Paradox DGP2-641 User manual

LCD & Access Control LCD Keypad (V1.0)
DGP2-641 / DGP2-641AC
Reference and Installation Manual
DGP-641

© 2002 Paradox SecuritySystemsLtd.
Digiplexand DigiplexNE are trademarks of Paradox
SecuritySystems
PosiPINis a trademark of Position Technology

TABLE OF CONTENTS
1.0 INTRODUCTION ........................................................... 4
1.1 Specifications ....................................................................5
2.0 INSTALLATION ............................................................. 6
2.1 Connecting Keypad Zones ................................................6
2.2 Programmable Output .......................................................7
3.0 PROGRAMMING ....................................................... 12
3.1 Entering Module Programming Mode .............................12
3.2 Programming Methods ....................................................13
3.2.1 Feature Select Programming ..............................................13
3.2.2 Decimal Programming .........................................................13
3.3 Module Broadcast ...........................................................13
4.0 SYSTEM OPTIONS .................................................... 14
4.1 Partition Assignment .......................................................14
4.2 Display Access Code Entry .............................................14
4.3 Display Exit Delay Timer .................................................14
4.4 Display Entry Delay Timer ...............................................15
4.5 Confidential Mode ...........................................................15
4.6 Confidential Mode Timer .................................................16
4.7 Time Display Option ........................................................16
4.8 Muting .............................................................................17
4.9 Beep on Exit Delay ..........................................................17
4.10 Chime on Zone Closure ................................................17
4.11 Beep on Trouble ............................................................18

4.12 Keypad Tamper Enable ................................................18
4.13 Network Voltmeter .........................................................19
5.0 FEATURES FOR DGP2-641 ONLY ............................20
5.1 PGM State .......................................................................20
5.2 PGM Deactivation Mode .................................................20
5.3 PGM Base Time ..............................................................21
5.4 PGM Override .................................................................21
5.5 PGM Timer ......................................................................21
5.6 PGM Activation Event .....................................................22
5.7 PGM Deactivation Event .................................................22
6.0 FEATURES FOR DGP2-641AC ONLY .......................23
6.1 Assigning Doors To Partitions .........................................23
6.2 Reader’s Options ............................................................23
6.2.1 Reader’s LED To Follow Partition’s Status ..........................24
6.2.2 Reader’s Beep To Follow Partition's Status .........................24
6.2.3 Reader Feedback ................................................................24
6.2.4 Reader's LED Options Upon Access Granted .....................25
6.3 Door Lock Options ..........................................................25
6.3.1 Unlock on REX (Request For Exit) ......................................25
6.3.2 Door Unlocked Period ..........................................................25
6.3.3 Door Unlocked Period Extension .........................................26
6.3.4 Relock Door .........................................................................26
6.3.5 Door Unlocked Schedule .....................................................26
6.3.6 Card Activates Door Unlocked Schedule .............................27
6.4 Door Left Open Options ..................................................28
6.4.1 Door Left Open Access Alarm .............................................28
6.4.2 Door Left Open Interval Before Access Alarm .....................29
6.4.3 Door Left Open Pre-Alarm ...................................................29
6.4.4 Door Left Open Pre-Alarm Timer .........................................29
6.4.5 Door Left Open Alarm Feedback .........................................30

6.4.6 Beep Timer For Door Left Open Alarm ...............................31
6.5 Door Forced Open Options .............................................31
6.5.1 Door Forced Open Access Alarm ........................................31
6.5.2 Door Forced Open Feedback ..............................................32
6.5.3 Beep Timer For Door Forced Open Alarm ..........................32
6.6 Access Control PIN Entry Option ....................................32
6.6.1 Configuring The PosiPIN’s Keypad .....................................33
7.0 MESSAGE PROGRAMMING ..................................... 34
7.1 Special Function Keys .....................................................35
8.0 GLOSSARY ................................................................ 37

4 Reference & Installation Manual
1.0 INTRODUCTION
Thank you for choosing Paradox®Security Systems. The Digiplex™/
DigiplexNE Security Systems are advanced technology security
systems that will provide reliable security protection and powerful
features that are easy to use. The elegant and user-friendly
Digiplex™/DigiplexNE LCD Keypad will allow easy access to the
security system's functions and information at the touch of a button.
Since all programming is accomplished through the keypad, please
read this manual carefully.
As well as normal security system functions, the Digiplex/DigiplexNE
Access Control LCD Keypad (DGP2-641AC) can also be used for
access control. Access Control is designed to monitor and control the
access for up to 32 designated doors without the need of an
additional control panel. The events that occur on an Access Control
door can be logged in the control panel’s Event Buffer and can be
viewed through the keypad.
Each door to become an Access Control door requires an Access
Control LCD Keypad (DGP2-641AC), a reader (suggestion: PosiProx
CR-R880-A or PosiPIN CR-R885-BL), a REX device (suggestion:
Paradoor 460), a door contact, and a locking device.
If desired, door contacts can also be assigned to zones in the control
panel to link the doors to the Digiplex/DigiplexNE Alarm system. This
will allow you to use the same door for the Access Control system
and the alarm system. Only two of the Access Control features
require that the Access Control door's door contact be assigned to a
zone: Burglar Alarm on Forced Door and Access to Armed Access
Control Doors (refer to the Digiplex or DigiplexNE Reference &
Installation Manual).

Digiplex/DigiplexNE LCD Keypad 5n
1.1 SPECIFICATIONS
Power input: 12 to 16 Vdc, 80mA maximum
PGM current limit: 50 mA
Number of inputs: 1 (DGP2-641)
2 (DGP2-641AC)
Power indication: Yellow LED on
Locate indication:
Green and yellow LEDs flash simultaneously
Network fault
indication: Red and yellow LEDs flash alternately
Tamper Switch: Yes (also used to deactivate locate)
LCD: Super Twisted Nematic display (STN), wide
viewing angle, 2 lines of 16 characters, backlight
and contrast adjustable
Compatibility: DGP2-641: Any Digiplex/DigiplexNE Control
Panel
DGP2-641AC: Any DigiplexNE control panel or
Digiplex control panel V2.20ACC and higher

6 Reference & Installation Manual
2.0 INSTALLATION
The LCD keypads (DG2P-641 and DGP2-641AC) are connected to
the control panel's network in a star and/or daisy chain configuration.
This 4-wire communication network provides power and two-way
communication between the control panel and all modules connected
to it. Connect the four terminals labeled red, black, green and yellow
of each keypad to the corresponding terminals on the control panel
(refer to Figure 1 on page 8). Refer to the Digiplex or DigiplexNE
Reference & Installation Manual for the maximum allowable
installation distance from the control panel.
See Figure 4 on page 10 for connection drawings for the REX
device, reader, locking device and door contact to the desired DGP2-
641AC keypad. A typical installation is shown in Figure 2 on page 9.
The door contact follows the control panel’s EOL
definition. When EOL is enabled and the door contact is
not used, place a 1k
Ω resistor across the keypad’s Z1
and BLK input terminals. If EOL is not enabled, use a
jumper. If the REX device is not used, place a jumper
across the keypad’s Z2 and BLK input terminals.
2.1 CONNECTING KEYPAD ZONES
Each keypad has one traditional hardwired input terminal, allowing
you to connect one detector or door contact directly to the keypad.
For example, a door contact located at the entry point of an
establishment can be wired directly to the input terminal of the entry
point keypad instead of wiring the door contact all the way to the
control panel.
Connect the device to the keypad's input terminal as shown in Figure
1 on page 8. In order to communicate its status to the control panel,
devices connected to the keypad's input terminal must be assigned

Digiplex/DigiplexNE LCD Keypad 7n
to a zone in the control panel and the zone's parameters must be
defined. For more information on zone assignment, please refer to
the Digiplex or DigiplexNE Reference & Installation Manual. Please
note that even with the ATZ (zone doubling) feature enabled, the
keypad supports only one detection device.
2.2 PROGRAMMABLE OUTPUT
Each keypad has one on-board PGM. A PGM is a programmable
output that toggles to its opposite state (i.e. a normally open PGM will
close) when a specific event has occurred in the system (see section
5.0 on page 20). Upon activation, the PGM can provide 50mA to any
device connected to it. If the current drawn is to exceed the current
limit, a relay should be connected to the PGM as shown in Figure 1.
With the DGP2-641AC keypad, the PGM is reserved for the door lock
(refer to Figure 4 on page 10).

8 Reference & Installation Manual
Figure 1: Connecting the Keypad and Keypad Zone

Digiplex/DigiplexNE LCD Keypad 9n
Figure 2: Typical Access Control Installation (DGP2-641AC)
Figure 3: Access Control Overview (DGP2-641AC)

10 Reference & Installation Manual
Figure 4: Access Control Connections (DGP2-641AC)

Digiplex/DigiplexNE LCD Keypad 11n
Figure 5: Connecting a Shielded Routing Cable

12 Reference & Installation Manual
3.0 PROGRAMMING
Programming the DGP2-641 or DGP2-641AC LCD keypads is
simple. Enter the Module Programming Mode, enter the desired
section followed by the required data. When programming the
keypad, use the keypad’s programming sheets (found in the Digiplex/
DigiplexNE Modules’ Programming Guide) to keep track of which
sections were programmed and how. We strongly recommend you
read this entire manual before you begin programming.
The LCD keypad can also be programmed using the WinLoad
Security System Management Software. For more information, refer
to the WinLoad instructions or visit our web siteat www.paradox.ca.
3.1 ENTERING MODULE PROGRAMMING MODE
The keypad, like all other modules in the system, is programmed
through the control panel. To do so, you must first enter the Module
Programming Mode:
Step 1: From Normal Mode press and hold the [0] key.
Step 2: Enter the [INSTALLER CODE](by default 000000).
Step 3: Enter section [953] (DGP-48) / [4003] (DGP-NE96).
Step 4: Enter the keypad’s 8-digit [SERIAL NUMBER].
Step 5: Enter the 3-digit [SECTION] you want to program.
Step 6: Enter the required [DATA].
The control panel will then redirect all programming to the selected
keypad. Every time the [CLEAR]key is pressed it will revert to the
preceding step, unless entering in data in which case it will erase the
current data entry. Please note that the serial number is located on
the keypad's PC board or enter section [000] in Step 3 to view the
keypad’s serial number.

Digiplex/DigiplexNE LCD Keypad 13n
3.2 PROGRAMMING METHODS
The following methods can be used when programming the keypad:
3.2.1 FEATURE SELECT PROGRAMMING
Some sections are programmed by enabling or disabling
options. Within the sections, numbers from [1] to [8] represent
a specific keypad option. Press the key corresponding to the
desired option and the digit will appear in the display. This
means the option is enabled. Press the key again to remove
the digit from the display thereby disabling the option. Press
[ENTER]when options are set.
3.2.2 DECIMAL PROGRAMMING
Some sections require that a decimal value be entered. In this
method, any digit from 000 to 255 can be entered.
3.3 MODULE BROADCAST
The control panel’s Module Broadcast feature can be used to copy
the contents of one keypad to one or many other keypads.
Step 1: From Normal Mode press and hold the [0] key.
Step 2: Enter [INSTALLER CODE](default: 000000).
Step 3: Enter section [954] (DGP-48) / [4004] (DGP-NE96).
Step 4: Enter the [SERIAL #] of the source keypad. The source is the
programmed keypad whose data you want to copy to other
keypads.
Step 5: Enter the [SERIAL #] of the destination keypads. The
destination is the keypad(s) you want to program with the
source’s data. If you want to program more than one keypad
with the source’s data, enter the serial numbers of the
keypads one at a time.
Step 6: Once you have entered the serial numbers of the keypads
you want to program, press the [ACC] key.

14 Reference & Installation Manual
4.0 SYSTEM OPTIONS
The following sections pertain to the programming of options
belonging to both the DGP2-641 and DGP2-641AC Access Control
LCD keypads.
4.1 PARTITION ASSIGNMENT
SECTION [001]: OPTIONS [1] TO [8]
Each keypad in the system can be assigned to one or more
partitions. In section [001], options [1] to [8] represent partitions 1
through 8 respectively. To assign the keypad to a partition, simply
enable the option that corresponds to the desired partition. By
default, partitions 1 to 8 are enabled.
Section [001] options [5] to [8] can only be used if the
keypad is connected to a DigiplexNE (DGP-NE96) control
panel.
4.2 DISPLAY ACCESS CODE ENTRY
SECTION [003]: OPTION [1]
The digits of the User Access Codes can be displayed on the LCD
screen when they are entered.
Option [1] OFF= Digits are replaced by a * (default).
Option [1] ON = Access Code digits will be displayed.
4.3 DISPLAY EXIT DELAY TIMER
SECTION [003]: OPTION [2]
Based on the user's needs, an Exit Delay Timer will be programmed
to provide the user time to exit the partition before the system is
armed. The Exit Delay Timer's countdown can be displayed on the
LCD screen.

Digiplex/DigiplexNE LCD Keypad 15n
Option [2] OFF= Will not display Exit Delay timer (default).
Option [2] ON = LCD screen will display Exit Delay timer.
4.4 DISPLAY ENTRY DELAY TIMER
SECTION [003]: OPTION [3]
Based on the user's needs, an Entry Delay Timer will be
programmed to provide the user time to enter their User Access
Code before the alarm is triggered. The Entry Delay Timer's
countdown can be displayed on the LCD screen.
Option [3] OFF= Will not display the Entry Delay Timer (default).
Option [3] ON = LCD screen will display Entry Delay Timer.
4.5 CONFIDENTIAL MODE
SECTION [003]: OPTIONS [4] AND [5]
If the Confidential Mode is enabled and no actions are performed on
the keypad for a period of time, the LCD screen will appear as shown
in Figure 6 (page 16) and the “AC” and “STATUS” LED will be off until
either a button is pressed or an access code is entered. The period of
time in which no action is performed is defined by the Confidential
Mode Timer (005-255 seconds; refer to section 4.6 on page 16).
Confidential Mode is activated by enabling option [4]. Option [5]
regulates whether the LCD screen will be activated at the touch of a
button or only when an access code is entered.
Once the LCD screen is activated (by code or button), Normal Mode
will appear and display the date and time as shown in Figure 6 on
page 16. The status of the areas, the open zones for every area the
keypad is assigned, the Alarm Memory Display (if necessary) and the
Trouble Display (if necessary. See Digiplex or DigiplexNE User
Manual) will also scroll on the LCD screen. By default, options [4]
and [5] are OFF.

16 Reference & Installation Manual
Section [003]:
Option [4] OFF= Normal Mode
Option [4] ON = Confidential Mode
Option [5] OFF= LCD screen activated by entering an access code
Option [5] ON = LCD screen activated by pressing a button
Figure 6: LCD Screen
4.6 CONFIDENTIAL MODE TIMER
SECTION [007]
Section [007] determines the amount of time without action before
the keypad enters Confidential Mode. For more information on
Confidential Mode, refer to “Confidential Mode” on page 15. The
Confidential Mode Timer can be set from 005 seconds to 255
seconds. Default: 120 seconds.
4.7 TIME DISPLAY OPTION
SECTION [003]: OPTION [8]
The LCD keypad comes with a time display option that can display
the date as year/month/day or as day/month/year.
Option [8] OFF= Date displayed as yy/mm/dd (default).
Option [8] ON = Date displayed as dd/mm/yy.

Digiplex/DigiplexNE LCD Keypad 17n
4.8 MUTING
SECTION [004]: OPTION [1]
The keypad can be programmed not to emit audible sounds,
including Chimed zones. During Muting, the keypad will only emit the
Confirmation Beep, Rejection Beep, and beep when a button is
pressed.
Option [1] OFF= Audible sounds (default).
Option [1] ON = Mute.
4.9 BEEP ON EXIT DELAY
SECTION [004]: OPTION [2]
The keypad can beep once every second during the Exit Delay
Timer. During the final 10 seconds, it will beep more rapidly to
provide a final warning before the area is armed.
Option [2] OFF= Exit Delay beep disabled.
Option [2] ON = Exit Delay beep enabled (default).
4.10 CHIME ON ZONE CLOSURE
SECTION [004]: OPTION [4]
During the Chime Zone Time Period that the user sets, the keypad
can emit an intermittent beep whenever a zone with the Chime
feature enabled closes (see Digiplex or DigiplexNE User Manual for
details on Chime Zones). If the user does not set the Chime Zone
Time Period and this option is enabled, the Chime Zones will always
beep upon closure.
Option [4] OFF= Chime on Zone Closure disabled (default).
Option [4] ON = Chime on Zone Closure enabled.

18 Reference & Installation Manual
4.11 BEEP ON TROUBLE
SECTION [005]: OPTIONS [1] TO [4]
Potential troubles have been sorted into groups. With these options
enabled, the keypad will emit an intermittent beep tone whenever a
trouble condition from the Trouble Groups occurs in the system. The
intermittent beep will remain activated until the user enters the
Trouble Display or if the trouble is resolved. For a list of the troubles,
see the Digiplex or DigiplexNE Reference and Installation Manual.
The intermittent beep will be re-initialized whenever the trouble
condition re-occurs. By default, options [1] to [4] are OFF.
O ption [1] OFF= Beep disabled: System Troubles and Clock Loss.
Option [1] ON = Beep enabled: System Troubles and Clock Loss.
Option [2] OFF= Beep disabled: Communicator Troubles.
Option [2] ON = Beep enabled: Communicator Troubles.
Option [3] OFF= Beep disabled: Module and Network Troubles.
Option [3] ON = Beep enabled: Module and Network Troubles.
Option [4] OFF= Beep disabled: all Zone Troubles.
Option [4] ON = Beep enabled: all Zone Troubles.
4.12 KEYPAD TAMPER ENABLE
SECTION [006]: OPTION [5]
When tamper is enabled and the keypad's on-board tamper switch is
triggered, the keypad will send a Tamper report to the control panel
via the communication network.
Option [5] OFF= Keypad's tamper is disabled (default).
Option [5] ON = Keypad's tamper is enabled.