ParaBody 465104 User manual

I
Serious Steel
465104 GLUTE/SQUAT OPTION
I
ASSEMBLY INSTRUCTIONS
Part# 6872201 1 Revision:12/3/99

]IMPORTANT NOTES]
WELCOMETO THEWORLDOF ~e~iou$ $~eet]
I
Please note:
* Thankyoufor purchasing th~ Parabody465104Glute/Squat Option. Please read these
instructions thoroughlyand k~pthemfor fi~ture reference. This productmustbe assembled
ona fiat, level surfaceto assur~its properfunction.
* Werecommendclemfing your product (pads and flame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyourParabodycustomerservi~e representative
at [phone].
Thereis a risk assumedbyindividuals whouse this type of equipment.Tominimizerisk, please
followthese roles:
1. Inspect equipmentdaily. Tightenall loose connectionsandreplace wornpm~simmediately.
Failure to doso mayresult in seriousinjury.
2. Donot allow minorsor children to play on or arotmdthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuse of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
I Tools Required for Assembly~
*Rubbermallet or hanuner
* 3/4" wrench
*Ratchetwith 3/4" socket
* Adjustable wrench
* Tape measure
]Bolt LengthRuler
NOTE: BOLT LENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
BOLT LENGTH RULER:
BOLT LENGTH
I1/2 I1/2 [ 1/2 I 1/2 I1/2 [ 1/2 ]
2] I I I 1] I I I
0] I I II I

iKEY
1
2
3
4
PART# DESCRIPTION
6733802 FOOT PLATE
6736202 SQUAT BAR
6736502 GLUTE KICK
6016401 ROLLER PAD
PARTS
1
1
1
2
LIST
KEY PART #
5 6670701
,6 3102918
73102801
DESCRIPTION
NON-SKff ~IP
1/2 X3/4" BOLT
1/2" LOCKNUT
PRESS 1/2 X3-1/4"
BASE
FIGURE 1
STEP1
¯ Swingthe PRESSSEATover 90° to install FOOTPLATE(1). See FIGURE
¯ SECURELYattachthe FOOTPLATE(1) to the PRESSBASEusing two 1/2 X 3-1/4" BOLTS(6) and two 1/2" LOCKNUTS(7)
shownin FIGURE1.
1/2 I 1/2 ] 1/2 I 1/2 [ 1/2 ] 1/2 --I
6
2II I I
1[ I I 0[ I I
I3

PRESS
ARM
FIGURE 2
STEP2
¯Slide two ROLLERPADS(4) over the SQUATBAR(2). See FIGURE2. Space PADSout equally to support back of neck.
(Optional : SQUATBARmay be used without ROLLERPADS.)
¯ Insert SQUATBAR(4) into the hole on the PRESSARMas shown.
PRESS
ARM
FIGURE 3
ITEP3
¯ Insert other end of SQUATBAR(2) into the PRESSARM.See FIGURE
¯ Rotate SQUATBAR(2) ° tohol d SQUAT BAR(2) in P RESS ARM.See FIGURE 3.

PRESS
ARM
FIGURE4
~TEP4
¯ Attach one NON-SKIDSTRIP(5) to the GLUTEKICK(3) as shown in FIGURE
¯ Insert GLUTEKICK(3)into the hole on the PRESSARMas shown.
FIGURE5
STEP 5
¯ Rotate GLUTEKICK(3) ° to hold GLUTE KICK (3)in P RESS ARM.See FIGURE 5.
Thank you for purchasing the PARABODY465104 GLUTE/SQUATOPTION. If unsutre of proper use of
equipment refer to the 425104 OPERATIONGUIDE or call your local PARABODYdistributor or call the
PARABODYcustomer se~wice department at [phone].
5