NOTE:
NOTE:
IF THE REAR SHROUDIS ASSEMBLEDTO THE PARABODY425, IT WILL NEED "]70 BE REMOVEDTO
ASSEMBLE THE LEG PRESS AND THE ADAPTER KIT. PLEASE REMOVETHE SE[ROUD AT THIS TIME
BY REMOVINGTHE FOUR(4) 3/8 X 1 IN. BOLTS ANDFOUR3/8 IN. WASHERS.
THE LEG PRESS ATTACHMENT(832101) MUST BE ASSEMBLED BEFORE ASSEMBLING IT TO THE
PAKABODY425. PLEASE ASSEMBLE THE LEG PRESS ATTACttMENT AT TIIIS TfME USING THE 832
PRODUCT ASSEMBLY INSTRUCTIONS.
1. Attach O, vo (2) 2 SQ. IN. COVERCAPSonto the FRONTLEGWELDMENTas shown on drawing.
Removetwo (2) I/2 FN’. LOCKNUTSand two (2) 1/2 IN. WASHERSFROMthe PRESSBASE:\ 13ASEconnection of the
425.
SECURELYassemble the BASECONNECTIONWELDMENTto the PRESSIIASE and BASF, connection of the -12S
using the two (2) I12 IN. LOCKNUTSREMOVEDIN STEP
oSECURELYattach the assembled 832 LEGPRESS ATTACHMENTto the FRONTLEG ~rELDMENTusing two (2)
I/2 X3 IN. BOLTS,two (2) I/2 IN. WASHERS(~To, OMS’[’EP2) and two (2) I/2 IN. LOCKNUTS.
SECURELYattach the 832 to the 425 by connecting the FRONTLEGWELDMENTto the BASECONNECTION
WELDMENT,using two (2) I/2 X 3. IN. BOLTS,two (2) 112 IN. WASHERSand two (2) I/2 IN. I_,OCK
Removeone (I) 1/4 .IN. CAPNUTfrom the rear L-hook of the TOPBOOM.(LEAVE2 IN. PULLEYONL-HOOK)
Assembleone (I) 2 IN. PULLEYto the rear L-hookand secure place ~vith one (I) 114 IN. CAP
CAREFULLYremove one (I) 318 IN. LOCK~ and one (I) SWIVELWITHMULTI-PRESSSHOCKCORDfrom
rear fiat of the BASE.
o
I0.
Removeone 3/8 IN. NUT,one (I) 2-3/8 IN. CABLERETAININGCLIP, one (1) 3-I/2 X1 IN. PULLEY,one (1) Y/8
1/2 IN BOLT,and one (1) 3/8 IN. WASHERfrom the rear flat ofthe BASE.
Reassemble one (I) 3-112 x I IN. PULLEY,one (I) 2-318 IN. CABLERETAININGCLIP, one 318 WASI-IF_R,and one
(I) 318 IN. NUT,from Step 9 to the rear fiat of the BASEusing one (I) 318 x 4-I/2 IN. THREADEDSTUD,and one (1)
318 IN. NLIT.
11.
12.
Reassemble one (1) SWIVELWITHMULTI-PRESSSHOCKCORDto the 3/8 X 4-1/2 IN. TI-tl~AI)ED STUD,using
(I) 318 IN. LOCKNq.JT. (PARTS ARE FROMSTEP 8)
Assembleone (1) 3-1/2 x I IN. PULLEYto the flat facing the leg press on the BASE,and one (1) 3-1/2 IN. PULLEYto the
fiat on the FRONTLEGWELDM’ENTusing two (2) 3/8 x 2 iN. BOLTS,two (2) 3/8 IN. WASHEt~,two {2) 2-3/8
CABLERETAININGCLIPS, and taro (2) 3/8 IN. LOCKNUTS.
13. To assemble the LEGPRESSCABLE,follow lhe cable muting diagram and use the following steps:
Adjustthe LEGPRESSso the seat is in its tightest pre-stretch position.
SECURELYattach the loop end of the LEGPRESSCABLEto the FROIqr LEGWELDMENTusing one (I)
QUICK DISCONNECTLINg<.
~un the cable through the hole in the D-RINGas showain (’DETAILA) and attach one {’I) KEYHOLECLEVIS
to the end of the LEGPRESSCABLE.
12F21/95
