Panduit smartzone G5 User manual

G5 PDU User Manual

SMARTZONE G5 USER MANUAL
1
Contents
Figures............................................................................................................................4
Section 1 – System Overview .........................................................................................6
Intelligent Network Controller.......................................................................................6
Connecting the PDU to a LAN Ethernet Port...............................................................6
Connecting the PDU to a Computer Serial Port...........................................................7
Setup Serial Communication....................................................................................8
Section 2 – Web Graphical User Interface (GUI) Configuration....................................11
Internet Protocol (IP) Address ...................................................................................11
Web Configuration.....................................................................................................11
Supported Web Browsers......................................................................................11
Logging in to the Web Interface.............................................................................11
Introduction to the Web GUI......................................................................................12
Menu Dropdowns...................................................................................................15
Introduction to the Dashboard ...................................................................................16
Section 3 – Simple Network Management Protocol (SNMP).........................................18
SNMP Management Configuration............................................................................18
Configuring Users for SNMP v3 Communications.....................................................22
Configuring SNMP Traps...........................................................................................24
Section 4 -Connecting to CLI Connection ...................................................................25
Supported Commands...........................................................................................25
Connecting to the CLI through the serial interface.....................................................26
Section 5 – Local Display..............................................................................................28
OLED Display............................................................................................................28
Menu Mode............................................................................................................29
OLED Menu Structure ...............................................................................................30
Main Menu Selections............................................................................................31

SMARTZONE G5 USER MANUAL
2
Setup Menu............................................................................................................31
Sensors Menu ...........................................................................................................42
Section 6 – User Access...............................................................................................44
Access Types.........................................................................................................46
Setting up the system for Radius Authentication.......................................................48
Configuring the system with LDAP Server Settings...................................................49
Section 7 – Daisy Chain Configuration..........................................................................53
Daisy-Chain Overview...............................................................................................53
Daisy-Chain Setup.....................................................................................................53
RNA (Redundant Network Access) Functionality ......................................................53
RNA Setup.................................................................................................................54
Section 8– Web GUI configuration................................................................................56
Setting Time and Date on the PDU............................................................................56
G5 iPDU Outlet Power Sequence Setup ...................................................................56
Outlet Power Management........................................................................................60
Setting Metering Thresholds......................................................................................61
Section 9 – Connecting and Configuring Optional Hardware........................................73
Accessory Hardware Overview..................................................................................73
Configuring Environmental Sensors ..........................................................................76
Section 10 – Rack Access Control................................................................................77
Configuring Rack Access Control..............................................................................78
Configuring User for Local Rack Access. ..................................................................81
Warranty and Regulatory Information............................................................................83
Warranty Information.................................................................................................83
Regulatory Information ..............................................................................................83
Support and Other Resources.......................................................................................84
Accessing Panduit Support........................................................................................84
Acronyms and Abbreviations.........................................................................................85
Documentation Feedback .............................................................................................88

SMARTZONE G5 USER MANUAL
3
Appendix A: CLI Commands.........................................................................................89
Appendix B: Sensor Configuration................................................................................97
Appendix C: Firmware Update Procedure...................................................................101
USB Method............................................................................................................101
Web Interface Method .............................................................................................101
FTPs Method...........................................................................................................103
Bootloader Mode.....................................................................................................104
Firmware Recovery with Bootloader Mode..............................................................104
Appendix D: System Recovery....................................................................................105
Upgrade Configuration with Bootloader Mode.........................................................105
Appendix E: PDU Alarms............................................................................................106
Trap Codes assigned to Alarms List........................................................................108
Appendix F: Horizontal Intelligent Network Controller Replacement...........................113
Appendix GF: Vertical Intelligent Network Controller Replace or Rotate 180°............116

SMARTZONE G5 USER MANUAL
4
Figures
Figure 1: Ethernet Port for Network Connection..............................................................7
Figure 2: Locate Reset Button.........................................................................................8
Figure 3: Port Setup Settings..........................................................................................9
Figure 4: Login Page.....................................................................................................12
Figure 5: Landing Page/Dashboard ..............................................................................13
Figure 6: Power Summary Page...................................................................................16
Figure 7: Outlet Monitoring Page ..................................................................................16
Figure 8: Environmental Page.......................................................................................17
Figure 9: Security Page.................................................................................................17
Figure 10: Power Threshold............................................ Error! Bookmark not defined.
Figure 11: Energy Threshold........................................... Error! Bookmark not defined.
Figure 12: Phase Current Alarm Threshold..................... Error! Bookmark not defined.
Figure 13: Phase Voltage Alarm Threshold..................... Error! Bookmark not defined.
Figure 14: SNMP Management.....................................................................................18
Figure 15: SNMP General.............................................................................................19
Figure 16: SNMP Port...................................................................................................20
Figure 17: Setup SNMP Port and Trap Port..................................................................20
Figure 18: Define SNMP V1/V2c User..........................................................................21
Figure 19: Edit V1/2c Manager......................................................................................21
Figure 20: SNMP V3 Manager......................................................................................22
Figure 21: SNMP V3 Edit..............................................................................................23
Figure 23 - Remote Control Setting................................. Error! Bookmark not defined.
Figure 26 - AutoLock Setting........................................... Error! Bookmark not defined.
Figure 24: Connect the RJ-45 end of the cable to the Serial+RS485-1 connector........26
Figure 25: Serial Cable Pinout ......................................................................................27
Figure 27: the OLED Display Orientation......................................................................28
Figure 28: OLED Menu Structure..................................................................................30
Figure 29: Main Menu Selections..................................................................................31
Figure 30: Setup Menu..................................................................................................31
Figure 31: Network Submenu........................................................................................32
Figure 32: Device Submenu..........................................................................................33
Figure 33: Screen Submenu .........................................................................................34
Figure 34: Language Submenu.....................................................................................35
Figure 35: USB Submenu .............................................................................................36
Figure 36: Units Submenu.............................................................................................37
Figure 37: Alarms Menu................................................................................................38

SMARTZONE G5 USER MANUAL
5
Figure 38: Power Menu.................................................................................................38
Figure 39: Device Submenu..........................................................................................39
Figure 40: Phase Submenu...........................................................................................40
Figure 41: Breaker Submenu........................................................................................41
Figure 42: Outlet Submenu...........................................................................................42
Figure 43: Sensors........................................................................................................43
Figure 44: Changing Your Password.............................................................................44
Figure 45: After Login....................................................................................................45
Figure 46: Change User Password...............................................................................45
Figure 47: Change Password........................................................................................46
Figure 48: User Settings................................................................................................48
Figure 49: Radius Configuration....................................................................................49
Figure 50: LDAP Configuration .....................................................................................50
Figure 51: Enable Role Privileges.................................................................................51
Figure 52: Test LDAP Configuration..............................................................................52
Figure 54:Control & Manage PDU.................................................................................57
Figure 55: Outlet Control Enabled.................................................................................57
Figure 56: Edit Outlets...................................................................................................58
Figure 57: One-Delay Time...........................................................................................59
Figure 58: Saved Sequence..........................................................................................59
Figure 59: Sensor Ports for vertical PDU ......................................................................75
Figure 60: Sensor Ports for Horizontal PDU..................................................................76
Figure 61 - Rack Access Control...................................................................................77
Figure 62 - Actions........................................................................................................79
Figure 63 - Smart Rack.................................................................................................80
Figure 64 - Remote Control...........................................................................................80
Figure 65 – AutoLock....................................................................................................81
Figure 66: Upload Firmware........................................................................................102
Figure 67: Uploading Firmware...................................................................................103
Figure 68: Unscrew Intelligent Network Controller......................................................113
Figure 69: Remove Intelligent Network Controller from PDU......................................114
Figure 70: Inserting New Intelligent Network Controller..............................................115
Figure 71: Removing Top and Bottom Screw from Intelligent Network Controller.......116
Figure 72: Disconnecting and Reconnecting the Intelligent Network Controller..........117

SMARTZONE G5 USER MANUAL
6
Section 1 – System Overview
Intelligent Network Controller
The Panduit G5 Intelligent PDUs have an integral, hot swappable Intelligent Network
Controller. The Intelligent Network Controller contains an OLED display, control buttons,
USB Interface, Serial and Sensor ports, and a recessed Reset Button.
Reset Button
Pressing the Reset Button only reboots the Intelligent Network Controller. It does not
change the Energy (kWh) value and does not affect the output voltage. It also does not
reset the Intelligent Network Controller to factory default settings.
Using the Reset Button
Press and hold the Reset Button for 8 seconds to recover from an Intelligent Network
Controller communication failure.
Connecting the PDU to a LAN Ethernet Port
The PDU is defaulted to DHCP. If you are connected to a network with a DHCP server,
the PDU automatically get an IP address and display it on the LCD screen. If there is no
DHCP server, the default IP address is 192.168.0.1, which will be displayed on the
PDU.
Connecting the PDU to a LAN provides communication through an Internet or Intranet
connection. You can monitor the PDU from any computer connected to the same
network.
1. Locate an Ethernet cable.
2. Connect one end of the cable to the Ethernet port on the PDU (see Figure 1).
Connect the other end of the cable to the Ethernet port on the router (or another
LAN device).

SMARTZONE G5 USER MANUAL
7
Figure 1: Ethernet Port for Network Connection
Connecting the PDU to a Computer Serial Port
If unable to connect to network, you can change the network setting using the serial
interface.
To configure the network setting, perform the following steps:
1. Serial connect the PDU to a computer’s serial port. Set baud rate for a terminal
emulation program.
2. Using a CLI command to enable DHCP or set a static IP.
3. Verify access to the Web interface. The Ethernet LED on the PDU front panel
provides communication status by color and display activity. The recessed Reset
button restarts the PDU (see Figure 2 below).

SMARTZONE G5 USER MANUAL
8
Figure 2: Locate Reset Button
Setup Serial Communication
You may configure the network settings using the command line interface (CLI) with a
serial connection. Users can connect serially using the optional RJ45-DB9 cable
Panduit p/n: MA001 (or make your own cable by creating a unique pinout as described
below in the “Serial Cable Pinout to Create Your Own Cable” in Section 4).
1. Verify that the computer has a serial port. If your computer does not have a DB9
serial connector, but does have a USB connector, obtain a USB-to-DB9 Adapter to
convert the USB to a DB9 serial port.
2. Using the optional RJ45-DB9 cable (Panduit p/n: MA001), connect the RJ-45 end to
the port labeled “Serial+RS485-1” on the front panel of your PDU model (see Figure
1). Connect the DB9 end of the cable to the computer.
3. Open the terminal emulation program (HyperTerminal or PuTTY) on the computer
and select the serial port connection (such as COM1).
4. Set the communications port as follows:
•Bits per second: 115200
•Data bits: 8

SMARTZONE G5 USER MANUAL
9
•Parity: None
•Stop bits: 1
•Flow control: None
(See Port Settings example below)
Figure 3: Port Setup Settings
5. Use the default initial login indicated below. Note that the username and password
are both case sensitive:
•Username: admin
•Password: 12345678 (or your new password)
6. The “Panduit>” prompt appears after you have logged in, ready to enter the CLI
command.
7. To configure network settings, enter the appropriate “net” command and press
Enter. All commands are case sensitive. You can type ?to access the commands.
8. To enable the IPv4 DHCP by default, run:
•net tcpip dhcp

SMARTZONE G5 USER MANUAL
10
•Enter Y to confirm and the PDU’s Intelligent Network Controller will reboot.
9. To set a static IPv4 configuration, run:
•net tcpip static x.x.x.x (ipaddress) x.x.x.x (netmask) x.x.x.x (gateway)
•Example: net tcpip static 192.168.1.100 255.255.255.0 192.168.1.1
•Enter Y to confirm and the PDU’s Intelligent Network Controller will reboot.

SMARTZONE G5 USER MANUAL
11
Section 2 – Web Graphical User Interface (GUI)
Configuration
Internet Protocol (IP) Address
The PDU is by default configured Dynamic Host Configuration Protocol (DHCP). The
PDU automatically obtains an IP address via a DHCP server when connected to a
network. The IP address the PDU received is displayed on the OLED screen. After the
PDU received the address, login to the Web interface to configure the PDU and assign
a static IP address (if desired). If there is no DHCP server, the default IP address is
192.168.0.1, which will be displayed on the PDU.
If the network does not use a DHCP server, see the CONNECTING THROUGH A
SERIAL CONNECTION section to configure a static IP address.
1. Connect a standard Ethernet patch cable to the Ethernet port on the PDU.
2. Connect the other end of the Ethernet cable to the LAN.
3. Make sure the Ethernet port on the PDU shows a solid green light on the left and a
flashing yellow light on the right to indicate successful connectivity to the network.
4. Use the menu buttons to look up the IP address of the device on the OLED display
by selecting Setup > Network > IPv4 or IPv6 as applicable.
5. In a standard web browser, enter the PDU IP address and proceed to configure the
PDU as shown in the Web Configuration section.
Web Configuration
Supported Web Browsers
The supported Web browsers are Mozilla Firefox, Microsoft Internet Explorer Version
11, Microsoft Edge, and Google Chrome mobile and desktop, Apple Safari mobile and
desktop.
Logging in to the Web Interface
Logging In
•Open a supported web browser and enter the IP address of the PDU.
oIf username and password were configured during the Network Configuration
Setup: enter the username and password in the appropriate fields. Press
Login or Enter.

SMARTZONE G5 USER MANUAL
12
oIf username and password were NOT configured during the Network
Configuration Setup, use the default username: admin and password:
12345678. For security purposes, change the password upon login.
Introduction to the Web GUI
Login Page
Figure 4: Login Page

SMARTZONE G5 USER MANUAL
13
Landing Page/Dashboard
Figure 5: Landing Page/Dashboard
Number
Icon
Description
1
The home icon provides an
overview of the PDU with
access to the Dashboard,
Identification, and Control
& Manage.
2
The Alarm icon provides
details of the active critical
alarms and active warning
alarms.
3
This icon lets you select a
Language. There are
seven languages available
to choose from: English,
Chinese, French, Italian,
German, Spanish, Korean
and Japanese.
4
This icon provides the logs
of the PDU which can be
viewed and downloaded.

SMARTZONE G5 USER MANUAL
14
Number
Icon
Description
•The Data Log is a
log of the Power,
Environmental, and
Security values.
5
The settings icon allows a
user to setup the Network
Settings, System
Management, SNMP
Manager, Email Setup,
Event Notifications, Trap
Receiver, Thresholds, and
Rack Access Control.
6
The search icon allows you
to input key words and
search for the related
results.
7
Information about the PDU
can be found using this
icon. You also can also
click user guide and
license to ask for help.
8
This icon shows who is
logged in (user or admin).
Account passwords can be
changed, and user
accounts managed
through this page.

SMARTZONE G5 USER MANUAL
15
Menu Dropdowns
Overview
Alarms
Help
Language
Logs
Settings
Admin

SMARTZONE G5 USER MANUAL
16
Introduction to the Dashboard
Power Summary Page
Figure 6: Power Summary Page
Outlet Monitoring Page
Figure 7: Outlet Monitoring Page

SMARTZONE G5 USER MANUAL
17
Environmental Page
Figure 8: Environmental Page
Security Page
Figure 9: Security Page

SMARTZONE G5 USER MANUAL
18
Section 3 – Simple Network Management
Protocol (SNMP)
SNMP Management Configuration
Setup SNMP
1. Access the Web interface and login.
2. Under SNMP Managers, select SNMP General (or type SNMP in the search).
The SNMP General page displays.
Figure 10: SNMP Management
3. The SNMP General includes SNMP Access and Version.

SMARTZONE G5 USER MANUAL
19
Figure 11: SNMP General
Setup SNMP Port
1. Access the Web interface and login.
2. Under SNMP Managers, select SNMP Port. The SNMP Port page displays.