,
middle and top = 8-Station Line Unit
Programming Reference
Section 4, System Programming — in this manual
[109] Expansion Unit Type
Feature Reference Section 3, Features — in this manual
Module Expansion

14
D1232
Panasonic
Expansion Unit for KX-TD1232
A maximum of two 8-Station Line Units (KX-TD170) or 16 SLT
Line Circuit Units and/or one CO Line/E&M (TIE) Line/ISDN
Line Unit (KX-TD180, KX-TD184, KX-TD280, KX-TD286) can
be installed to any expansion area. The PRI ISDN Line Unit (KX-
TD290) can be installed with the KX-TD280 or KX-TD286, but
not with the KX-TD180 or KX-TD184. You must use the KX-
TD170/174-②when you install the KX-TD290. The former KX-
TD170/174 does not work properly with the KX-TD290.
Please see the back of the unit and check “②” is marked.
Area 3
Area 2
Area 1
Unit Connectors
Remove the front
cover plate(s).
Max. 2 units
8-Station Line Unit,
KX-TD170
or
16 SLT Line Circuit
Unit, KX-TD174
• 4-CO Line Unit,
KX-TD180
• E&M (TIE) Line Unit,
KX-TD184
• 2-ISDN S0 Line Unit,
KX-TD280
• 6-ISDN S0 Line Unit,
KX-TD286
1-PRI ISDN Line Unit,
KX-TD290
This unit can be
installed with the KX-
TD280 or KX-TD286,
or individually.
The locations of the optional units are shown below.
Precautions To protect the printed circuit boards (P-boards) from static electricity, do
not touch parts on the P-boards in the main unit and on the optional units.
ISDN unit (KX-TD280, KX-TD286, KX-TD290) installation;
The ISDN unit should not be installed only to the Slave system.
Note •When starting the system for the first time or performing System Data
Clear, the location application will use the actual installation settings
instead of the system default settings.
•System Programming is required for location identification.
Refer to [109] “Expansion Card/Unit Type” in this manual.
Default:
KX-TD1232:Area 1= 4-CO Line Unit, Area 2, 3= 8-Station Line Unit
One of the following units
2.4.1 Location of Optional Cards and Units
②
MODEL NO.KX-TD170
Example

15
Installing the Expansion Unit (KX-TD290)*
Panasonic
D1232
DIGITAL SUPER HYBRID SYSTEM
2. Connect the cabinet cord to the
connector in the main unit firmly.
1. Loosen the two screws on the cover plate.
Insert your fingers into the slits to remove
the cover plate.
Note Any of the cover plates can be
removed, as needed.
3. Hook the cabinet onto the main unit
and slide the cabinet to the left until it
is secured.
Slit Slit
4. Loosen the outside screw and slide the
cover to the right.
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Panasonic
D1232
DEGITAL SUPER HYBRID SYSTEM
Panasonic
D1232
DIGITAL SUPER HYBRID SYSTEM
Outside screw
5. Secure the inside screw (included) to fix
the cabinet to the main unit.
Panasonic
D1232
DIGITAL SUPER HYBRID SYSTEM
Inside screw
6. Prepare the required plugs. Two 4-pin
plugs are included with the KX-TD290.
Note Be sure to attach the inside screw
securely, or the unit will not work
properly.
RB
RA TB TA
or
*: Available for the KX-TD1232 Master system only.

16
Programming Reference
In this manual
Section 4, System Programming
[109] Expansion Unit Type
Cut here
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Note • If two or three expansion units are
installed, cut the cabinet covers on the
lower cabinets to allow the cords from
the upper cabinets to go down through
the cabinet covers. To protect the
cords, smooth the cut edges.
11. Fix the cords to the wall as
shown here, so that the front
cover can be opened.
Cord holder
D1232
DIGITAL SUPER HYBRID SYSTEM
Panasonic
7. Insert the plug into a jack on the unit.
Connect an earth wire to the earth terminal
on the extension expansion unit.
Installing the Expansion Unit (KX-TD290)*
8. Tie all of the cords into a bundle. If other
cords are exposed from the upper cabinets,
tie them also.
9. Close the cabinet cover and secure the
outside screw.
10. Cover the cords with the cord holder
(included with the main unit).
Panasonic
2CO
8
7
6
5
4
3
2
1
View of TEL Jack
RB
RA
TB
TA
ISDN
DIGITAL SUPER HYBRID SYSTEM
PRI
To Terminal Board or Modular
Jacks from the Central Office
*: Available for the KX-TD1232 Master system only.

17
2. Connect the cabinet cord to the
connector in the main unit firmly.
1. Loosen the two screws on the cover
plate. Insert your fingers into the slits
to remove the cover plate.
Note There are two cover plates. Any of
them can be removed, as needed.
3. Hook the cabinet onto the main unit
and slide the cabinet to the left until it
is secured.
D816
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
3. Remove the cover plate and connect the
cabinet cord to the connector in the main
unit firmly.
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Slit
Slit
Installing the Message Unit (KX-TD190)* /
Remote Unit (KX-TD198)*
2. Attach the expansion unit to the Message
or Remote unit as shown below. Be sure
to connect the cabinet cords by inserting
the expansion unit cabinet cord through
the slot in the Message or Remote unit.
Expansion unit cabinet cord
Message/Remote unit
cabinet cord
*: Available for the KX-TD816 only.
1. Remove the front cover of the Message or
Remote unit.
To install only the Message unit
or Remote unit To attach another expansion unit to the Message or Remote unit and install them to
the system

18
4. Hook the cabinets onto the main unit and
slide the cabinets to the left until they are
secured.
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Panasonic
Cord holder
Installing the Message Unit (KX-TD190)* /
Remote Unit (KX-TD198)*
*: Available for the KX-TD816 only.
7. Tie all of the cords into a bundle. If other
cords are exposed from the upper cabinets,
tie them also.
8. Close the cabinet cover and secure the
outside screw.
9. Cover the cords with the cord holder. If
two cabinets are connected together and
attached to the main unit, use the cord
holder included with the Message or
Remote unit.
10. Fix the cords to the wall as shown here, so
that the front cover can be opened.
5. Loosen the outside screw of the expansion
unit and slide the cover to the right.
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Outside screw
6. Secure the inside screw (included with the
Message or Remote unit) to fix the cabinet
to the main unit.
Panasonic
D816
DIGITAL SUPER HYBRID SYSTEM
Inside screw

19
Remote Card (KX-TD197) Installation*
*: Available for the KX-TD1232 only.
To perform system programming and maintenance from a remote
location using a personal computer (PC), install the Remote card
(KX-TD197).
1. Open the front cover.
2. Insert the top side of the Remote card into
the two hooks on the main unit.
3. Press down on the two corners of the
bottom side of the Remote card.
4. Connect the cord to the Remote card
connector.
Programming Reference
Section 4, System Programming – in this manual
[817] KX-TD197 Baud Rate Setting
Feature Reference Section 3, Features – in this manual
System Programming and Diagnosis with Personal Computer
KX-TD196 REMOTE
Remote Card

C3 Features
20
C alling / Connected Line Identification Presentation (CLIP / COLP)
Description Calling Line Identification Presentation (CLIP) enables showing
the calling party’s number on the display of the called party’s
telephone when a call is received.
Connected Line Identification Presentation (COLP) enables
showing the called party’s number on the display of the calling
party’s telephone when the called party answers a call.
These features are one of ISDN’s services.
To use the CLIP or COLP service, number assignments are required
as follows:
• CLIP/COLP number for each outside line
• CLIP/COLP number for each extension
Conditions • The CLIP service for outgoing CO calls can be restricted by System
Programming (CLIR: Calling Line Identification Restriction).
• The number actually sent to the calling or called party may be different
from the system programmed number. It depends on the contract with
your ISDN supplier.
Programming References
Section 4, System Programming
— Added and Changed Features for Installation Manual and Programming Tables
[418] ISDN Line Number Assignment
[419] ISDN Outgoing CLIR Service Assignment
— In this manual
[617] CLIP / COLP Number Assignment for Extension
[618] CLIP / COLP Number Assignment for ISDN Extension
[990] System Additional Information, Field (46)
Feature References Section 3, Features
– Added and Changed Features for Installation Manual and Programming Tables
Calling Line Identification Restriction (CLIR)
— In this manual
Connected Line Identification Restriction (COLR)
Operation Reference DPT Features
—Added and Changed Calling / Connected Line Identification Presentation (CLIP / COLP)
Features for
User Manual Vol. 5