Panasonic KX-TVM50 User manual

Document Version 2.1 2008/04
Getting Started
Voice Processing System
Model No. KX-TVM50
KX-TVM200
Thank you for purchasing a Panasonic Voice Processing System. This manual shows you how to install and
programme this product so that you can operate the basic features.
For detailed information, refer to the Installation Manual.
KX-TVM50/KX-TVM200: Version 2.1 (Main Software Version 2.50 or later)

Table of Contents
1 Before Installation ....................................................................................3
1.1 Unpacking ..........................................................................................................................3
1.2 Names and Locations .......................................................................................................4
2Installation ................................................................................................6
2.1 Installation Overview ........................................................................................................6
2.2 Removing the Cable Cover ..............................................................................................7
2.3 Opening the Front Cover ..................................................................................................8
2.4 Removing the Dummy Cover Plates ...............................................................................9
2.5 Installing Optional Cards in the KX-TVM50 ..................................................................10
2.6 Installing Port Cards in the KX-TVM200 ........................................................................13
2.7 Connecting the KX-TVM50 to the KX-TDA30 ................................................................16
2.8 Connecting the KX-TVM200 to the KX-TDA100 ............................................................17
2.9 Connecting the VPS to a PC or LAN .............................................................................18
2.10 Frame Earth Connection ................................................................................................19
2.11 Connecting the AC Adaptor ...........................................................................................20
2.12 Securing the Cables ........................................................................................................22
2.13 Initialising the VPS During Installation .........................................................................24
2.14 Closing the Front Cover .................................................................................................25
2.15 Attaching the Cable Cover .............................................................................................26
2.16 Wall Mounting ..................................................................................................................27
2.16.1 Wall Mounting the VPS ..................................................................................................27
2.16.2 Wall Mounting the AC Adaptor .......................................................................................28
3 KX-TDE and KX-TDA Series PBX Programming for DPT
Programming ..........................................................................................32
3.1 Assignment of VM (DPT) Group ....................................................................................32
3.2 Assignment of VM (DPT) Extension Ports ....................................................................33
4 Programming the VPS ...........................................................................34
4.1 Installing KX-TVM Maintenance Console ......................................................................34
4.2 Starting KX-TVM Maintenance Console ........................................................................36
4.3 Quick Setup .....................................................................................................................39
4.4 LAN Settings ....................................................................................................................48
4.5 E-mail Integration Settings .............................................................................................49
5 System Prompts Customisation ...........................................................51
5.1 System Prompts Customisation ....................................................................................51
2Getting Started Document Version 2.1 2008/04

1 Before Installation
1.1 Unpacking
The following items are included with the VPS.
KX-TVM50 KX-TVM200
Main Unit 1 1
AC Adaptor 1 1
AC Cord 1 1
Screws (Wall Mounting) 5 5
Washers (Wall Mounting) 5 5
Cable strap 1 1
CD-ROM 1 1
Necessary Tools (not supplied)
Twisted pair 4-conductor cables are needed for connecting the VPS to the PBX. For the KX-TVM50, twisted
pair 2-conductor cables are needed if using Inband or None Integration.
A USB cable is needed when connecting the VPS to the PC that will used for programming via the KX-TVM
Maintenance Console.
Document Version 2.1 2008/04 Getting Started 3
1.1 Unpacking

1.2 Names and Locations
KX-TVM50
5
6
4
8
9
10
11
7
13
12
14
3
2
1
1. RUN Indicator
2. ALARM Indicator
3. Dummy Cover Plates (for Port Card Slots 2 and 3)
4. Factory-installed Jacks
5. RESET Button
6. SHUTDOWN Button
7. Mode Switch
8. USB Port
9. Dummy Cover Plate (for LAN Interface Card)
10. Dummy Cover Plate (Reserved)
11. Dummy Cover Plate (for Modem Card)
12. Earth Terminal
13. DC IN
14. Power Switch
1
324
1. Main Board
2. Front Cover
3. Factory-installed Flash Memory Card
4. Cable Cover
4 Getting Started Document Version 2.1 2008/04
1.2 Names and Locations

KX-TVM200
7
6
5
4
8
911
10
12
3
2
1
1. RUN Indicator
2. ALARM Indicator
3. Dummy Cover Plates (for Port Card
Slots 1 to 6)
4. RESET Button
5. SHUTDOWN Button
6. Mode Switch
7. LAN Port
8. USB Port
9. Dummy Cover Plate (for Modem Card)
10. Earth Terminal
11. DC IN
12. Power Switch
1
23 4
1. Main Board
2. Front Cover
3. 3.5" Hard Disk Drive
4. Cable Cover
Document Version 2.1 2008/04 Getting Started 5
1.2 Names and Locations

2 Installation
2.1 Installation Overview
The following is an overview of the steps needed to prepare the VPS hardware for use. Refer to the Installation
Manual when installing optional cards or hardware.
CAUTION
The information below is only intended as an overview of the installation process. When installing the VPS,
refer to the information provided in this document or to the Installation Manual for detailed instructions.
1. Remove the cable cover.
2. KX-TVM200 only: Install the port cards.
3. Connect the VPS to the appropriate extension ports of the PBX.
4. Connect the VPS to the PC to be used for programming.
5. Connect the VPS to earth.
6. Connect the AC adaptor to the VPS and to the power outlet.
7. Secure the cables.
8. Initialise the VPS.
9. Attach the cable cover.
10. Wall mount the VPS and AC adaptor.
6 Getting Started Document Version 2.1 2008/04
2.1 Installation Overview

2.2 Removing the Cable Cover
The model shown here is the KX-TVM200, however this procedure is the same for the KX-TVM50.
Push the release button in the direction shown below (1), and slide the cable cover in the direction shown
below (2). Turn the cable cover away from the unit and remove it.
1
Release Button
Cable Cover
Document Version 2.1 2008/04 Getting Started 7
2.2 Removing the Cable Cover

2.3 Opening the Front Cover
The model shown here is the KX-TVM200, however this procedure is the same for the KX-TVM50.
For KX-TVM50:
This procedure is not necessary if you do not plan on installing optional cards in the KX-TVM50.
1. Remove the 3 screws.
Screw
2. While holding both tabs located on the sides of the front cover, swing the cover open as shown.
3. To remove the front cover completely during installation, hold the front cover open at a 45° angle, then lift
the cover away from the unit as shown.
8 Getting Started Document Version 2.1 2008/04
2.3 Opening the Front Cover

2.4 Removing the Dummy Cover Plates
The model shown here is the KX-TVM200, however this procedure is the same for the KX-TVM50.
For KX-TVM50:
This procedure is not necessary if you do not plan on installing optional cards in the KX-TVM50.
Remove the appropriate dummy cover plates from the main unit using cutting pliers, as shown below.
Dummy Cover Plate
CAUTION
For safety reasons, smooth the cut edges after removing the dummy cover plates.
Document Version 2.1 2008/04 Getting Started 9
2.4 Removing the Dummy Cover Plates

2.5 Installing Optional Cards in the KX-TVM50
Follow these steps if you plan to install an optional KX-TVM502 2-Port Hybrid Expansion Card or
KX-TVM594 LAN Interface Card in the KX-TVM50.
Installing a 2-Port Hybrid Expansion Card
1. Position the front of the card so that the jacks fit in the open slot. Holding the card firmly in place, lower the
other end of the card so that the card’s hole fits over the extension bolt.
CAUTION
When installing optional cards, do not put pressure on the main board. Doing so may result in damage
to the VPS.
2
1
Extension Bolt
2. Insert and tighten the screws as shown.
Screw
10 Getting Started Document Version 2.1 2008/04
2.5 Installing Optional Cards in the KX-TVM50