Patpet p-collar 360 User manual

Quick Start
p-collar 360
0.3.0.02.360000-12-00

Thanks for purchasing!
The dog training collar is designed to let dogs live safely, happily
and get along with people more harmoniously.
TINIWENeIN|IN(@) Do not use with aggressive dogs.
Aggressive dogs can cause severe injury and even death to their owner
and others. If you are unsure whether this product is appropriate for
your dog, please consult your veterinarian or certified trainer.
/\Vey:\ Un [e)\| Safety during on-leash training.
It is vitally important that you and your dog remain safe while learning
during on-leash training. Your dog should be on a strong leash, long
enough for him to attempt to chase an object, but short enough for him
not to reach aroad or other unsafe area. You must also be physically
strong enough to restrain your dog when he tries to chase.
(eV Ubi (e)\)) Risk of skin damage.
Please read and follow the instructions in this manual. Proper fit of the
collaris important. Acollar worn for too long or made too tight on the
pet’s neck may cause skin damage ranging from redness to pressure
ulcers. This condition is commonly known as bed sores.
¢ Avoid leaving the collar on the dog for more than 12 hours per day.
* When possible reposition the collar on the pet’s neck every 1 to 2
hours.
e Never connect a lead to the electronic collar; it will cause excessive
pressure onthe contacts.
¢lfarashorsoreis found, Stop using the collar until the skin
has healed.
¢ Ifthe condition persists over 48 hours, see your veterinarian.
¢ This productis nota toy, please keep away from children.
¢ This productis only used for healthy dogs.

Overview
A
4 i em ay \\| ) 5
J Pte IN °c
G
K D
E
F
G
000
>
c-roemmooaoanP?Y
Remote
. Signal LED
. Level +
Level -
. On/Off Button
. Tone Button
. Vibration Button
. Shock Button
. Battery Display
Dog 1 or dog 2 mode
. Switch dog 1 or
dog 2 mode
. Level Display
. Charging Port
. Hook&Loop Bandage
. Indicator light
. On/Off Button
. Contact Points
. Charging Port (with cover)

Setting Up the Product
Before you can use the Dog Training Collar, you must
set up the product as below steps:
1. Charging the Remote and the Receiver Collar.
. Prepare the Remote and turn it on.
. Prepare the Receiver Collar and turniton.
. Function test, test function of buttons before wearing it on dog.
. How to use the Test Lamp, test Shock function .
a a
fk
WD
. Pair the Remote and the Receiver Collar, pair them when the product
lose its code or pair forasecond collar.
Charging the Remote and the Receiver Collar
. Plugin and fully charge the Remote and the Receiver collar.
For the initial charge,be sure to charge it for 4 hours.
Subsequent charges only take 2-3 hours.
=
ND . When full charged, the red LED on the Receiver Collar will become
green. The Battery Display of the Remote will stop cycling and
appear full.
3. Please replace the rubber cover when the Receiver Collar is full
charged.
Tips: 1. Excessive charging will shorten battery life. Only charge
them when batteries are low.
2.When you’re not using the collar, please turn it off to increase
the battery life.
Note:
Please use the Output:DC 5V 500-800mA
charger to charge the product.
Don’t use a charger that does not meet the
specifications to charge the product.

Prepare the Remote
Turn ON/OFF the Remote
1.Long press the ON/OFF button toturn the remote ON.
2.LCD willbe lighted, and show the information of current channel,
battery power and levels. If not, please charge the remote.
3. Long press the ON/OFF button to turn the remote OFF.
Wesend aHook&Loop Bandage, youcan hang the remote
on your arm for easy carrying.
Complete
Prepare the Receiver
Assembly Collar
Please refer to the picture to wear the collar on the dog's neck.

Turn onthe Receiver Collar
¢ Press the On/Off Button the Green LED light is on.
* In normal mode, the Green LED will flash every 4 seconds,
indicating the Receiver Collar is on and ready to receive a signal
from the Remote.
Turn off the Receiver Collar
Press and hold the On/Off Button until the Red LED light shuts off
(This takes approximately 3 seconds).
NOTE:
To extend the life span of the batteries, please turn the Receiver
Collar off when it is not in use.
Function Test
We recommend you experience firsthand how the different levels
feelon yourself and always begin at the lowest level, increase toa
level that makes you personal comfortable.

1. Place one finger on two contact Points of the training collar.
2. Hold your remote approximately 2 ft. Away from the training collar.
Press the Vibration Button continuously for 1 to2 seconds.
You should feel continuous vibration.
3. Press == to decrease levels. Starting at level 1,press the Shock Button.
4. Increase the level until the sensation begins to feel uncomfortable.
NOTE: Continuous stimulation will transmit for no more than 10
consecutiye seconds. To reactivate, release and repress the button.
<p Tone: sends atone with non-adjustable level to
the Receiver Collar.
Vibration: sends a vibration with non-adjustable level tothe
4) } Receiver Collar.
the Receiver Collar.
Shock: sends 0-16 adjustable levels of static stimulation to
1
e3| | Slide up,control dog 1, slide down,control dog 2.
Long press to turn on, long press to turn off.
4b Press to increase the Shock Level.
<= | Press to decrease the Shock Level.
Note:
¢ The Shock Level can be adjusted from 1 to 16 levels ,please adjust
it properly according to your dog’s reaction at each level.
* Itis not recommended to press and hold the Vibration/Shock
Button toolong to avoid physical or psychological hurt to the dog.
Howto Use the Test Lamp
Shock Function Test
1. Turnon the Receiver Collar.
2. Hold the Test Lamp contacts against the Contact Points.

3. Press the Shock Button and the Test Lamp will be lighted. It will be
brighter accordingly with the Shock Level increasing.
Pair the Remote and the Receiver Collar
1.Usethe switch onthe Remote toselectDog1.
2.With the Remote turned on and the Receiver Collar turned off,
press and hold the ON/OFF Button on the Receiver Collar for
4-5 seconds.
3. The Red & Green LED will blink for about 10 seconds indicating
that itis ready for pairing.
4. Press and hold Tone Button and Vibration Button at the same time
for 2-3 seconds, the GreenLED onthe Receiver Collar will blink
for 5 times indicating successful pairing.
Pairing aSecond Collar with the Remote
Usethe switch on the Remote to select Dog 2.
Then follow the pairing steps above from 2-4.
Dog Training
Selecting The Contact Points and The Contact
spring sheet
For the best results, select the correct Contact Points based on your
dog’s coat.
You can use the Contact point separately,
oruse the Contact point and spring atthe same time.

Collar Fitting
Please fit the collar properly so that the Contact Points press firmly
against the dog’s skin. When properly fitted, you should be able to put
a finger between the Receiver Collar and dog’s neck.
Too loose: The Receiver Collar will move around the dog’s neck, the
Contact Points may hurt the dog’s skin.
Too tight: It may cause dog’s to breathe hard.
Caution: 1.Do not shave the pet’s neck as this
may increase the risk of skin irritation.
2.The collar should not be worn for more than 12
hours per day. Orit may cause skin irritation.
Find the Best Shock Level for Your Pet
The unit comes with Up and Down buttons to control the Shock Level,
with Level 1 being the lowest level and Level 16 being the highest. The
most suitable shock level for your dog depends on your dog’s
temperament and threshold for Shock. Always start at the lowest level
and work your way up. The appropriate level can be found when the dog
responds to the Shock witha mild reaction, such asa flick of the ear, a
lick of the lips, atensing of the neck muscles etc. The Shock Level may
vary depending on the training situation. When highly distracted, The
dog will require a higher level of Shock.
Device Information
Product Specification
Battery Type Rechargeable, lithium polymer battery
Battery Life(typical use) Remote: 27 days
Receiver: 11 days
Remote Waterproof Rating Non-Waterproof(Keep away from water)
Receiver Waterproof Rating | IEC 60529 IPX7, waterproof
Operating temperature range | From 0-40°C(from 32-104°F)
Wireless Range 300m(984 feet)

The unit need to be charged under any of below situations
1. The indicator light on the Receiver Collaris emitting ared color every
4 seconds or flashes rapidly.
2. The 3 barindicator onthe Remote LCD shows just 1 bar.
3. The indicator light on the Remote or Receiver Collar will not come on.
4. The indicator light onthe Remote or Receiver Collar comes on
momentarily when any of the Mode Buttons is pressed.
Others
Frequently Asked Questions
Is the Vibration/Shock
safe for my pet?
While the Vibration/Shock is unpleasant
itis harmless to your pet. Electronic
training devices require interaction and
training from the owner to achieve
desiredresults.
How old does my pet have
to be before using the
Remote Training Collar?
Your pet should be able to recognize
basic obedience commands suchas
“Sit” or “Stay”.Pets should be atleast 6
months old before using the Training
Collar.
Once my petis trained and
has been obeying my
commands, willhe have to
continue to wear the
Receiver Collar?
Probably not. You may need to reinforce}
training with the Receiver Collar from
time to time.
Is the Receiver Collar
waterproof?
Yes.
Willl getexactly 984 feet
ofrange withthe Remote
Training Collar?
The range of the Remote Training will
vary according to terrain, weather,
vegetation, as wellas transmission
from other radio devices. Refer to “To
maximize the distance” for tips on
maximizing your range.
10

The maximum amount of time you can press
the Vibration/Shock Button and deliver
How long can| Vibration/Shock to your pet continuously is
continuously deliver! 10 seconds. After this, there’s a time-out an
Vibration/Shockto | Vibration/Shock cannot be delivered for 5
my pet? seconds. After the 5 second time-out period,
Button can be pressed and Vibration/Shock
can be delivered again.
Troubleshooting Guide
*Make sure the Receiver Collar has been turned on.
elf yourrange is reduced from the first time you
use the Remote Training Collar, the battery(s)
may be lowin either the Remote or Receiver Collar.
¢Terrain, weather, vegetation, transmission from
other radio devices and many other factors can
impact the amount of range you have with the unit.
«Test the Receiver Collar. Refer to “How to use the
Test Lamp” for details.
«Increase the Shock Level. Refer to “Find the Best
Shock Level for Your Pet” for more information.
*Make sure the Receiver Collar’s Contact Points
are placed snugly against your pet’s skin. Refer to
“Collar Fitting” for more information.
My pet does not
respond when |
press a button.
The Receiver |-Make sure the Receiver Collar has been charged.
Collar will not | Fortheinitial charge, be sure tocharge itfor4
turn on. hours. Subsequent charges only take 2-3 hours.
-Make sure the Receiver Collaris on.
The Receiver |-If the Indicator Light does not light up when you
Collar is not press any button onthe remote, ensure thatthe
responding to | batteries are charged properly.
the Remote. «If the first two solutions did not resolve your problem,
Refer to “Pair the Remote and the Receiver Collar”.
11