Patriot Lighting DJ3825 User manual

Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
Sku Number: 356-1123
OUTDOOR WALL LANTERN
Model Number: DJ3825
Page 1 of 3
190718
HARDWARE CONTENTS Note: Hardware not shown actual size.
Cross Bar Unit
X1
Mounting Screw
X2
Wire Connector
X3
Ball Nut
X2
Rubber Pad
X2
AA
BB
CC
DD
EE
PACKAGE CONTENTS
A

Page 2 of 3
190718
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters,
Safety Glasses, Ladder, Wire Stripper.
ASSEMBLY INSTRUCTIONS
PREPARATION
Turn off the power at fuse or circuit box.
2. Attach the cross bar unit (AA) to
the outlet box using two mounting
screws (BB). Adjust the length of
the preinstalled headless screws
if necessary.
Note: Make sure that the
headless screws are lined up
horizontally to make the fixture
level.
AA
BB
2
Headless Screw
1. Unscrew the two ball nuts (DD).
Remove the two rubber pads
(EE) and the cross bar unit (AA)
from the backplate (A).
4. Attach the backplate (A) of the
fixture to the cross bar unit (AA)
by aligning and inserting the two
headless screws from the cross
bar unit (AA) into the open holes
on the backplate (A), then place
the two rubber pads (EE) over
the exposed headless screws
before screwing the two ball nuts
(DD).
Note: With silicone caulking compound, caulk
completely around where the backplate meets with
the wall surface to prevent water from seeping into
the outlet box.
3. Pull out the source wires from the
outlet box. Make wire connections
using wire connectors (CC) as
follows:
• Connect the hot wire (usually
black insulation) from the fixture
to the black wire from the power
source.
• Connect the neutral wire (usually white insulation) from
the fixture to the white wire from the power source.
• Attach the fixture grounding wire (usually green
insulation or bare wire) to the cross bar unit (AA) with
the green grounding screw, then connect it to the
house grounding wire with the wire connector (CC).
Carefully put all of the wires back into the outlet box.
3
AA
CC
Green Grounding
Screw
WARNING
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
●All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
●Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
●If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and
electrical rating required.
DD
EE
A
AA
1
DD
EE
A
AA
4

Page 3 of 3
190718
ASSEMBLY INSTRUCTIONS (continued)
5. Install a bulb (not included).
See relamping label at socket
area or packaging for maximum
wattage allowed .
Turn on the power at fuse or circuit box.
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
Spare Parts List:
Assembly Kit
6142MM (1 SET)
●Toclean, turn off and wipe with a damp, non-abrasive cloth.
1) Thelight does not come on at all:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when lightis turned on.
Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R
Cross Bar Unit
X1
Mounting Screw
X2
Wire Connector
X3
Ball Nut
X2
Rubber Pad
X2
AA
BB
CC
DD
EE
5
Max.60W Type A Bulb
(not included)