Patriot Lighting LPT-1108 User manual

Page 1
INSTRUCTIONS FOR LED WALL
LANTERN, MODEL LPT-1108

Thank you for purchasing this Langport Lighting LED wall lantern. This product has been
manufactured with the highest standards of safety and quality.
FEATURES:
•Questions, Problems, Missing Parts? Please contact our Customer Service Team at 1-
877-698-2157. Customer service hours are Monday through Friday, between 8 AM and
5 PM Pacific time. You may also contact us via fax at 1-310-886-3719 or e-mail at
[email protected]m.
•KEEP this instruction manual.
•KEEP your receipt for proof of purchase.
GENERAL:
TOOLS AND ITEMS REQUIRED FOR INSTALLATION AND
ASSEMBLY (NOT INCLUDED):
SAFETY
GOOGLES
WIRE STRIPPERS
#2 PHILIPS
SCREWDRIVER
ELECTRICALTAPE WIRE CUTTERS
PLIERS
Page 2
•Easy to install
•Energy-saving LED lights
•Solid cast aluminum to resist the elements
NOTE: This product is an LED light fixture. It contains its own LED light sources and does
not require the purchase of light bulbs.
.

PARTS:
Remove fixture and mounting package from box and make sure that parts are are not
missing by referencing illustrations below. (Parts are not to scale.)
Page 3
MAIN
FIXTURE
BODY
MOUNTING
BRACKET
BRACKET
MOUNTING
SCREWS (2)
WIRE NUTS
(2)
HEX
NUTS (2)
FIXTURE
MOUNTING
SCREWS (2)
LOCK
NUTS (2)

ASSEMBLY AND INSTALLATION:
CAUTION:
•All electrical connections must be in accordance with local and National Electrical Code
(N.E.C.) standards. If you are unfamiliar with proper electrical practices, obtain services
of a qualified electrician.
•Turn off the main power at circuit breaker before installing fixture, in order to prevent
possible shock.
•Before cleaning fixture, turn off power and allow several minutes for the fixture to cool
down.
BEFORE YOU BEGIN:
Page 4
•The OUTLET BOX described in the following section is not provided. To install this
fixture, a standard OUTLET BOX needs to be pre-installed at the selected mounting
location. Power supply wires need to be run into the OUTLET BOX, extending
approximately 6”from its opening. If an OUTLET BOX does not exist, contact a
qualified electrician to have one installed.
1. DISCONNECT POWERAT THE CIRCUIT BREAKER.
2. Thread the FIXTURE MOUNTING SCREWS into the provided holes of the MOUNTING
BRACKET, as shown. Thread the HEX NUTS onto the FIXTURE MOUNTING SCREWS, as
shown. Do not tighten the HEX NUTS at this time. (Fig. 1)
3. Pull the power supply wires out from the OUTLET BOX, and attach the MOUNTING BRACKET
to the OUTLET BOX, using the BRACKET MOUNTING SCREWS. (Fig. 1)
4. Strip approximately ¼” of insulation from each supply wire from the OUTLET BOX. Raise the
MAIN FIXTURE BODY to the wall, bringing the WALL PLATE close to the OUTLET BOX. Make
the following wire connections using the WIRE NUTS (Fig. 1):
WHITE (NEUTRAL) SUPPLY WRE to WHITE FIXTURE WIRE
BLACK (HOT) SUPPLY WIRE to BLACK FIXTURE WIRE
SUPPLY GROUND WIRE to FIXTURE GROUND WIRE
Wrap each wire connection with 2”of electrical tape.
5. Place the WALL PLATE over the OUTLET BOX, making sure the FIXTURE MOUNTING
SCREWS feed through the holes on the WALL PLATE. Adjust the FIXTURE MOUNTING
SCREWS until they protrude out from the WALL PLATE ¼”.Remove the WALL PLATE and
secure the position of the FIXTURE MOUNTING SCREWS by tightening the HEX NUTS
against the MOUNTING BRACKET. (Fig. 1)
6. Carefully tuck all WIRES and WIRE NUTS into the OUTLET BOX. Place the WALL PLATE
back onto the FIXTURE MOUNTING SCREWS, and secure it into place using the LOCK NUTS.
(Fig. 1)

Page 5
ASSEMBLY AND INSTALLATION (CONT.):
7. After installing the fixture, caulk the upper 2/3s of the WALL PLATE to the mounting surface.
Leave the bottom 1/3 un-caulked to allow for drainage of any water that might leak into the
enclosure. The manufacturer recommends a non-drying exterior caulking material. A good
example is a clear silicone rubber sealant for exterior use.
8. RESTORE POWERAT THE CIRCUIT BREAKER. Turn on the wall switch.
WHITE
(NEUTRAL)
SUPPLY
WRE
WHITE
FIXTURE
WIRE
BLACK (HOT)
SUPPLY WIRE
BLACK
FIXTURE
WIRE
WIRE
NUT
WALL
PLATE
SUPPLY
GROUND
WRE
OUTLET
BOX
FIXTURE
GROUND
WIRE HEX
NUT
BRACKET
MOUNTING
SCREW
MOUNTING
BRACKET FIXTURE
MOUNTING
SCREW
LOCK
NUT
Fig. 1

Page 6
TROUBLESHOOTING:
•To clean the fixture, disconnect power to the fixture by turning off the circuit breaker or
by removing the fuse at the fuse box.Wait a few minutes for the fixture to cool down.
Use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe
the glass and surface of the fixture.
•Do not use any cleaners with chemicals, solvents or harsh abrasives. If necessary, use
a mild soap to clean off any dirt or stains.
PRODUCT MAINTENANCE:
THREE YEAR LIMITED WARRANTY
Patriot Lighting  warrants this product to be free from defects in material and
workmanship for three years from the original date of purchase by the consumer. This
warranty is limited to the counter replacement at the time of purchase, with the original
purchase receipt. Patriot Lighting  will not be liable for the loss or damage of any kind,
incidental or consequential damages of any kind, whether based on warranty contract or
negligence, and arising in connection with the sale, use or repair of the product claimed to
be defective. Some states do not allow the exclusion or limitation of incidental or
consequential damages so the above limitation may not apply to you. This warranty gives
you specific legal rights and you may also have other rights, which vary from state to state.
Misuse, accident, improper installation or maintenance will also void the warranty.
1. Power is off. 1. Make sure power supplyis on.
2. Faultyswitch. 2. Test or replace switch.
3. Faultywire connection. 3. Check wiring.
Fuse blows or circuit
breaker trips when light is
turned on.
1. Crossed wires or power wire is
grounding out.
1. Check wire connections.
Lights will not turn on.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
DISCLAIMER
•Reorient or relocate the receiver antenna.
•Increase the separation between the equipment and receiver.
•Install the product onto on a circuit different from that to which the receiver is connected.
•Consult with the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes made to the electronics circuit will void this equipment’s
compliance with Part 15 of the FCC Rules and should not be operated.
Page 7

Page 8