Paslode PF350-S User manual

1
MODEL PF350-S
Strip Nailer
IMPORTANT!
DO NOT DESTROY
It is the customers responsibility to have all
operators and service personnel read and
understand this manual.
OPERATING MANUAL AND
SCHEMATIC
P
502194-11
04/10
PRINTED IN U.S.A.
© 2010, Illinois Tool Works, Inc.
11/10

9
PF350-SFEATURES & BENEFITS
Metal
Exhaust Cap
For maximun
durability.
Tool Less Depth of
Drive
Provides precise control
of nail depth without adjusting
the compressor.
(on other side)
Powerful Motor
Consistently drives
into all engineered
lumber.
Compact
Design
Able to get into
tight spots
Bypass Follower
For fast 2-step loading.
Lock Out
Eliminates blank
firing.
Rear Load Magazine
Holds 2 strips or 84 nails.
Rafter Hook
Conveniently stowes the
tool.
Agressive
Work Contact
Grabs the wood
when toe nail-
ing.
Switchable Trigger
Switches from sequential to
bounce fire.
Light Weight Design
Easy to manuever with less arm
fatigue.

10
1 502004 1 Air Deflector
2 502062 1 Air De ector Gasket
3 501299 4 S.H.C.S. 1/4-20 x 1”
4 502003 1 Top Cap
5 502013 1 Top Cap Gasket
6 123984 1 Valve Spring
7 502859 1 O-Ring
8 211664 1 O-Ring
9 502434 1 Poppet Assembly
10 198028 1 O-Ring
11 502032 1 REMOVED
12 502056 1 Exhaust Seal
13 501300 1 S.H.C.S.1/4-20 x 1-1/4”
14 502011 1 Piston Seal
15 502012 1 Piston
16 502009 1 Sleeve
17 502010 1 Check Band
18 501218 1 Driver Blade
19 092235 1 O-Ring
20 502007 1 Bulkhead
21 401985 1 O-Ring
22 500866 1 Bumper
23 500729 1 Driver Blade Seal
24 502022 1 REMOVED
25 502807 1 Magazine Assembly
26 502019 1 Follower Claw
27 502021 1 Lockout Bar
28 511118 1 Follower Body
29 502031 2 B.H.C.S. #8-32 x 1/2”
30 502020 1 Follower Spring
31 502026 1 Negator Spring
32 502025 1 Drum Pin Assembly
33 403796 3 Roll Pin 1/8” x 1-1/4”
34 502017 2 B.H.C.S. 1/4-20 x 3/4”
35 502058 1 Magazine Logo Label
36 502038 1 B.H.C.S. #8-32 x 1
37 502016 2 REMOVED
38 502029 1 Magazine End Cap
39 502034 1 Housing Label Left
40 404325 2 Locknut #8-32
PARTS LEGEND
PF350-S,502000
* Denotes Normal Wear Items.
** Make sure Warning Label (502192) is properly affixed.
Replace if necessary.
Label available at no charge through the Service Parts Dept.
Always wear hearing protection and eye protection
devices, including side shields when operating or
working in the vicinity of a tool.
Operate the tool using only the recommended air
pressure. Do not exceed the maximum air pressure
marked on the tool. Be sure the air pressure gauge is
operating properly and check it at least twice a day.
41 502047 1 Lower W.C.E.
42 502046 1 Upper W.C.E.
43 502049 1 Detent Ball
44 502061 1 Detent Spring
45 404361 1 Roll Pin 1/8” x 1/2”
46 502050 1 Detent Body
47 502055 1 W.C.E. Spring
48 009016 4 S.H.C.S. 5/16-18 x 1” with Patch
49 095417 4 Lock Washer 5/16
50 502006 1 Nose
51 502014 2 Magazine Isolator
52 502042 1 O-Ring
53 091866 1 Roll Pin 1/8” x 3/4”
54 502053 1 Dual Mode Trigger
55 502040 1 Trip Lever
56 502060 1 Trigger Spring
57 092747 1 O-Ring
58 502035 1 Housing Label Right
59 502043 1 Lower Valve Spool
60 502041 1 Trigger Pivot Pin
61 1015358 1 O-Ring
62 196345 1 O-Ring
63 502192 1 Warning Label
64 502033 1 W.C.E. Guide Block
65 502446 1 Valve Pin with O-Rings
66 502059 1 Valve Pin Spring
67 502044 1 Upper Valve Spool
68 197913 1 O-Ring
69 502002 1 Housing with Grip
70 502914 1 Rafter Hook
71 502930 1 Rafter Hook Spring
72 502916 1 Rafter Hook Washer
73 444786 1 S.H.C.S. 1/4-20 x 5/8”
74 442681 2 Locknut 1/4-20
75 417147 1 O-Ring
76 502005 1 Housing End Plug
77 501300 2 S.H.C.S. 1/4-20 x 1-1/4”
78 502193 1 Actuation Setting Label
79 502036 1 Thumb Wheel
Never use any bottled air or gases such as oxygen
to operate the tool since they could cause the tool
to explode.
SAFETY INSTRUCTIONS
WEAR EYE AND HEARING PROTECTION
**
*
*
*
*
*
*
*
*
*
*
*
■
▲
▲
*
*
*
*
*
*
*
AIR CONSUMPTION - SCF/FASTENER
AIR PRESSURE - PSIG
DO NOT EXCEED MAXIMUM
RECOMMENDED AIR PRESSURE
80 502723 1 Roll Pin 3/8”x1-1/4”
.098
SCF
➔
▲ Apply Loctite 242 (Blue) Part
No. 093500
■
Apply Loctite 620 (Green) Part
No. 401491
Denotes New Change➔
®
®
•
Apply Loctite 271 (Red) Part No. 093422
®
•

11
PF350-S
502000
1
2
3
4
6
8
10
12
14*
13
15
16
18
19
21
20
41
42
43
44
45
46
47
48
49 50
51 53
54
55
56
57
33
60
61
65
33
64
66
67
68
7
5
22
23
52
59
62
69
74 75 76 77
71 73
Piston Assembly
#502008
39
58
120
120
325
120
3
120
79
Seal must be installed
in this position.
250
Upper
Work Contact
Assembly
#502734
Trigger
Assembly
#502435
80
28
29
30
32
31
38
40
15
15
*
63
25
78
Trigger
Valve
Assembly
#502908
26
27
33
34
35
36
29
9
Torque Values
IN/LBS
120
160
70
72
Note: Install check band
with thick side down.
➔
17