Petsafe pawz away PWF00-13665 Setup guide

®
pawz away®
mini
pet barrier
operating and training guide
Model Number
PWF00-13665
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

2 Customer Care Center 1-800-732-2677
Important Safety Information
Explanation of Attention Words and Symbols used in this guide
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided,
could result in harm to your pet.
NOTICE is used to address safe use practices not related to personal injury.
Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive behavior. Aggressive
dogs can cause severe injury or death to their owners and others. If you are not sure that this product is right for
your dog, please talk to your veterinarian or a certified trainer.
This System is NOT a solid barrier. The system is designed to act as a deterrent, using Static Correction to
condition pets to remain outside of the established barrier area. It is important that you reinforce training with
your pet on a regular basis. Since the tolerance level to Static Correction varies from pet to pet, Radio Systems®
Corporation CANNOT guarantee that the system will in all cases keep a pet outside of the established barrier area.
Not all pets can be trained to avoid entering the barrier area. Therefore, if you have reason to believe that your
pet may harm himself or pose a danger to others if he is not kept from entering the barrier area, you should NOT
rely solely upon this system to restrict your pet. Radio Systems®Corporation shall NOT be liable for any personal
injuries, property damage, injury to or death of your pet, economic loss or any consequential damages sustained
as a result of any animal entering the barrier area.

www.petsafe.net 3
Proper fit of the collar is important. A collar worn for too long or made too tight on the pet’s neck may cause
skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.
- Avoid leaving the collar on the pet for more than 12 hours per day.
- When possible reposition the collar on the pet’s neck every 1 to 2 hours.
- Check the fit to prevent excessive pressure; follow the instructions in this manual.
- Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
- When using a separate collar for a lead, don’t put pressure on the electronic collar.
- Wash the pet’s neck area and the contacts of the collar weekly with a damp cloth.
- Examine the contact area daily for signs of a rash or a sore.
- If a rash or sore is found, discontinue use of the collar until the skin has healed.
- If the condition persists beyond 48 hours, see your veterinarian.
- For additional information on bed sores and pressure necrosis, please visit our website.
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear
stainless steel contacts. Some pets are sensitive to contact pressure. You may find after some time that your
pet is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue
daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.
You may need to trim the hair in the area of the Contact Points. Never shave the pet’s neck; this may lead
to a rash or infection.
• To prevent an unintended correction, do not perform set up procedures while the Receiver Collar is on your pet.
• If you are using a collar and leash for training, be sure the extra collar does not put pressure on the Contact Points
of the Receiver Collar.

4 Customer Care Center 1-800-732-2677
Thank you for choosing PetSafe®brand. You and your pet deserve a companionship that includes memorable moments
and a shared understanding together. Our products and training tools promote a lifestyle of protection, teaching, and
love — essentials that influence memories for a lifetime. If you have any questions about our products or training your
pet, please visit our website at www.petsafe.net or contact our Customer Care Center at 1-800-732-2677.
To get the most protection out of your warranty, please register your product within 30 days at www.petsafe.net. By
registering and keeping your receipt, you will enjoy the product’s full warranty and should you ever need to call the
Customer Care Center, we will be able to help you faster. Most importantly, PetSafe®will never give or sell your valuable
information to anyone. Complete warranty information is available online at www.petsafe.net.
Table of Contents
Components....................................................................... 5
Other Items You May Need ...............................................5
How the System Works ......................................................6
Key Definitions ...................................................................6
Operating Guide ..............................................................7
Install the Barrier Transmitter ......................................... 7
Set Up the Barrier Transmitter ....................................... 7
Test the Barrier Area ......................................................8
Fit the Receiver Collar on Your Pet ................................9
To Re-Thread the Collar ...............................................10
Receiver Collar Batteries..............................................11
Additional Features ......................................................12
Time Out Feature.........................................................12
Mode A, B, and AB Feature.........................................12
Programming the Mode Settings.................................14
Training Guide ...............................................................16
Begin Your Pet’s First Session ......................................16
Further Training............................................................16
Additional Information .....................................................17
Accessories....................................................................... 17
Troubleshooting ............................................................18
Terms of Use and Limitation of Liability ...........................19
Compliance ......................................................................20
Customer Care International............................................21
Perchlorate Battery .......................................................... 21
Warranty........................................................................... 21

www.petsafe.net 5
Components
Barrier Transmitter
(3 AAA Batteries not included)
Operating and
Training Guide
Test Light Tool
Receiver Collar
Cat Collar Strap
(2) 3-V Lithium
Batteries for
Receiver Collar
®
Other
Items
You
May
Need
• Drill and
mounting
hardware
• Non-metallic
collar and
leash
• Scissors
• Lighter

6 Customer Care Center 1-800-732-2677
How the System Works
The PetSafe®Pawz Away®Mini Pet Barrier keeps your pet away from a certain room, away from trash, off of furniture, etc.
Just place the Barrier Transmitter near the area your pet should avoid. The Mini Pet Barrier transmits an elliptical radio signal
adjustable up to 5 feet. Your pet wears a Receiver Collar with Contact Points that touch his neck. When your pet enters the
Barrier Area, he’ll hear a series of audible tones from the Receiver Collar and he will feel a safe Progressive Static Correction,
delivered through the Contact Points on his neck. The Progressive Static Correction will get his attention, but will not cause
harm. The correction continues until your pet leaves the Barrier Area. The PetSafe®Pawz Away®Mini Pet Barrier has been
proven safe, comfortable, and effective for pets at least 6 months old and 5 pounds or more.
Key Definitions
Barrier Transmitter: Transmits the wireless radio signal.
Barrier Area: Area that you want to prevent your pet from gaining access to.
Receiver Collar: Receives the radio signal from the Barrier Transmitter.
Contact Points: Deliver the safe Progressive Static Correction when your pet enters the Barrier Area.
Progressive Static
Correction: Static
correction begins at
the lowest level and
automatically increases to
maximum within 3 seconds
of first detection in the
Barrier Area.
Barrier
Transmitter
Barrier
Area
Receiver
Collar
LCD
Display
Window Up Button
Down Button
®
www.petsafe.net
ON
OFF
OPEN
Contact Points
On/Off Dial
Open Battery

www.petsafe.net 7
Operating Guide
Install the Barrier Transmitter
The Barrier Transmitter emits a radio signal from all sides in an elliptical pattern. The signal may transmit through
a wall or the ceiling/floor. The Barrier Transmitter can be placed laying flat on a surface or hung on a wall. If
you choose to hang the Barrier Transmitter, note that the signal becomes very directional—the signal will be
strongest directly in front of and behind the unit. The signal is weakest to the side of the unit.
Do not:
• Hang unit on a metal wall
• Place Barrier Transmitter on metal surfaces
• Place Barrier Transmitter near large metal objects such as refrigerators, washers, etc.
• Place Barrier Transmitter near audio speakers
Set Up the Barrier Transmitter
To prevent an unintended correction, never perform set-up procedures while your pet is wearing the Receiver Collar.
1. Turn over the Barrier Transmitter and rotate back cover counter-clockwise, removing
the back cover. Install three AAA alkaline batteries and replace the back cover. Turn
clockwise to secure cover.
2. Turn the Barrier Transmitter right side up and press the (+) button once to turn ON
the Barrier Transmitter. A black bar in the upper right hand corner of the LCD display
window indicates that the Barrier Transmitter is set to mode A* (2A). A second black
bar in the bottom of the LCD display indicates the range is set to one segment.
3. Each segment represents approximately 5 inches from the unit. You can create a Barrier
Area of 5 inches to 30 inches from the unit. Using the (+) and (-) buttons, adjust the
range to fit the desired pet Barrier Area.
2A
Step
1
Step
2

8 Customer Care Center 1-800-732-2677
*All Mini Pet Barriers and Receiver Collars are preset to mode A. The A and B mode feature is designed to be used in
multiple pet households where you may want one pet to be able to access an area while preventing access by another
pet. For single pet households, you will not need to operate the Barrier Transmitter in any mode other than A. Please
see the Additional Features section of this operating and training guide (beginning on page 12) for instructions on how
to utilize mode A and B.
Test the Barrier Area
1. Keeping your hands away from the Contact Points, use the edge of the Test Light
Tool to turn the receiver battery door to the ON position.
2. Hold the Receiver Collar with the Contact Points facing up. Place the Test Light Tool
on the Contact Points so that the wire in the Test Light Tool touches the Contact
Points (3A). The PetSafe®logo on the Receiver Collar should face the Transmitter.
3. Hold the Receiver Collar at the approximate height of your pet’s neck (3B). Start
outside of the range and walk slowly toward the Barrier Transmitter. As you reach
the Barrier Area, the Receiver Collar emits a series of high-pitched tones. For each
tone you hear, you should notice the Test Light flashing which indicates that a
Progressive Static Correction is being delivered. The Receiver Collar’s tone is easily
heard by pets but may be at a volume level difficult for some humans to hear.
4. Check the range of the Barrier Area from multiple angles to ensure you are getting
the desired coverage.
Note: Should you find that you are not getting the desired range at the maximum setting,
move the Barrier Transmitter a foot, or change from its standing-on-end position to
laying flat. Metal objects can alter the magnetic field and change the transmitting signal
range. The effect on the range depends on the size and shape of the objects. Signal
range can be reduced if the Barrier Transmitter is placed on a concrete floor, due to steel
reinforcement in the concrete. For best range results, place the Barrier Transmitter
on a nonconductive surface, i.e., wood floor or table. Placing the Barrier Transmitter
beneath sofas and beds can reduce the range due to the metal springs altering the
magnetic field.
3A
3B
Step
3

www.petsafe.net 9
Fit the Receiver Collar on Your Pet
Important: Proper fit and placement of your Receiver Collar is necessary for effective operation. The Contact
Points must have direct contact with your pet’s skin on the underside of his neck.
Proper fit of the collar is important. A collar worn for too long or made too tight on the pet’s neck may cause skin damage.
Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.
• Avoid leaving the collar on the pet for more than 12 hours per day.
• When possible reposition the collar on the pet’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the pet’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
• For additional information on bed sores and pressure necrosis, please visit our website.
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear stainless steel contacts.
Some pets are sensitive to contact pressure. You may find after some time that your pet is very tolerant of the collar. If so, you may
relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue
use until the skin has fully healed.
You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead to a rash or infection.
To assure a proper fit, please follow these steps:
1. Using the edge of the Test Light Tool, turn the battery door to the OFF position.
2. Start with your pet standing comfortably (4A).
3. Place the Receiver collar on your pet so that the PetSafe®logo is facing your pet’s chin. Center
the Contact Points underneath your pet’s neck, touching the skin. If your pet has a long or
thick coat then it may be necessary to trim the hair around the Contact Points to make sure
that contact is consistent.
4A
Note: The Receiver Collar comes with Short Contact Points. Long Contact Points are available and can be
purchased through the Customer Care Center. Please see the Accessories section of this Operating and Training
Guide for more information.
Step
4

10 Customer Care Center 1-800-732-2677
4. Adjust the tightness of the Receiver Collar to fit your pet’s neck. Check the
tightness of the Receiver Collar by inserting one finger between the end of a
Contact Point and your pet’s neck. The fit should be snug but not constricting
(4B).
5. Allow your pet to wear the Receiver Collar for several minutes then recheck
the fit. Check the fit again as your pet becomes more comfortable with the
Receiver Collar.
6. Once you are satisfied with the fit of the Receiver Collar then you may trim
any excess collar strap as follows (4C):
a. Mark the desired length of the Receiver Collar with a pen. Allow for growth if
your pet is young or grows a thick winter coat.
b. Remove the Receiver Collar from your pet and cut off the excess.
c. Before placing the Receiver Collar back onto your pet, seal the edge of the
cut collar by applying a flame along the frayed edge.
4B
4C
To Re-Thread the Collar
Slide Buckle
Ridges
The slide buckle prevents the collar from becoming loose around your pet’s neck.
The ridges must be facing up; the collar will slip if it is not properly threaded.

www.petsafe.net 11
Receiver Collar Batteries
The PetSafe®Pawz Away®Receiver Collar uses two 3-volt Lithium coin cell batteries, size
CR2032. Replacement batteries can be found at many retailers or through the Customer
Care Center. Contact the Customer Care Center at 1-800-732-2677 or visit our website
at www.petsafe.net to locate a retailer near you.
To replace the batteries:
1. Using the edge of the Test Light Tool, turn the battery door to the OPEN position.
2. Lift the battery door out and turn the door over. The two 3-volt Lithium coin cell
batteries are stored inside the door.
3. Remove the old batteries and insert new batteries with the positive (+) side facing
the battery door lid.
4. Insert battery door back into the Receiver Collar and turn to either the OFF or ON
position to lock the door in place.
Battery life will vary depending on how often your pet tests the system and receives
a Static Correction. Check the Receiver Collar and Barrier Transmitter every month to
ensure the system is working properly. To prolong battery life, it is recommended that
you turn the Receiver Collar and Barrier Transmitter OFF when not in use.
ON
OFF
OPEN
ON
OFF
OPEN
Open
Battery

12 Customer Care Center 1-800-732-2677
Additional Features
Time Out Feature
For your pet’s safety, the Receiver Collar has a built in Time Out feature. If your pet stays in the Barrier Area for longer
than 15 seconds the Receiver Collar will stop delivering the Progressive Static Correction. The Receiver Collar will
then administer a random single Static Correction every 5 to 10 seconds at the maximum level until the pet leaves the
Barrier Area. Once your pet leaves the Barrier Area, the Receiver Collar resets itself and will deliver a Progressive Static
Correction the next time your pet enters the Barrier Area.
Mode A, B, and AB Feature
For multiple pet households, additional PetSafe®Pawz Away®Receiver Collars can be purchased to work with one or
more PetSafe®Pawz Away®Indoor Barrier Transmitters. You can set up an unlimited number of Barrier Transmitters in
your home and an unlimited number of Receiver Collars can be used with one or more Barrier Transmitters. If you have
multiple pets, you may want to allow one pet access to an area while denying access to another pet. With the purchase
of additional Receiver Collars and Barrier Transmitters, you can accomplish this by using the Mode A and Mode B
functions.
All PetSafe®Pawz Away®Mini Barrier Transmitters and Receiver Collars come preset to mode A. Each Receiver Collar
can operate in one of two different modes—A or B. Each Barrier Transmitter may be set to either A, B or AB mode to
allow for multiple configurations.

www.petsafe.net 13
When the Barrier Transmitter and Receiver Collar are set to mode A,
the Barrier Transmitter denies access to pets wearing a Receiver Collar
programmed to mode A. Receiver Collars set to mode B will not pick
up the signal from a Barrier Transmitter set to mode A.
When the Barrier Transmitter and Receiver Collar are set to mode B,
the Barrier Transmitter denies access to pets wearing a Receiver Collar
programmed to mode B. Receiver Collars set to mode A will not pick
up the signal from a Barrier Transmitter set to mode B.
When the Barrier Transmitter is set to mode AB, the Barrier
Transmitter denies access to all pets wearing the Receiver Collar, no
matter which mode the receiver is programmed to.
Barrier
Transmitter
Barrier
Transmitter
Barrier
Transmitter

14 Customer Care Center 1-800-732-2677
Programming the Mode Settings
All programming is done through the Barrier Transmitter and the programming is synchronized with the Receiver
Collar. The Receiver Collar cannot be programmed separately from the Barrier Transmitter.
You may synchronize multiple Receiver Collars to a single Barrier Transmitter at one time. However, make sure any
Receiver Collar you do not wish to synchronize is turned OFF during the programming procedure. Any collar that is
within 30 inches of the Barrier Transmitter and turned ON may be reprogrammed. Familiarize yourself with the steps
outlined below before attempting to program the Barrier Transmitter and Receiver Collar.
To prevent an unintended correction, do not perform set up procedures while the Receiver Collar is on your pet.
1. Gather the Receiver Collar(s) you wish to synchronize with the Barrier Transmitter. Turn the Receiver Collar(s) ON
and place less than one foot from the Barrier Transmitter.
2. Turn the Barrier Transmitter OFF by pressing the (-) button until there are no bars displayed in the LCD window.
Remove the back cover.
3. The mode switch is located inside the transmitter and
is preset to mode A. Move the switch to the center
position for mode B or to the right position for mode
AB (5A). Once you have selected the desired mode,
replace the back cover.
Note: If you have selected mode AB you do not need
to proceed with programming the receiver in the next
steps. Receiver Collars set to mode A or mode B will
each receive the radio signal from a Barrier Transmitter
set to mode AB.
Inside
Back
Cover
Transmitter
Inside
View
5A

www.petsafe.net 15
4. To program the Receiver Collar to either mode A or mode B, press and hold the (-) button and then press the (+) button
for approximately 5 seconds. Programming is complete when you hear a series of three beeps from the Receiver Collar.
5. Once the Receiver Collar has been programmed, press the (+) button to turn the
Barrier Transmitter ON. Check to make sure the black bar(s) appear on the LCD screen indicating the mode you have
selected (5B) and reset the Barrier Transmitter to the desired range.
Mode AMode
BM
ode AB
5B

16 Customer Care Center 1-800-732-2677
Training Guide
The PetSafe®Pawz Away®Mini Pet Barrier operates on the principle of positive and negative reinforcement. Your pet
will learn to avoid the Barrier Areas you have set after receiving a Progressive Static Correction (negative reinforcement)
and your pet will learn that he is more comfortable when he avoids the Barrier Areas (positive reinforcement).
In some cases, it may not be necessary to train your pet. You can let your pet wander freely to determine the new
boundaries. Monitor your pet during his first session. Pets learn at different rates and it may take several times for
your pet to successfully understand and honor the Barrier Areas.
Begin Your Pet’s First Session
1. Move your pet away from the Barrier Area.
2. Activate the Receiver Collar by turning the battery door to the ON position. Place the Receiver Collar around your
pet’s neck. Be sure that the Receiver is directly under your pet’s neck.
3. Allow your pet to wander freely to learn the new boundaries.
Further Training
If your pet is confused or unsure how to avoid the Barrier Areas then you may need to teach your pet how to do so by
following these easy training steps:
1. Place a second non metallic collar on your pet ABOVE the Receiver Collar and attach a long leash.
Be sure the extra collar does not put pressure on the Contact Points of the Receiver Collar.
2. Walk your pet toward the Barrier Area. As soon as you hear the tone or you see that your pet is receiving a Static
Correction, gently pull him away from the Barrier Area and back into the safe zone.
3. Reward your pet with praise each time he leaves the Barrier Area.
4. Practice this technique a few times until you feel that your pet is mastering avoidance of the Barrier Areas.
Be sure to never force or entice your pet to enter the Barrier Areas.

www.petsafe.net 17
Additional Information
• The system should only be used with healthy pets. Contact your veterinarian if you have concerns about the medical
condition of your pet (medication, pregnant, heart conditions, etc).
• This system is not for vicious or aggressive pets. If your pet may pose a threat to others, DO NOT USE THIS SYSTEM. If
you are unsure if your dog is aggressive, please consult your veterinarian or a certified trainer.
Accessories
To purchase additional accessories for your PetSafe®Pawz Away®Mini Pet Barrier, contact the Customer Care Center at
1-800-732-2677 or visit our website at www.petsafe.net to locate a retailer near you.
Component Part Number
Battery – 3 Volt Lithium (two pack - size CR2032) RFA-35-11
Replacement Strap RFA-308
Extra Receiver Collar PWF00-13664
Extra Barrier Transmitter PWF00-14040
Replacement Short and Long Contact Points RK-17
Receiver Collar Battery Door RFA-394

18 Customer Care Center 1-800-732-2677
Troubleshooting
Barrier Transmitter does not
appear to work.
•Check segment indicator on Barrier Transmitter.
•Check/replace batteries in Barrier Transmitter.
•Increase the Barrier Area range on the Barrier Transmitter.
•Check that the Barrier Transmitter setting corresponds to the Receiver
Collar setting. (i.e. Barrier Transmitter is set to mode A and Receiver Collar
is synchronized to pick up mode A)—refer to Additional Features section
beginning on page 12 for instructions.
Barrier Area range is too low. •Check/replace batteries in Receiver Collar.
•Adjust Barrier Transmitter range to increase Barrier Area size.
Barrier Area range is too high. •Adjust Barrier Transmitter range to decrease Barrier Area size.
Pet seems to receive no
stimulation.
•Check/replace batteries in Receiver Collar.
•Use Test Light Tool to check for static correction.
•Check Receiver Collar fit to ensure Contact Points have direct skin contact.
•Check the setting on the Barrier Transmitter.
Unable to hear Receiver Collar
tone.
•Check/Replace batteries in Receiver Collar.
•Pets easily hear tone but it may be a volume level that is difficult for you to
hear.
•Use the Test Light Tool to check Receiver Collar for static correction.
No segments on Barrier
Transmitter.
•Press the (+) button.
•Check/replace batteries in Barrier Transmitter.

www.petsafe.net 19
Terms of Use and Limitation of Liability
1. Terms of Use
This Product is offered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,
conditions, and notices.
2. Proper Use
This Product is designed for use with pets where training is desired. The specific temperament of your
pet may not work with this Product. We recommend that you not use this Product if your pet is less than
8 pounds or if your pet is aggressive. If you are unsure whether this is appropriate for your pet, please
consult your veterinarian or certified trainer.
Proper use includes reviewing the entire Guide provided with your Product and any specific Caution
statements.
3. No Unlawful or Prohibited Use
This Product is designed for use with pets only. This pet training device is not intended to harm, injure or
provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local
laws.
4. Limitation of Liability
In no event shall Radio Systems Corporation®be liable for any direct, indirect, punitive, incidental, special
or consequential damages, or any damages whatsoever arising out of or connected with the use or
misuse of this Product. Buyer assumes all risks and liability from the use of this Product.
5. Modification of Terms and Conditions
Radio Systems Corporation®reserves the right to change the terms, conditions and notices under which
this Product is offered.

20 Customer Care Center 1-800-732-2677
Compliance
FCC/Canada
This Class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a residential environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction guide, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a practical installation. If this equipment causes harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Relocate the interfered receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different to that to which the receiver is connected.
• Contact the Customer Care Center at 1-800-732-2677.
This device complies with Industry Canada Rules. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modifications to the equipment, not approved by Radio Systems®Corporation, could result in
not meeting compliance with FCC regulations and could void the user’s authority to operate the equipment.
Australia
This device complies with the applicable EMC requirements specified by the ACMA (Australian Communications and
Media Authority).