ParaBody 912101 User manual

.~erious Steel
912101 ’WEIGHT CARRIAGE OPTION
ASSEMBLY INSTRUCTIONS
Part # 6678401 1Revision,: 02/24/97

IIMPORTANT NOTES]
There is a risk assumedby individuals whouse this type of equipment. To minimizerisk, please
follow these rules:
1. Consult your physician before beginning any exercise program.
2. Inspect equipmentdaily. Tighten all loose connections and replace wornparts immediately.
Failure to do so mayresult in serious injury.
3. Donot allow minors or children to play on or around this equipment.
4. Exercise with care to avoid injury.
5. If unsure of proper use of equipment,call your local Parabodydistributor or call the
Parabody customer service department at [phone].
Please note:
* Thankyou for purchasin~ the Parabody 912101Weight Carriage Option. Please read these
instructions thoroughly and keep themfor future reference. This product faust be assembled
on a flat, level surface to assure its properfunction.
* Werecommendcleanin~ your product (pads and frame) on a regular basis.., using warmsoapy
water. Touch-uppaint can be purchased from your Parabody customer ser~,ice representative
at [phone].
]Tools Required for Assembly]
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
Bolt LengthRuler
NOTE: BOLTLENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
IBOLT LENGTH ]
BOLT LENGTHRULER:
] 1/2 6
0 1

PARTS LIST
KEY
1
2
3
4
5
PART #DESCRIPTION
6675202 CARRIAGE
6675501 CHROME PLATE HOLDER
6675303 PLATE,1/4 X 3 X 12"
3102935 1/2 X 2.-3/4" BOLT
3102953 3/8. X4-.1/2" BOLT
QTY KEY
1 6
17
4 8
29
410
PART # DESCRIPTION
3102502 1/2" WASHER
3102804 1/2" LOWHEI LOCKNUT
3102802 3/8" LOCKNUT
6122704 1/4" SPACER
3108002 3/4" WEIGHTSTACKCUSHION
QTY
2
2
4
8
2
STEP1:
A. Securely attach the CHROMEPLATEHOLDER(2)
CARRIAGE(1) using two 1/2 X 2-3/4" BOLTS(4),
1/2" WASHERS(6), and two 1/2" LOWHEIGHTLOCK
NUTS(7) as showniin FIGURE
B. Attach two 3/4" WEIGHTSTACKCUSHIONS(10) to the
small robes on the bottom of CARRIAGE(1) as shown
FIGURE1.
STEP2:
TOWER
FIGURE 2 3/8 X4-1/2"1 ~.~
A. Place CARRIAGE(1) between TOWER.See FIGURE
B. Securely attach four 1/4 X 3 X 12" PLATES(3) to CARRIAGE(1) using four 3/8 X4-1/2" BOLTS
(5), eight 1/4" SPACERS(9), and four 3/8" LOCKNUTS(8) as shownin FIGURE
3

TOWER
BRACE
,TOP BOOM
FIGURE 3
STEP3:
Route threaded end of CABLE(part # 6671601) around pulleys in TOPBOOMand IPULLEYBLOCK
ASSEMBLY.Route CABLE(part # 6671601) down through hole in TOWERand TOWERBRACE
shown in FIGURE3.
STEP4:
Threadend of CABLE(part # 6671601)into
CARRIAGE(1) and securely tighten jam
nut as shownin FIGURE4.
FIGURE 4
1/2 1/2 2

FIGURE 5
STEP5:
A. Removethe BOLT&WASHERSbelow the PULLEYin upright. See FIGURE5,
B. Insert the threaded end of CABLE(part #6671001)under the PULLEYin UPRIGHTand around the
bottom PULLEYof the PULLEYBLOCK.See FIGURE5.
C. Fasten end of CABLE(part #6671001)into threaded housing on the base of BENCHFRAME.
D. Tighten jamnut securely. .
E. Securely fasten previously removedBOLT&WASHER.(NOTE:The CABLE(part #6671001) should
be routed over the bolt andwasher.
5

FIGURE 6
"~ LATBAR
," SNAPHOOK
RING
STEP6:
Attach CHROMELATBAR& DOUBLED CHROMEHANDLEto ball ends of cables using 5/16"
SNAPHOOKS.See FIGURE6.
THIS CONCLUDESTHE ASSEMBLYOF THE 912101