ParaBody 662101 Installation guide

1Part # 7046901
Rev B Revision: 07/31/01
ASSEMBLY INSTRUCTIONS
662101 GLUTE/SQUAT OPTION

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 662101 Glute/Squat Option. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* Rubber mallet or hammer
* 3/4” wrench
* Ratchet with 3/4” socket
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASUREDFROMTHEUNDERSIDEOFTHEHEAD OFTHEBOLT.
BOLT LENGTH RULER:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
WELCOMETOTHEWORLDOF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].

STEP 1
FIGURE 1
PART #
6748802
6748702
6740002
6016401
KEY
1
2
3
4
QTY
1
1
1
2
PART #
6670701
3102918
3102801
DESCRIPTION
NON-SKID STRIP
1/2 X 3-1/4” BOLT
1/2” LOCK NUT
QTY
1
2
2
DESCRIPTION
FOOTPLATE
SQUATBAR
GLUTE KICK
ROLLER PAD
KEY
5
6
7
PARTS LIST
• Swing the PRESS SEAT over 90° to install FOOT PLATE (1). See FIGURE 1.
3
7
1
6 1/2 X 3-1/4”
PRESS
BASE
• SECURELY attach the FOOT PLATE (1) to the PRESS BASE using two 1/2 X 3-1/4” BOLTS (6) and two 1/2” LOCK NUTS (7) as
shown in FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2

STEP 3
FIGURE 2
• Insert other end of SQUAT BAR (2) into the PRESS ARM. See FIGURE 3.
4
• Rotate SQUAT BAR (2) 90° to hold SQUAT BAR (2) in PRESS ARM. See FIGURE 3.
FIGURE 3
2
4
STEP 2
• Slide two ROLLER PADS (4) over the SQUAT BAR (2). See FIGURE 2. Space PADS out equally to support back of neck.
(Optional : SQUAT BAR may be used without ROLLER PADS.)
• Insert SQUAT BAR (4) into the hole on the PRESS ARM as shown.
PRESS
ARM
PRESS
ARM
2

5
STEP 5
FIGURE 4
• Rotate GLUTE KICK (3) 90° to hold GLUTE KICK (3) in PRESS ARM. See FIGURE 5.
FIGURE 5
5
3
STEP 4
• Attach one NON-SKID STRIP (5) to the GLUTE KICK (3) as shown in FIGURE 4.
• Insert GLUTE KICK(3) into the hole on the PRESS ARM as shown.
PRESS
ARM
PRESS
ARM
3
ThankyouforpurchasingthePARABODY662101 GLUTE/SQUATOPTION. If unsure of properuse of
equipmentreferto the662101OPERATION GUIDE orcall yourlocalPARABODYdistributor orcallthe
PARABODYcustomerservice department at [phone].