Panduit Atlona OmniStream Series User manual

Atlona Manuals
Networked AV
AT-OMNI-232
AT-OMNI-238
AT-OMNI-121
AT-OMNI-122
AT-OMNI-512
AT-OMNI-521
AT-OMNI-111
AT-OMNI-112
Certied Switches

OmniStream Certied Switches 2
Version Release Date Notes
1Aug 2017 Initial release
2Aug 2017 Added Luxul XMS 7048P switch
3Aug 2017 Added static route information
4 Nov 2017 Added Luxul AMS 4424P switch
5Jun 2018 Added Pakedge S3L-24P
6Jul 2018 Added Cisco SG350 and SG550X switches
7 Aug 2018 Added Luminex GigaCore 26i
8 Sep 2018 Added Ruckus ICX 7150-48ZP
9Nov 2018 Added IGMP and PoE budget requirements for switches used with OmniStream
10 Dec 2018 Added Ubiquiti ES-48-500W / 750W switch
11 Mar 2019 Luxul switches removed - not OmniStream certified; added Cisco SG350X-24MP
12 May 2019 Added Araknis Networks AN-310-SW-F/R-16-POE and F/R-24-POE
13 May 2019 Added Araknis Networks AN-310-SW-F/R-8-POE
14 Jun 2019 Added step-by-step instructions for manually configuring certified Cisco and
Araknis switches.
15 Jun 2019 Added Appendix/troubleshooting section
16 Jun 2019 Added Ubiquiti ES-24-500W / 250W switch
17 Jul 2019 Added Netgear M4300-28G-PoE+ / M4300-52G-PoE+ switches
18 Sep 2019 Added Cisco SG350X-48MP switch
19 Sep 2019 Added Extreme Networks X460-G2-24P-10GE4
20 Sep 2019 Added Aruba Networks 2930F-24G-PoE+-4SFP
Version Information

OmniStream Certied Switches 3
Introduction 4
Switch Requirements 4
IGMP 4
PoE Budget 4
Features of Congurations 5
Known Limitations 5
Home Router Static Routing 6
Default Congurations 7
Araknis Networks AN-310-SW-F/R-8-POE 7
Araknis Networks AN-310-SW-F/R-16-POE 8
Araknis Networks AN-310-SW-F/R-24-POE 9
Aruba Networks 2930F-24G-PoE+-4SFP 12
Cisco SG300-10MPP 16
Cisco SG300-28MP 17
Cisco SG300-52MP 18
Cisco SG350-10MP 20
Cisco SG350-28MP 21
Cisco SG350-52MP 22
Cisco SG350X-24MP 23
Cisco SG350X-48MP 24
Cisco SG550X-24MP 25
Cisco SG550X-48MP 26
Extreme Networks X460-G2-24P-10GE4 27
Luminex GigaCore 26i 28
Netgear M4300-28G-PoE+ 31
Netgear M4300-52G-PoE+ 32
Pakedge S3L-24P 36
Ruckus ICX 7150-48ZP 38
Ubiquiti ES-24-500W / ES-24-250W 41
Ubiquiti ES-48-500W / ES-48-750W 42
Network Switch Conguration 47
Araknis AN-310-SW-24-POE 47
Cisco SG350X-24MP 50
Getting Started 50
VLAN Setup 52
IPv4 Interface Setup 55
Conguring IP Multicast 59
Creating User Accounts 65
Appendix 67
Troubleshooting 67
Table of Contents

OmniStream Certied Switches 4
Introduction
Switch Requirements
Atlona has made every eort to make sure that all switches listed in this document, meet or exceed functionality
with OmniStream products, identifying them as OmniStream Certied Switches. Atlona will continue to update this
document as more switches are tested. However, due to the vast number of manufacturers and switch models
on the market today, it is not possible to test each one. Before purchasing a switch that is not included in this
document, make sure that it supports the following features.
IGMP
• IGMP Snooping
• IGMP Querier
• IGMP Immediate Leave
• Unregistered Multicast Flooding
• Static Multicast Groups (optional)
PoE Budget
In addition to the above requirements, the power budget of the PoE switch must be identied. To determine the
maximum number of PoE devices that can be connected to a switch, two factors need to be considered:
1) The PoE budget of the switch.
2) The power requirements of each device.
When purchasing a switch, identify the PoE budget or power dedicated to PoE, in the switch specications.
This number is the total power that the switch can provide when PoE devices are connected. For example, a 24-port
370-watt PoE switch can supply up to 15.4 W of power on all 24 ports. In this case, you can connect 24 OmniStream
units.
IMPORTANT: Failing to meet all of the above requirements (except for Static Multicast Groups) may
lead to performance issues.
NOTE: If connecting OmniStream devices to a non-PoE switch or if using the analog audio
capabilities, then OmniStream units must be connected to the external power supply (Atlona part no.
AT-PS-48083-C). The power supply is not included and sold separately.

OmniStream Certied Switches 5
Switch
Home Router
Encoder
Decoder
Decoder
Encoder
AMS VM
1 2
ID
PWR LINK
TM
O
MNI
S
TREAM
1 2
ID
PWR LINK
TM
O
MNI
S
TREAM
HDMI
PWR LINK
TM
O
MNI
S
TREAM
VOLUME
DISPLAY
INPUT
ID
1 2 1 2
HDMI
PWR LINK
TM
O
MNI
S
TREAM
VOLUME
DISPLAY
INPUT
ID
1 2 1 2
Legend
VLAN 10
VLAN 1
Features of Congurations
• Connect OmniStream devices plug and play.
• Connect management ports to an external network, such as a home router.
NOTE: Devices that are connected to either OmniStream ports (VLAN 10) or management ports
(VLAN 1) on the OmniStream switch will be able to communicate with both the OmniStream units as
well as the Internet (using a connected home router). Devices that are connected to the home router
will only be able to connect to OmniStream devices if a static route is congured on the home router.
Refer to Home Router Static Routing (page 6) on the next page.
Known Limitations
• The network conguration le is applicable only to one standalone switch.
• If planning to connect multiple switches together, then a custom conguration will be required.
• Management network must use IP addresses from 192.168.1.1 through 192.168.1.253. If a dierent range is
used, then a custom conguration will be needed.
• The management ports have DHCP disabled, as a typical home router will handle this task. If the system will not
be connected to another network using the management ports, one of the OmniStream ports should be used for
management.
• Without a static route congured on the home router, any devices connected to the home router will not be able
to connect to the OmniStream devices.
• The home router must be set to 192.168.1.x in order for the Internet to be accessible from the OmniStream VLAN
(VLAN 10).
Introduction

OmniStream Certied Switches 6
Introduction
Home Router Static Routing
In order for devices that are connected to the home router, to be able to connect to OmniStream devices on VLAN
10, a static route must be congured on the home router. This static route is required to send the network trac to
the proper destination. Conguring static routing will vary by manufacturer, but most home routers have this ability.
Essentially, the router must be instructed to route any trac bound for the 10.1.0.0/23 range (also referred to as the
range starting with 10.1.0.0 with a subnet mask of 255.255.254.0) will use the gateway 192.168.1.254. However, if
the home router is using the same gateway, then the IP address of the switch must be changed to 192.168.1.253.
A static route for the OmniStream ports (VLAN 10) has been dened assuming that the home router is set to
192.168.1.1. If this is not the case, then the static route will need to be modied to enable Internet access to the
OmniStream VLAN.
NOTE: Without dening a static route on the home router, the system will still function properly but
without connectivity to the OmniStream devices (VLAN 10) from the home router.
NOTE: If the home router is not set to 192.168.1.1, then the conguration le may still be used as is,
but VLAN 10 will not have Internet access.

OmniStream Certied Switches 7
Araknis Networks AN-310-SW-F/R-8-POE
Summary
Version: 1.2.00
Ports 1 through 8 can be used to connect OmniStream devices.
Conguration Details
• Spanning tree mode: RSTP
• IGMP
* Snooping: Enabled
* Immediate leave: Enabled
* Querier: Enabled
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 10
* Default gateway: 10.1.1.1
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
physical port on the switch.
Conguration File https://atlonainc.box.com/s/y81xwh9cev5m4fn94589gjvphu18bqu5
Default Congurations

OmniStream Certied Switches 8
Araknis Networks AN-310-SW-F/R-16-POE
Default Congurations
Conguration File https://atlonainc.app.box.com/s/s4rhypkqyjacbmqh3tczl7auxz7q8mpm
Summary
Version: 1.2.00
Ports 1 through 16 can be used to connect OmniStream devices.
Conguration Details
• Spanning tree mode: RSTP
• IGMP
* Snooping: Enabled
* Immediate leave: Enabled
* Querier: Enabled
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 18
* Default gateway: 10.1.1.1
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
physical port on the switch.

OmniStream Certied Switches 9
Araknis Networks AN-310-SW-F/R-24-POE
Conguration File https://atlonainc.app.box.com/s/vrerlra60k0z868irqf2bliqn42nf6n8
Summary
Version: 1.2.00
Ports 1 through 24 can be used to connect OmniStream devices.
Conguration Details
NOTE: Araknis L2 switches do not provide an integrated DHCP service. A separate DHCP server
will need to be provided. In this case, a router with DHCP pool enabled can be connected to any
physical port on the switch.
• Spanning tree mode: RSTP
• IGMP
* Snooping: Enabled
* Immediate leave: Enabled
* Querier: Enabled
• Hostname: DemoSw
• Login credentials
* Username: admin
* Password: Atlona
• VLAN 1
* Ports: 1 through 26
* Default gateway: 10.1.1.1
Once the conguration le has been uploaded, access the switch GUI using the following IP address:
VLAN1: http://10.1.1.254
Default Congurations

OmniStream Certied Switches 10
Instructions for uploading the conguration le for Araknis switches
1. Download the required conguration le.
2. Open a web browser and enter the IP address of the switch in the address bar: 192.168.20.254
3. Enter the login credentials to access the user interface. The default credentials are listed below:
Username: araknis
Password: araknis
4. Click MAINTENANCE > FILE MANAGEMENT.
Default Congurations
5. Under the Conguration File section, click the Choose File button and select the conguration le which was
downloaded in Step 1.
Choose File button