ParaBody 415101 User manual

Serious Steel
415101 400 LEG PRESS ADAPTER KIT
ASSEMBLY INSTRUCTIONS
Part# 6694601
II Revision: 06/12/97

]IMPORTANT NOTES[
Thereis a risk assumedbyindividuals whouse this type of equipment.Tominimizerisk, please
followthese rules:
1. Consult yourphysician before beginningany exercise program.
2. Inspect equipmentdaily. Tightenall loose connectionsandreplace wornparts immediately.
Failure to doso mayresult in seriousinjury.
3. Donot allow minorsor children to play on or aroundthis equipment.
4. Exercisewithcare to avoidinjury.
5. If unsureof properuse of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
Please note:
* Thankyoufor purchasingthe Parabody415101LegPress AdapterKit. Please read these
instructions thoroughlyandkeepthemfbr future reference. Tl~:is productmustbe assembled
ona flat, level surfaceto assureits properfunction.
* Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyour Parabodycustomerservice representative
at [phone].
[Tools Required for Assembly]
* Rubbermallet or hammer
*3/4" wrench
* 9/16" wrench
* Ratchetwith 3/4" and 9/16" sockets
* 5/32" Allen wrench
* Adjustable wrench
* Tape measure
[ Bolt Length Ruler ]
NOTE: BOLT LENGTH IS MEASUREDFROMTHE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
BOLT LENGTH
5 6

3
4
5
6
7
8
9
PART #DESCRIPTION
6686603 FRONT LEG
6693902 PULLEY BRACKET
CABLE SWIVEL
6694002
6694203
3116201
6405201
6467001
3108102
6140701
BASE CONNECTION
3-1/2" PULLEY
2" SQ. ENDCAP
PARABODYLOGO END CAP
QUICK DISCONNECTLINK
GLIDE1 X 1"
PARTS LIST
QTY KEY PART #
1 10 3102501
1 11 3102802
1 12 3102801
113 3102924
214 3102904
1 15 3102918
216 6694301
117 6694401
2
DESCRIPTION
3/8" WASHER
3/8" LOCKNUT
1/2" LOCKNUT
3/8 X 1-3/4" BOLT
3/8 X 3" BOLT
1/2 X3-1/4" BOLT
112-3/4" CABLEASSY
82-1/2" CABLEASSY
NOTE:The LEGPRESSATTACHTMENT(832101) must be assembled before connecting it to the
PARABODY400 HOMEGYM
STEP1
¯Slide two PAILABODYLOGOENDCAPS(7) over
the FRONTLEG(1) as shown in FIGURE
QTY
4
5
2
3
2
2
1
1
FIGURE 2
STEP 3
¯ Attachtwo 1 X 1" GLIDES(9) tothetop of puLLEYBRACKET
(2) as shownin FIGURE
STEP2
¯ Slide one 2" SQ. ENDCAP(6) into the BASECONNECTION(4)
as shownin FIGURE2.
FIGURE 3

1/2X3’1/4"
FIGURE 4
STEP 4
¯ Securely fasten the FRONTLEG(1) and the BASECONNECTION(4) to the 400 HOMEGYMusing two 1/2 X 3-1/4" BOLTS
(15) and two 1/2" LOCKNUTS(12). See FIGURE
STEP 5
¯ ¯ Removeone existing 3-1/2" PULLEYand two SPACERS
fromthe ADJUSTMENTTUBEonthe 832 LEGPRESS
OPTIONby unfastening the 3/8 X 4-1/2" BOLTholding
the pulley on. See FIGURE5. (Note: Save 3-1/2"
PULLEY,it will be used in later steps.)
FIGURE 5
3-1/2"
~PACER
BOLT
I1/2 I1/2 I 1/2 i1/2 I
3I4
I I i
I I I
4
I5

STEP 6
¯Attach CABLE SWIVEL (3) to the
ADJUSTMENTTUBEon the 832 using the
existing previously removed3/8 X4-1/2"
BOLTS, WASHERS, 2" WHEELS AND
NUT.(Note: Securelytighten, then backoff
1/4 turn to allow the CABLESWIVEL&
WHEELSto rotate freely.) See FIGURE6.
FIGURE 6
FIGURE
3/8 X3"
STEP 7
¯Securely fastenthe 832 LEGPRESSto the FRONTLEG(i) using two 3/8 X 3" BOLTS(14), four 3/8" WASHERS(10), and
3/8" LOCKNUTS(11) as shown in FIGURE

FIGURE8
REMOVE
STEP 8
Removethe existing LATCABLE(part #668701)using the following steps:
¯ Discolmect LATBARfrom TOP BOOM.
¯ Unscrew the threaded end of CABLEfrom the HEADPLATEASSEMBLY.
¯ Route the LATCABLEaround the PULLEYBLOCKas shown in FIGURE8.
¯ Route the LATCABLEaround the TOPBOOMas shown in FIGURE8.
¯ The pulleys in TOPBOOMmayneed to be temporarily removedto remove CABLE.
[ 1/2 [ 1/2 I 1/2 I 1/2 [
0 1 2 3 4 1/2 [ 1/2 I
56

FIGURE 9 Cablemustrunoverthetopofbolts.
Loop CABLE(16) around one 3-1/2" PULLEY(5) in the PULLEY
BRACKET(2) using on 3/8 X 1-3/4" BOLT(13) and 3/8"
LOCKNUT(11) as shown in FIGURE10.
STEP10
Screw the threaded end of CABLE(16) into the HEADPLATE
ASSEMBLY.
3/8 X1-3/4"
STEP 9
Install the NEW112-3/4" CABLEASSY(16) using the following steps:
¯ Route the CABLE(16) through the TOPBOOMas shown in FIGURE9. The pulleys in TOPBOOMmayneed to be temporarily
removed to perform this step. (Note: Makesure the CABLEis running OVERthe BOLTSconnecting the FRONTUPRIGHT
to the TOPBOOM.These mayalso have to be removedto performthis step.)
, Route the CABLE(16) around the PULLEYBLOCKas shown in FIGURE
¯ Route the CABLE(16) back over one pulley in the TOPBOOM,downthrough the PULLEYBRACKET(2) and over the second
pulley in the TOP BOOM. FIGURE 10

FIGURE11
IMPORTANT:
Tighten QUICK DISCONNECTLINK
SECURELY.
STEP 11
¯Attach the hook end of 82-1/2" CABLE(17) to the CABLESWIVEL(3) with one QU]:CKDISCONNECTLINK
IMPORTANT:Tighten the QUICKDISCONNECTLINK (8) securely.
¯ Route the 82-1/2" CABLE(17) under the WEIGHTSTACKas shownin FIGURE11.
I1/2 I1/2 I1/2 I 1/2 [ ~[/2 I 1/2 [
34 56
8

STEP 12
o Screw the threaded end of 82-1/2" CABLE(17) to the PULLEY
BRACKET(2) as shown in FIGURE12.
FIGURE 12
3/8X1-3/4"
FIGURE 13
STEP13
¯ Attach one 3-1/2" PULLEY(5) to the FRONTLEG(1) and one 3-1/2" PULLEY(5) to the BASECONNECTION(4) using
3/8 X 1-3/4" BOLTS(13) and two 3/8" LOCKNUTS.(Note: Makesure CABLE(17) is running under PULLEYS.)
9

SPRING PIN ADJUSTMENT
FIGURE 14
STEP 14
The832 LEGPRESSis equippedwith a springpin adjustment to acconunodatedifferen! sized users and allow easy entry and exit
fromthe machine.Touse, youmustslightly push against the foot plates to take tension off the pin.
Toset the correct amo~mtof tension in the cables, adjust the 832 LEGPRESSinto the last adjustment hole (so the LEGPRESS
is spread apart) and remove the WEIGHTSTACKPIN. Thread the 112-3/4" CABLE(16) into the HEADPLATEASSEMBLY
until the PULLEYBRACKET(2) is held against the TOPBOOMand the cable is slightly pulling up on the HEADPLATE.
Tighten the jan but securely. Next, thread the 82-1/2" CABLE(17) into the PULLEYBRACKET(2) until cable is tight,
tighten the jamnut securely.
THIS CONCLUDESTHE ASSEMBLYOF THE 415101 LEG PRESS ADAPTERKIT
3456
0 1 ] I I I
10