Patpet p-collar 301 User manual

p-collar 301
Please read the quick start before beginning.
0.3.0.02.310210-28-40

Patpet dog training collar is designed to let dogs live safely, happily
and get along with people more harmoniously.
1
Important Safety Information
Do not use with aggressive do g s .
Aggressive dogs can cause severe injury and even death to their owner
and others. If you are unsure whether this product is appropriate for
your dog, please consult your veterinarian or certified trainer.
Safety during on-leash tr a i n i n g .
It is vitally important that you and your dog remain safe while learning
during on-leash training. Your dog should be on a strong leash, long
enough for him to attempt to chase an object, but short enough for him
not to reach a road or other unsafe area. You must also be physically
strong enough to restrain your dog when he tries to chase.
Risk of skin damage.
Please read and follow the instructions in this manual. Proper fit of the
collar is important. A collar worn for too long or made too tight on the
pet’s neck may cause skin damage ranging from redness to pressure
ulcers. This condition is commonly known as bed sores.
Avoid leaving the collar on the dog for more than 12 hours per day.
When possible reposition the collar on the pet’s neck every 1 to 2
hours.
Never connect a lead to the electronic collar; it will cause excessive
pressure on the contacts.
If a rash or sore is found, discontinue use of the collar until the skin
has healed.
If the condition persists beyond 48 hours, see your veterinarian.
This product is not a toy, please keep away from children.
This product is only for use with healthy dogs.

Remote
Overview
LED Indicator
Tone Button
Level +
Level –
Vibration Button
Vibration Level Display
On/Off Button
Channel Conversion Button
Press and Hold it for setting
Vibration&Shock Level
Shock Button
DisplayBattery Capacity
Channel Display
. Contact Points
. Conductive Silicone Covers
. LED Indicator
. On/Off Button
Receiver Collar
2
r
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
PQ
High Shock Level Warning
Shock Level Display
A
B
C
D
E
F
G
H
I
J
K
L
M
.
.
.
.
.
.
.
.
.
.
.
.
.
N
O
P
Q

Setting Up the Product
Before you can use the Dog Training Collar, you
must set up the product using the steps below:
1. Prepare the Remote--install batteries and turn it on.
2. Prepare the Receiver Collar--install batteries, Contact Points,
3. Function test --test function of buttons before putting it on dog.
4. How to Use the Test Lamp--use the Test Lamp to test Shock function
or use as a screw driver.
5. Pair the Remote and the Receiver Collar--Pair them when the receiver
loses connection with the remote , add another receiver, or after
change batteries.
1. Push out the battery cover to remove it(1A).
2. Install the battery according to the engraved mark,
negative (-) fi rst, positive(+) next(1B).
3. Install the battery cover on the Remote(1C).
Install battery on the Remote
1A
+
+
Prepare the Remote
Turn ON/OFF the Remote
1. Press the ON/OFF Button on the Remote once to turn it ON.
2. LCD will be lighted, and show the information of current channel,
battery power and levels. If not, please check the batteries position
or change new batteries.
3. Press and hold the ON/OFF Button on the Remote to turn it OFF until
t h e L C D d i s p l a y g o e s o ff, then release. It may take 2-3 seconds.
3
1B 1C
Note: When the remote is on, the LCD display will appear when any
button is pressed.
Conductive Silicone, then assemble them, turn the Receiver Collar on.

r
1. If the conductive screws are on , remove them first. Pop out the
battery cover to remove it(2A).
2. Install the battery according to the engraved mark(2B).
3. Install the battery cover on the Receiver Collar(2C).
Prepare the Receiver
Install battery on the Receiver
+
+
Assemble Collar Strap
1.Unhitch the nylon belt and take off the Slide Buckle(4A).
2.Thread the strap through the Receiver Collar(4B).
3. Thread the slide buckle through the strap(4C).
4. Thread the strap through the side release buckle(4D).
5. Thread the excess strap through the slide buckle to make
sure the collar strap is surely tight(4E). 4
2A 2B 2C
3A 3B
Install the Contact Points & Conductive Silicone
1. Select the correct Contact Points and length forConductive Silicone
your dog’s coat type:
For dogs with thicker coats, Use 2pcs longer Contact Points and
Conductive Silicones.
For dogs with shorter coats, Use 2pcs shorter Contact Points and
Conductive Silicones.
Note:
1.Don’t install the Metal Contact Points when shock function is not used.
2. Insert the Contact Points into the ports of the collar, use the Test
Lamp to rotate clockwise to tighten them(3A).
3. Install the Conductive Silicone onto the Contact Points to make it
softer, which will be better for dog’s skin(3B).
3
3
.

NOTE: To extend the life of the batteries, please turn the Receiver Collar
off when it is not in use. Remove the battery if you don’t use it for a long
time.
Turn on the Receiver Collar
Press the On/Off Button the Green LED light comes on.
In normal mode, the Green LED will flash every 4 seconds, indicating the
Receiver Collar is on and ready to receive signal from the Remote.
Tu r n o ff t he Receiver Collar
Press and hold the On/Off Button until the Red LED light shuts off
(This takes approximate 3 seconds).
Release the On/Off Button.
Function Test
We recommend you experience the different shock/vibration levels
firsthand on yourself. Please begin at the lowest level, then increase
level gradually to your personal comfortable level .You can do as b e l ow.
5
4A 4B 4C
4D 4E 4F
1. Place one finger over both contact points of the training collar.
2. Hold your remote approximately 2 ft from the receiver collar. Press
the Vibration Button continuously for 1 to 2 seconds. You should feel
continuous vibration.
4. Increase the level until the sensation begins to feel uncomfortable.
3. Press and hold for about 5 seconds until the Shock icon flashes,
press +/- to adjust levels.
d.

6
.
Decrease the Shock/Vibration Level.
The Shock Level can be adjusted from 1 to 16 levels and the Vibration
Level from 1 to 8 levels; please adjust it properly as per your dog’s
reaction.
Don’t press and hold the Vibration/Shock Button too long, to avoid
physical or psychological hurt to the dog.
Note:
Ho w to Us e the Test Lamp
1. Tur n o n the Receiver Collar.
2. Hold th e Test Lam p c o n t a c t s against the Contact Points (o r
3. Press t h e S h o c k B utton and the Test Lamp will be lighted. It wi l l b e
Shock Function Test
increase the Shock/Vibration Level.
Vibration: send vibration command ranging1-8 to the
Receiver Collar.
Tone: send a tone with non-adjustable level to the Receiver
Collar.
Shock: sends shock command ranging 1-16 to the Receiver
Collar. Warning sign will show when the level is over 8.
Channel Conversion: Press shortly once to swtich dog and
dog channel. Vibration & Shock Level Adjustment:
Press and hold for about 5 seconds until the Vibration/Shock
Level display flashes, press +/- to adjust levels.
Conductive Silicone Covers).
brighte r a s t h e S h o ck Level is increased.
Press and hold until the Vibration/Shock Level display flashes to
set Vibration/Shock Level.
NOTE: Continuous stimulation will transmit for no more the 10 continuous
seconds. To reactivate, release and repress the button.