ParaBody 965101 User manual

SeriousSteel
965101
FLAT & INCLINE BENCH
.ASSEMBLY INSTRUCTIONS
ParaBody, Incorporated
14150 Sunfish Lake Boulevard
Ramsey, MN55303
1-800-328-9714
Part# 6653501 Revision:11/26/96

965101 FLAT & INCLINE BENCH ASSEMBLY PARTS LIST
SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBI,Y
HARDWARE."
ITEM NAME/DESCRIPTION Q’IT
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
1/2X9-I/2I"NBOLT......................................................................................................... 1
1/2X6-1/21l"i’4BOLT......................................................................................................... 1
1/2X3INBOLT............................................................................................................... 2
1/2X1-1/4INBOLT......................................................................................................... 2
3/8X1INBOLT............................................................................................................... 6
1/2INW~SHER................................................................................................................. 6
3/8INWASHER................................................................................................................. 6
1/2INLOCKNUT............................................................................................................. 3
1/2INLOWHEIGHTLOCKNUT.................................................................................... 3
HINGETAB...................................................................................................................... 2
6-1/8X3-7/8INU-PIN...................................................................................................... 1
1/2113X5/gINSPACER.................................................................................................... 1
SPRINGPINASSEMBLY................................................................................................. 1
1/2INIDCAPNUT............................................................................................................ 1
3X2ININSERTGUIDE.................................................................................................. 2
3X2INEI’IDCAP............................................................................................................ 3
7/16IDX4INVINYLCAP.............................................................................................. 1
WELDMENTS/PARTS:
ITEM NAME/DESCRIPTION QTY
2.
3.
4.
5.
6.
7.
8.
REARUPRIGHTWELDMENT............................... (6651703)..................................... 1
BENCHFRAMEWELDMENT................................ (6652103)..................................... 1
ADJSLEEVEWELDM]gNT..................................... (6~;52803)................... : ................. 1
BACKPADANGLE’WELDMENTLEFT............... (6624202)..................................... 1
BACKPAD ANGLEWELDMENTRIGHT............ (6624302)..................................... 1
1/2X2 X15-1/2INPLATE....................................... (6(,51602)..................................... 2
SEATPAD.................................... .~..~..~.:.~....~....X..~....(~..................................... 1
BACKPAD............................................................... (66529XX).....................................
NOTE: BOLT LENGTHIS MEASUREDFROMTHE UNDERSIDE OF THE HEADOF THE ~3OLT.
BOLT LENGTH,
BOLT LENGTHRUL]gR:
1/2 I 1/2 [ 1/2 I 1/2 , [ 1/2 [ I/2
34 5 6
Part # 6653501 2 Revision: 11/26/96

965101 FLAT & INCLINE BENCHASSEMBLYINSTRUCTIONS
1. Slide one (1) 7/]L6 ~ X 4 ~ ~ C~ onto ~e 6-1/8 X 3-7/8 ~ U-P~ ~d proceed to am;emble it
~e BENC~ FR~ ~LD~NT ~ sho~ on ~w~g.
Insert two (2) 3 X 2 INSERTGUIDESinto each end of the ADJSLEEVEWELDMENTas .,;hoxvn
drawing. (NOTE: MAKESURE THE INSERT GUIDES S NAP INTO THE HOLES OF THE
WELDMENT)..SECURELYassemble the SPRING PIN ASSEMBLYto the ADJ SLEEVE
WELDMENTas shown in (DETAIL A).
Pull back the SPR.INGPIN on the ADJSLEEVEWELDMENTand slide it over the end of ~ae BENCH
FRAMEWELDMENT,as shown on drawing. Slide WELDMENTup to the f’ast adjustmenl ~. hole
underneath.
oInsert three (3)’3 X2 IN ENDCAPSinto the ends of the REARUPRIGHTWELDMENTa:; shown
drawing.
SECURELYa.~;semble the REAR UPRIGHTWELDMENTto the BENCHFRAMEWELDMENTas
shownon drawing.
Assemble the LEFT and RIGHTBACKPAD ANGLEWELDMENTS,along with two (2) HINGE
TABS to the BENCHFRAMEWELDMENTas shown on drawing. (NOTE: TIGHTEN
CONNECTION ENOUGHTO REMOVE TIlE PLAY YET ALLOWING THE PARTS TO
ROTATE FREELY).
7° Assemble t~vo (2) 1/2 X 2 X 15-1/2 IN PLATESto the inside of the LEFTand RIGHTBACKPAD
ANGLEWEL’I)MENTS as shown on drawing. (’NOTE: TIGHTEN CONNECTIONENOUGH
REMOVE"lille PLAY ~rET ALLOWINGTHE PARTS TO ROTATEFREELY).
Rotate the LEFT and RIGHTBACKPADANGLEWELDMENTSup and assemble the 1/2 X 2 X 15-
1/2 IN PLATESto the ADJ SLEEVEWELDMENTas shown on drawing. (NOTE: DONOTOVER
TIGHTEN TI]~S CONNECTION).
Part # 6653501 3Revision: 11/26/96

965101 FLAT & INCLINE BENCH ASSEMBLY INSTRUCTIONS
10.
SECURELYassemble the BACKPAD to the LEFT and RIGHT BACKPAD ANGLE
WELDMENTSas shown on drawing.
SECURELYassemble the SEAT PAD to the HINGETABS on the BENCHFRAMEWELDMENTas
shown on drawing.
Part# 6653501 4 Revision: 11/26/96

Z
0
Z
Z
z
\\
/ \
z
z ~.
I-
z
\\
\
\ \\
\\\\
/
/
/
/
/
/
/
\\

965101
SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY
HARDWARE:
ITEM NAME/DESCRIPTION Q’I’T
I. 1/2x9-1/2INBOLT..........................................................................................................
2. 1/2 X5-1/2 IN BOLT
3. 1/2 X 3 IN BOLT
4. 1/2X1-I/4 BOL................. ~..........................................................................................
2
5. 3/8 X 1 IN BOLT
6. 1/2INWA.SHER.................................................................................................... 6
7. 3/,INWASI-mg............................................. "............
6
8. 1/2INLOC~:~........................................
9. 1/2INLOWr~.~LOCr~:r................ :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
10. HINGE TAB . .
12. 1/2 ID X5/8 IN SPACER
13. SPRING PIN ASSEMBLY
14. 1/2INIDCAPNUT.................................... 1
15. 3x2ININSEV.TGtr~E.......,....................
::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::
16. 3X2IN..1..E~II~,.CAP............................... 3
17. 7/16IDX4 INVINYLCAP..................
FLAT & INCLINE BENCHASSEMBLYPARTS LIST
mllllllml~lmlll
WELDMENTS/PARTS:
ITEM
2.
3.
4.
5.
6.
7.
8.
NAME/DESCRIPTION
REARUPRIGHTWELDMENT............................... (6651703)..................................... 1
BENCHFRAMEWELDMENT................................ (6652103)..................................... 1
ADJSLEEVEWELDMENT..................................... (6652803)............ :......
i.................1
BACKPADANGLEWELDMENTLEFT............... (6624202)..................................... 1
BACKPADANGLEWELDMENTRIGHT............ (6624302)..................................... 1
1/2X2X15-1/2INPLATE....................................... (6651602)..................................... 2
SEATPAD................................................................ (66535XX)..................................... 1
BACKPAD............................................................... (66529XX)..................................... 1
NOTE:BOLTLENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
iiii/i!!1
BOLTLENGTH [
BOLT LENGTHRULER:
112 [
01112 [ 1/2 [ 1/2 [ 1/2 [ 112
I 2 3 t 4 56
P,’u’t #6653501 Revision:11/26/96

965101 FLAT & INCLINE BENCHASSEMBLYINSTRUCTIONS
1.
o
o
Slide one (1) 7/16 ID X4 IN VINYLCAPonto the 6-1/8 X 3-7/8 IN U-PINand proceed to assembleit to"
the BENCHFRAMEWELDMENTas shown on drawing.
Insert two (2) 3 X 2 INSEP~TGUIDESinto each end of the ADJSLEEVEWELDMENTas shown
drawing. (NOTE: MAKESURE THE INSERT GUIDES SNAP INTO THE HOLES OF THE
WELDMENT).SECURELYassemble the SPRING PIN ASSEMBLYto the ADJ SLEEVE
WELDMENTas shown in (DETAIL A).
Pull back the SPRINGPIN on the ADJSLEEVEWELDMENTand slide it over the end of the BENCH
FRAMEWELDMENT~ shown on drawing. Slide WELDMENTup to the flu-st adjustment hole
underneath.
Insert three (3) 3 X 2 IN ENDCAPSinto the ends of the REARUPRIGHTWELDMENTas shown
drawing.
SECURELYassemble ~e REAR UPRIGHT WELDMENTto the BENCHFRAMEWELDMENTas
shownon drawing.
Assemble the LEFT and .RIGHT BACKPADANGLEWELDMENTS,along with two (2) H1NGE
TABSto the BENCHFtL~ME WELDMENTas shown on drawing. (NOTE: TIGHTEN
CONNECTION ENOUGH TO REMOVE THE PLAY YET ALLOWING THE PARTS TO
ROTATE FREELY).
Assemble two (2) 1/2 X 2 X 15-1/2 IN PLATESto the inside of the LEFTand RIGHTBACKPAD
ANGLEWELDMENTSas shown on drawing. (NOTE: TI(;HTEN CONNECTIONENOUGH
REMOVETHE PLAY ~’ET ALLOWINGTHE PARTS TC, ROTATE FREELY).
Rotate the LEFT and RIGHTBACKPADANGLEWELDMENTSup and assemble the 1/2 X 2 X 15-
1/2 IN PLATESto the ADJ SLEEVEWELDMENTas shown on drawing. (NOTE: DONOTOVER
TIGHTEN THIS CONNECTION).
Part # 6653501 Revision:1 ]/26/96

965101 FLAT & INCLINE BENCHASSEMBLYINSTRUCTIONS
9. SECURELYassemble the BACKPADto the LEFT and RIGHTBACKPADANGLE
WELDMENTSas shown on drawing.
SECURELYassemble the SEAT PAD to the HINGE TABSon the BENCHFRAMEWELDMENTas
shownondrawing.
10.
Part # 6653501 4Revision: 11/26/96

II
Z
X
l--
Z
,,.-,,y
X 0
x
/x /
~//
\
V
/
,/
/
/
/
/
/
\\
_z c
\\\\
Z