Panasonic KX-TDE100 User manual

2/4/2010 1
Rev2
Cbeyond SIP Trunks Configuration Guide
PBX Platform: KX-TDE/NCP

2/4/2010 2
Rev2
Overview
This document describes the configuration procedures required for the KX-TDE100/200/600 and
NCP500/1000 to make full use of the capabilities of Cbeyond SIP Trunks Services.
The SIP trunks services of the TDE/NCP PBX are provided through virtual CO line cards (V-
SIPGW16) which are designed to be easily integrated into an Internet Telephony Service
provided by an ITSP (Internet Telephony Service Provider).
This guide describes the specific configuration items for the virtual SIP Gateway card in addition
to the PBX basic configuration related to SIP trunks functionality. It also describes basic Network
configuration to familiarize dealers with the network setup. It does not describe the purpose and
use of all configuration options on the virtual SIP Gateway card. For those details, see the KX-
NCP500/1000 and KX-TDE100/200/600 Programming Manual for Virtual SIP CO Line Card and
the KX-TDE100/200/600 and KX-NCP500/1000 Manuals available from Panasonic
Communication Solutions.
DSP card and Activation keys
9The PBX has to be equipped with a DSP card in order to provide
communication between the TDM side of the PBX and the SIP trunks.
9Activation keys for SIP-Trunks has to be installed in the PBX to provide the
SIP-trunks functionality
To check the number of activation keys installed into the PBX and add new licenses
please refer to Page 12 in this guide

2/4/2010 3
Rev2
Architecture Overview
The following diagram illustrates simple VOIP networks connecting the TDE/NCP PBX:
The Case of Cbeyond Setup: Cbeyond will provide its services over a dedicated Circuit
terminated at the CPE device
MPR IP Address 192.168.0.101
VOIP IP Address 192.168.0.102
Default GW 192.168.0.1
sipconnect.mia0.cbeyond.net

2/4/2010 4
Rev2
Basic V-SIPGW16 Settings for Cbeyond
1-Install the PBX Maintenance console into your PC
The maintenance console should be available to certified dealers; Dealers can get the
latest version of the UPCMC from www.btsdealer.com
2- Connect to the PBX
oStart the UPCMC
oClick Connect and choose the method of connection using either LAN , RS-
232, Modem, or USB to Connect to your PBX for interactive configuration
** We will be using the LAN method throughout this guide**
Provide the IP address of the MPR card and the password of the INSTALLER Level

2/4/2010 5
Rev2
oGo to 1-Configuration, 1-Slot, move your mouse over the MPR card and
select the card property
Make sure that the default gateway should be the end router LAN IP address
Make sure that you have a valid DSP-VOIP LAN address

2/4/2010 6
Rev2
3- Installing V-SIP W16 card
oGo to 1-Configuration, 1-Slot, move your mouse towards the IPCMPR virtual
shelf and click on select shelf
Highlight the V-SIPGW16 card from the cards list in the left side
oDrag the VSIPGW16 card into the trunk portion of the virtual shelf by using
the PC mouse lift button

2/4/2010 7
Rev2
oRelease the Mouse lift button and click Yes on the dialogue box
oTake the V-SIPGW16 card OUS in order to be able to enter the following
settings
4-Configuring the VSIP-GW16 card
oMove the mouse over the VSIPGW16 card and choose shelf property
The following settings are required for Cbeyond SIP trunk services on the shelf
property:

2/4/2010 8
Rev2
** (SIP Client Port Number = 5060 and NAT-Keep Alive Packet sending
ability=Enable)
oClick Apply and then OK
oMove you mouse over the VSIPGW16 card and choose Card property
oClick on Common settings
oDNS Server IP address method is Manaul
oProvide your Cbeyond DNS serevers IP addresses. You can find the DNS
information in your Cbeyond Install profile by logging onto
CbeyondOnline.net or from Cbeyond Service Coordinator

2/4/2010 9
Rev2
oClick Apply and then OK
oClick Cancel on the card property- Virtual SIP gateway screen to exit this
screen
oMove you mouse over the VSIPGW16 card and choose port property

2/4/2010 10
Rev2
Basic Channel setup:
Please locate the SIP Connect Settings details in your Install Profile from
Cbeyond
oMain tab:According to the account info above, we need to configure the
Basic Channel Port as follows:
1- Port 1 channel attribute = Basic channel
2- Provider name= Cbeyond
3- SIP Server Name= SIPConnect Domain= “sip-proxy.mia0.cbeyond.net”
4- SIP server port number =5060
5- SIP service Domain = “sipconnect.mia0.cbeyond.net”
6- Subscriber number = 1234567890 (Optional)
oAccount tab:
1- user name == PBX Username==1234567890
2- Authentication ID== same as PBX Username 1234567890
3- Password == PBX Password=RNJORNJO ÆCase Sensitive Entry
oRegister Tab:
1- Register abilty== Enable
2- Register sending interval==3600sec
3- Unregister ability when port INS==Enable
4- Register server name/IP address== Blank (No settings)
5- Register server port==5060
oNAT Tab:
Same as default
oOption Tab:
Same as default
oCalling Party tab:
Same as default
oCalled party Tab:
Same as default
oVoice/Gax Tab:
1- IP Codec priority (1st = G.729A, 2nd= G.711u, 3rd=None)
2- Fax Sending method= G.711 Inband
3- Fax Detection Ability= Enable
1234567890
Outbound Proxy
sip-proxy.mia0.cbeyond.net

2/4/2010 11
Rev2
oRTP/RTCP Tab:
Same as default
oT.38, T.38 Option
Same as default
oDSP, Supplementry services:
1- CLIR = Yes
2- CNIP (Send) = Yes
3- CNIP (Receive) = Yes
Additional DID’s
Please set the channel attribute for number of ports depending on the number of
active SIP lines as”additonal channel for channel 1”
Since there are 16 active SIP lines, the number of V-SIPGW ports to be set as
an”additonal channel for channel 1”will be 15 ports
1234567890

2/4/2010 12
Rev2
Essential PBX Configuration:
To Assign the DID numbers destinations, Go to 10-3.CO & Incoming CallÆDID table
Please locate your DID information in the Cbeyond Install Profile under the Trunk
Group Information section
Important note:
Make sure that you provide the 10 digits DID number in the DID number field to be able to
make use of the additional DID’s assigned by the Provider.
SIP trunks Activation keys:
1- The DSP card installed onto the PBX MPR Card has preinstalled number of SIP
trunks activation keys (DSP4 and DSP16 have 4 IP trunks and DSP64 has 16 IP
trunks)
2- To obtain additional activation keys, you need to purchase the appropriate
activation key codes (For IP Trunks) and access the Key Management System. You
can download the activation keys as an activation key file from the Key
Management System. To download the activation keys, enter the MPR ID number
shown on the IPCMPR Card in the PBX, and activation key number and registration
ID provided on each activation key code.
3- To check the Number of Activation Keys Installed into your system
Go to 1- Configuration, 1-Slot, click on Activation Keys (Top of the PBX image)

2/4/2010 13
Rev2
Minimum System Software requirements:
UPCMC V5.1.2.3(Latest as of 1/14/10)
NCP V1.0101 and higher
TDE 100/200/600 V 2.0104 and higher
Useful Hints:
1- Update your system software once the update is available through the Dealer
website to make use of added features and improved functionality
2- Update your PCMC (Maintenance Tool) with the latest version available on the BTS
website and through Panasonic Tech support department
3- Back up your configuration file with the Good known settings
4- Consult with your network administrator prior to installation to guarantee a smooth
setup for your system over the existing network