Paslode T250A-F16 User manual

MODEL T250A-F16
16 Gauge Angled
Finish Nailer
IMPORTANT!
DO NOT DESTROY
It is the customer’s responsibility to have all
operators and service personnel read and
understand this manual.
OPERATING MANUAL AND
SCHEMATIC
P

1 501043 1 T.H.S.C.S. 1/4-20 x 1/2
2 500921 1 Deflector
3 501332 4 S.H.C.S. 10x24 x 7/8
4 500909 1 Cap
*5 500927 1 Gasket
6 500913 1 Piston Stop
7 501288 1 Spring, Main Valve
*8 091023 2 O -Ring
*9 095406 1 O -Ring
10 501277 1 Main Valve Assembly
11 405430 1 O -Ring
12 500911 1 Piston
13 401130 1 Driv Lok Pin
14 500920 1 Driver Blade
15 091863 1 O -Ring
16 500369 1 O -Ring
17 500907 1 Sleeve
18 500917 1 Bumper
19 501404 1 Blade Seal
20 500908 1 Housing
21 501141 1 Label, Logo R
22 501140 1 Label, Logo L
23 026133 2 Roll Pin
24 501757 1 Spring
25 097748 1 Spring
26 097746 1 Pin Valve
27 092174 1 O -Ring
28 401958 1 Valve Body
29 501755 1 Adjustment Knob
30 500937 1 Brad Chanel
31 501039 1 Sequential Trigger
PARTS LEGEND T250A-F16, 500910
* Denotes Normal Wear Items.
** Make sure Warning Label (501302) is properly affixed.
Replace if necessary.
Label available at no charge through the Service Parts Dept.
DO NOT EXCEED MAXIMUM
RECOMMENDED AIR PRESSURE
60
0
120
60
0
120
Always wear hearing protection and eye protection
devices, including side shields when operating or
working in the vicinity of a tool.
Operate the tool using only the recommended air
pressure. Do not exceed the maximum air pressure
marked on the tool. Be sure the air pressure gauge is
operating properly and check it at least twice a day.
SAFETY INSTRUCTIONS
WEAR EYE AND HEARING PROTECTION
6
32 500940 1 Wire Belt Hook
33 501324 4 S.H.C.S. 10-24 x 3/4
34 501316 1 Pin Dowel
35 501301 1 Nose
36 500918 1 Front Plate
37 500924 1 Latch Clamp Spring
38 500923 1 Clamp Spring
39 404659 2 Roll Pin
40 402730 1 Pin
41 500939 1 Quick Clear Cover
42 501754 1 Upper W.C.E.
43 501753 1 Lower W.C.E.
44 500936 1 No-Mar Tip
45 501414 1 Spring, W.C.E.
46 402963 1 O -Ring
47 500928 1 End Plug
48 501756 1 Pin
49 501362 1 Rail, Magazine
50 500933 1 Follower
51 501150 1 Pull Back Lever
52 500944 1 Negator Spring
53 501148 1 Follower Core Assembly
54 501225 1 Follower Pin
55 500934 1 Spring, Follower
56 501224 1 Screw, #8-16 x 5/8 Plastite
57 501458 1 Right & Left Handle Kit
58 501223 2 Screw, #8-16 x 7/8 Plastite
59 501311 1 Nameplate
60 501302 1 Warning Label
61 501398 1 Torsion Spring, Quick Clear
62 402669 1 Trigger Pin
63 402668 1 Retaining Ring
Never use any bottled air or gases such as
oxygen to operate the tool since they could cause
the tool to explode.
AIR CONSUMPTION CHART
AIR CONSUMPTION - SCFM/FASTENER
70 80 90 100 110 120
.050
.045
.040
.035
.030
.040
AIR PRESSURE - PSIG
*
**
*
*
*
*
*
*
*
*
*
*
➔
➔

49
22
23
24
T250A-F16
500910
7
Piston Assembly
#501460
1
2
3
4
7
8
5
6
10
11 12
14
13
15
16
17
18
19
21 20
33
34 35
36
37
38 39
40
41
42
43
44
45
46
50
57
57
58
59
60
9
47
32
33
51
52
53
54
55
56
25
26
28
27
Follower
Assembly
#501457
Valve Assembly
#501459
48
61
31
30
Latch
Assembly
#501461
62
29
63
OPTIONAL:
Bump
Trigger
Assembly
#501048
WARNING
All parts must be periodically inspected and
replaced if worn or broken. Failure to do this can
affect the tool’s operation and present a safety
hazard.

Contact Trip Trigger Kit
The T250A-F16 comes with a Sequential Fire Trigger installed on the
tool. Using the Sequential Trigger, the user must fully depress the
work contact element (w.c.e) before squeezing the trigger and
successfully firing the tool. An optional Contact Trip Trigger,
designed for "bump" or "bounce" firing, is an included accessory.
Using the Contact Trip Trigger, the user is able to successively fire
fasteners by squeezing and holding the trigger and then "bumping" the
w.c.e. along the workpiece. Instructions for changing to the contact
trip trigger are included. Part No. 501048
Lubricants
Lubricating Oil 16 oz. Part No. 403720
Lubricaing Oil with Anitfreeze 8 oz. Part No. 219090
Chemplex 710 Lubricant 1lb. Part No. 403734
Degreaser Cleaner
Ideal cleaner for all Paslode tools. Part No. 219086
Safety Glasses
Clear Part No. 402510
Tinted Part No. 402512
ACCESSORIES
An Illinois Tool Works Company
888 Forest Edge Drive
Vernon Hills, Illinois 60061-3105
PRINTED IN U.S.A.
© 2006, Illinois Tool Works, Inc.
405653-2
03/06
Tool Case
Handy carrying case that conveniently stores your tool
with room for additional accessories. Part No. 501304
P