Patpet p-collar 350 User manual

-)
Talay
Quick Start
p-collar 350
Please read the quick start before beginning.
0.3.0.02.350000-14-11

Thanks for purchasing!
Patpet dog training collar is designed to let dogs live safely, happily
and get along with people more harmoniously.
TINYNPN IN| [Ne] Do not use with aggressive dogs.
Aggressive dogs can cause severe injury and even death to their owner
and others. If you are unsure whether this product is appropriate for
your dog, please consult your veterinarian or certified trainer.
7\\ey:\ Up [@)\\|) Safety during on-leash training.
It is vitally important that you and your dog remain safe while learning
during on-leash training. Your dog should be on astrong leash, long
enough for him to attempt to chase an object, but short enough for him
not to reach aroad or other unsafe area. You must also be physically
strong enough to restrain your dog when he tries to chase.
(e7:\U i [@)\|) Risk of skin damage.
Please read and follow the instructions in this manual. Proper fit of the
collaris important. Acollar worn for too long or made too tight on the
pet’s neck may cause skin damage ranging from redness to pressure
ulcers. This condition is commonly known as bed sores.
¢ Avoid leaving the collar on the dog for more than 12 hours per day.
° When possible reposition the collar on the pet’s neck every 1 to 2
hours.
« Never connecta lead to the electronic collar; it will cause excessive
pressure onthe contacts.
¢lfarashor sore is found, discontinue use of the collar until the skin
has healed.
¢ If the condition persists beyond 48 hours, see your veterinarian.
¢ This productis nota toy, please keep away fromchildren.
¢ This productis only for use with healthy dogs.

Overview
. LED Indicator
. Battery Display
. Channel Display
. High Shock Level Warning
. On/Off Button
. Vibration Level Display
. Level +
. Shock Level Display
. Level-
.¢ Channel Conversion Button
* Press and Holdit for setting
Vibration&Shock Level
. Tone Button
. Vibration Button
. Shock Button
. Charging Port
Am
0OW
S©-TroOaTmTmMoowv0r,r
r
Zernk
N
Remote
.Contact Points
.Conductive Silicone
.Charging Port (with cover)
.On/Off Button
.LED Indicator
Receiver Collar

Setting Up the Product
Before you can use the Dog Training Collar, you must
set up the product as below steps:
1. Charging the Remote and the Receiver Collar.
2. Prepare the Remote and turn it on.
3. Prepare the Receiver Collar, install Contact Points, Conductive
Silicone, and assembly collar, turn the Receiver Collar on.
4. Function test, test function of buttons before wearing it on dog.
. How to use the Test Lamp, test Shock function or use as a screw driver.
6. Pair the Remote and the Receiver Collar, pair them when the product
lose its code or pair forasecond collar.
Charging the Remote and the Receiver Collar
1. Plugin and fully charge the Remote and the Receiver collar. This may
take 2-3 hours.
2. When full charged, the red LED on the Receiver Collar will become
green. Thered LED on the Remote will flash and the Battery Display
will stop cycling and appear full.
3. Please replace the rubber cover when the Receiver Collar is full
charged.
a
Tips: 1. Excessive charging will shorten battery life. Only charge them
when batteries are low.
2.When you’re not using the collar, please turn it off to increase
the battery life.
Charger

Note:
1. Charge with the power adapter included in the product, other
specifications of the power adapter may cause damage to the product.
2. If you lostit, please use the same specifications of the power adapter
for replacement (Output:5VDC 800mA) orcontactus.
Prepare the Remote
Turn ON/OFF the Remote
1. Press the ON/OFF Button onthe remote once to turnit ON.
2.LCD willbe lighted, and show the information of current channel,
battery power and levels. If not, please charge the remote.
3. Press and hold the ON/OFF Button onthe Remote to turn it OFF, until
the LCD off, then release. It may take 2-3 seconds.
Prepare the Receiver
Install the Contact Points & Conductive Silicone
1. Select the correct Contact Points and Conductive Silicone length for
your dog’s coat type:
¢ For dogs with thicker coats, Use 2pcs longer Contact Points and
Conductive Silicones.
¢ For dogs with shorter coats, Use 2pcs shorter Contact Points and
Conductive Silicones.
Note: Notinstall the Metal Contact Points when shock function is not be
used.
2. Insert the Contact Points into the ports of the collar, rotate clockwise
totightenthem(1A).
3. Install the Conductive Silicone onto the Contact Points to make it
softer, it may better to the dog’s skin(1B).
Assembly Collar
1. Unhitch the nylon belt and take off the Slide Buckle(2A).
2. Thread the strap through the Receiver Collar(2B).
3. Thread the slide buckle through the strap(2C). 5

4. Thread the strap through the side release buckle(2D).
5. Thread the excess strap through the slide buckle to make sure the collar
is secured tightly(2E).
Turn onthe Receiver Collar
¢ Press the On/Off Button the Green LED light comes on.
¢ Innormal mode, the Green LED will flash every 4 seconds, indicating the
Receiver Collar is on and ready to receive a signal from the Remote.
Turn off the Receiver Collar
¢ Press and hold the On/Off Button until the Red LED light shuts off
(This takes approximately 3 seconds).
* Release the On/Off Button.
NOTE: To extend the life of the batteries, please turn the Receiver Collar
off when it is notin use.
Function Test
We recommend you experience firsthand how the different levels feel
on yourself and always begin at the lowest level, and increase the
levels up to your personal comfort levels.
1. Place one finger over both Contact Points of the training collar.
2. Hold your remote approximately 2 ft. from the training collar. Press
the Vibration Button continuously for 1 to 2 seconds. You should feel
continuous vibration.
6

3. Press and hold until the Shock Level display flashes, press +/- to
increase/decrease levels. Starting at level 1,press the Shock Button.
4. Increase the level until the sensation begins to feel uncomfortable.
NOTE: Continuous stimulation will transmit for no more the 10 continuous
seconds. To reactivate, release and repress the button.
Vibration: sends 1-8 adjustable levels of vibration to the
Receiver Collar.
Y
Q,
Tone: sends atone with non-adjustable level to the Receiver
Collar.
Shock: sends 1-16 adjustable levels of static stimulation to
the Receiver Collar. Warning sign A shows when the
levels over8.
Channel Conversion: Press shortly once to change dog [iS
ordog channel.
Vibration & Shock Level Adjustment: Press and hold until the
Vibration/Shock Level display flashes, press +/- toincrease/
decrease levels.
Press to increase the Shock/Vibration Level.
Press to decrease the Shock/Vibration Level.
Note:
« Press and hold until the Vibration/Shock Level display flashes to
set Vibration/Shock Level.
¢ The Shock Level can be adjusted from 1 to 16 levels and the Vibration
Level from 1 to 8 levels; please adjust it properly as per your dog’s
reaction.
¢ Itis not recommended to press and hold the Vibration/Shock Button
too long to avoid physical or psychological hurt to the dog.
How to Use the Test Lamp
Shock Function Test
1. Turnonthe Receiver Collar.
2. Hold the Test Lamp contacts against the Contact Points (or
Conductive Silicone).

3. Press the Shock Button and the Test Lamp will be lighted. It will be
lighter accordingly with the Shock Level increasing.
As a Screw Driver
Use the Test Lamp to tighten or loosen the Contact Points when prepare
the Receiver Collar.
Pair the Remote and the Receiver Collar
1.Usethe Dog (/2) Button onthe Remote to select Dog fy.
2.With the Remote turned on and the Receiver Collar turned off, press
and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.
3. The Red & Green LED will blink for about 10 seconds indicating that
itis ready for pairing.
4. Press and hold the first Tone Button and the second Vibration Button
at the same time for 2-3 seconds, the Green Led on the Receiver
Collar will blink for 5 times indicating successful pairing.
Pairing aSecond Collar with the Remote
1. Use the Dog (1/2)Button on the Remote to select Dog/& . Then follow
the above pairing steps from 2-4.
Dog Training
Selecting The Contact Points and The Conductive
Silicone
For the best results, select the correct Contact Points based on your
dog’s coat.
¢ For dogs with thicker coats, Use 2pcs longer Contact Points and
Conductive Silicones. 8

* For dogs with shorter coats, Use 2pcs shorter Contact Points and
Conductive Silicones.
Collar Fitting
Please fit the collar properly so that the Contact Points press firmly
against the dog’s skin. When properly fitted, you should be able to put
a fingerin between the Receiver Collar and dog’s neck.
Too loose: the Receiver Collar will move around the dog’s neck, the
Contact Points may hurt the dog’s skin.
Too tight: it may cause dog’s to breathe hard.
Caution: 1.do not shave the pet’s neck as this
may increase the risk of skin irritation.
2.the collar should not be worn for more than 12
hours per day. Orit may cause skin irritation.
Find the Best Shock Level for Your Pet
The unit comes with Up and Down buttons to control the Shock Level,
with Level 1 being the lowest level and Level 16 being the highest. The
level of Shock best suited for your dog depends on your dog’s
temperament and threshold for Shock. Always start at the lowest level
and work your way up. The appropriate level can be found when the dog
responds to the Shock witha mild reaction, such asa flick of the ear, a
lick of the lips, atensing of the neck muscles etc. The Shock Level may
vary depending on the training situation. When highly distracted, dog’s
will require a higher level of Shock.
Device Information
Product Specification
Battery Type Rechargeable, lithium polymer battery
Battery Life(typical use) Remote: 27 days
Receiver: 5 days
Remote Waterproof Rating Non-Waterproof(Keep away from water)
Receiver Waterproof Rating | IEC 60529 IPX7, waterproof
Operating temperature range | From 0-40°C(from 32-104°F)
Wireless Power 10mWw
Wireless Range 300m(984 feet)

The unit need to be charged under any of below situations
1. The indicator light on the Receiver Collaris emitting ared color every
4 seconds or flashes rapidly.
2. The 3 barindicator onthe Remote LCD shows just 1 bar.
3. The indicator light on the Remote or Receiver Collar will not come on.
4. The indicator light onthe Remote or Receiver Collar comes on
momentarily when any of the Mode Buttons is pressed.
Others
Frequently Asked Questions
Is the Vibration/Shock
safe for my pet?
While the Vibration/Shock is unpleasant
itis harmless to your pet. Electronic
training devices require interaction and
training from the owner to achieve
desiredresults.
How old does my pet have
to be before using the
Remote Training Collar?
Your pet should be able to recognize
basic obedience commands suchas
“Sit” or “Stay”.Pets should be atleast 6
months old before using the Training
Collar.
Once my petis trained and
has been obeying my
commands, willhe have to
continue to wear the
Receiver Collar?
Probably not. You may need to reinforce}
training with the Receiver Collar from
time to time.
Is the Receiver Collar
waterproof?
Yes.
Willl getexactly 984 feet
ofrange withthe Remote
Training Collar?
The range of the Remote Training will
vary according to terrain, weather,
vegetation, as wellas transmission
from other radio devices. Refer to “To
maximize the distance” for tips on
maximizing your range.
10

The maximum amount of time you can press
the Vibration/Shock Button and deliver
How long can| Vibration/Shock to your pet continuously is
continuously deliver! 10 seconds. After this, there’s a time-out an
Vibration/Shockto | Vibration/Shock cannot be delivered for 5
my pet? seconds. After the 5 second time-out period,
Button can be pressed and Vibration/Shock
can be delivered again.
Troubleshooting Guide
*Make sure the Receiver Collar has been turned on.
elf yourrange has reduced from the first time you
used the Remote Training Collar, the battery(s)
may be lowin either the Remote or Receiver Collar.
¢Terrain, weather, vegetation, transmission from
other radio devices and many other factors can
impact the amount of range you have with the unit.
«Test the Receiver Collar. Refer to “How to use the
Test Lamp” for details.
«Increase the Shock Level. Refer to “Find the Best
Shock Level for Your Pet” for more information.
*Make sure the Receiver Collar’s Contact Points
are placed snugly against your pet’s skin. Refer to
“Collar Fitting” for more information.
My pet does not
respond when |
press a button.
The Receiver |-Make sure the Receiver Collar has been charged.
Collar will not | Fortheinitial charge, be sure tocharge itfor4
turn on. hours. Subsequent charges only take 2-3 hours.
-Make sure the Receiver Collaris on.
The Receiver |-|f the Indicator Light does not come on when any
Collar is not buttonis pressed onthe remote, ensure thatthe
responding to | batteries are charged properly.
the Remote. «If the first two solutions did not resolve your problem,
Refer to “Pair the Remote and the Receiver Collar”.
11