ParaBody 216 User manual

1
216 50 LB. ADD-ON KIT
ASSEMBLY INSTRUCTIONS
WARNING:
Read and follow all directions
for each step to insure proper
asembly of this product.
CLASSH
PART # 7016801
REV. B Revision: 03/23/01
Version: 216101

PARTS LIST
PART #
6939201
7095801
KEY
1
2
QTY
5
1
KEY
3
4
PART #
6978101
6382301
DESCRIPTION
WEIGHTSTACKLABEL
WEIGHTPLATE BUSHINGS(10CT)
QTY
1
1
DESCRIPTION
WEIGHTPLATE
WEIGHTSTACK SHAFT
FIGURE 1
• Insert two WEIGHT PLATE BUSHINGS (4) into each of the five WEIGHT PLATES (1) as shown in FIGURE 1.
STEP 1:
4
1
2

3
FIGURE 2
• Unscrew the WEIGHT STACK CABLE
from the 15 HOLE WEIGHT STACK
SHAFT as shown in FIGURE 2.
STEP 2:
WEIGHT
STACK PIN
WEIGHTSTACK
CABLE
15 HOLE WEIGHT
STACK SHAFT
• Remove the WEIGHT STACK PIN from
the 15 HOLE WEIGHTSTACK SHAFT as
shown.
• CAREFULLY remove or loosen bolts in the TOP BOOM
to allow the GUIDE RODS to be tilted. Refer to the GYM
ASSEMBLYINSTRUCTIONS.
FIGURE 3
STEP 3:
• Tilt the GUIDE RODS back and remove the SHAFT
COLLARS, HEAD PLATEASSEMBLY, fifteen WEIGHT
PLATES, twoWEIGHT STACK CUSHIONS, two 3/4”
WASHERS, and two WEIGHT STACK SPACERS as shown
in FIGURE 3. (NOTE: Please discard the two 3/4”
WASHERS, and the two WEIGHT STACK SPACERS.)
HEADPLATE
SHAFTCOLLAR
WEIGHTSTACKSHAFT
BASE
WEIGHTPLATE
WEIGHTSTACK CUSHION
3/4” WASHER
WEIGHTSTACK
SPACER
GUIDE ROD

4
• Remove the E-RING and the old WEIGHT STACK SHAFT from
the HEAD PLATE. (NOTE: Please discard the old WEIGHT
STACKSHAFT.)
FIGURE 4
STEP 4:
• Slide the new 20 HOLE WEIGHT STACK SHAFT (2) thru
the hole in the HEAD PLATE and lock in place using the
previously removed E-RING as shown in FIGURE 4.
2
STEP5:
HEADPLATE
• Insert the two GUIDE RODS through the two WEIGHT
STACK CUSHIONS into the base as shown in FIGURE
5. Lubricate the GUIDE RODS with a silicon or
teflon spray that is available at most hardware
stores.
• USING EXTREME CARE, slide the five new WEIGHT
PLATES (1) and the previous fifteen WEIGHT PLATES
down over the GUIDE RODS onto the WEIGHT STACK
CUSHIONS. (NOTE:Makesurethatthe key holes of the
WEIGHTPLATESallfacethesameway.)
• Carefully slide the new HEAD PLATEASSEMBLYand the
SHAFT COLLARS down over the GUIDE RODS onto the
weight stack as shown in FIGURE 5.
SHAFTCOLLAR
WEIGHT
STACK
CUSHION
HEADPLATE
1
GUIDE ROD
BASE
FIGURE 5
E-RING

• TIGHTEN cable jam nut securely!
5
FIGURE 6
STEP 6:
WEIGHT
STACK PIN
WEIGHTSTACK
CABLE
20 HOLE WEIGHT
STACKSHAFT
• Assemble the WEIGHT STACK PIN to the
20 HOLE WEIGHTSTACK SHAFT as
shown.
• Screw the WEIGHT STACK CABLE into
the 20 HOLE WEIGHT STACK SHAFT of
the HEAD PLATE until the CABLE slightly
pulls on the HEAD PLATE.
Thank you for purchasing the Parabody 216101 50 LB. ADD-ON KIT. If unsure of proper use of equipment, call your local
LifeFitness distributor or call the Parabody customer service department at [phone].
• CAREFULLY assemble and SECURELY
tighten any previosly removed or loos-
ened bolts in the TOP BOOM to allow the
GUIDE RODS to be secured. Refer to the
GYMASSEMBLYINSTRUCTIONS.