Patriot Lighting 33573-MND User manual

Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 1-800-660-5391, 8 a.m. - 6 p.m., EST, Monday, 8 a.m. -5 p.m., EST, Friday.
33573-MND
3563806
If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails due to a defect in material and workmanship within five (5) years from the date of original
purchase, simply bring this light fixture with the original sales receipt back to your nearest
MENARDS retail store. At its discretion, PATRIOT LIGHTING agress to have
the product or any defective part(s) repaired or replaced with the same or similar
PATRIOT LIGHTING product or part free of charge, within the stated warranty period,
when returned by the original purchaser with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does not cover
damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to persons/property or costs. This warranty does give you specific legal
rights and you may have other rights, which vary from state to state. See inside installation instruction for full terms and co nditions
FIVE-YEAR LIMITED WARRANTY
WALL LANTERN

,,
- Prior to installation of this fixture or removal of a previous fixture, disconnect the power by turning off
the circuit breaker or by removing the fuse at the fuse box.
Use bulbs specified by the marking and/or labels on the fixture. Consult a qualified electrician to ensure correct
branch circuit conductor.
- Consult a qualified electrician for installation of this fixture.
- Read all instructions before installing.
There are too many items on
1. Bulb is burnt out
Bulb will not light.
Fuse blows or the circuit breaker trips
when light is turned on.
2. Power is off
3. Faulty wire connection
4. Faulty switch
one circuit Unplug the other items on the circuit
Please read and understand this entire manual before attempting to assemble operate or install the product.
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
RISK OF FIRE
This product must be installed in accordance with the applicable installation code by a person familiar with the contruction and
operation of the product and hazards involved.
- Turn off the fixture before replacing the bulb(s)
Wipe clean using soft, dry cloth or static duster.Always avoid using harsh chemicals and abrasivves to clean fixture as they may
damage the finish.
1. Replace light bulb
2. Check power supply
3. Check wiring
4. Test or replace switch
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
CARE AND MAINTENANCE
TROUBLESHOOTING
SAFETY INFORMATION

Wire Connector
2
Outlet Box Screw
Ground Screw
2
Mounting Screw
1
Universal Crossbar
3
1
DDCCAA BB
3
AA
BB
CC
EE
DD
EE
Estimated Assembly Time: 45-60 minutes
PREPARATION
TOOLS REQUIRED
To avoid damaging the product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects
such as the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the
wire, do not continue the assembly process.
PRE-INSTALLATION
Flathead
screwdriver
Phillips
screwdriver
Pliers Electrical tape Wire cutters Drill
HARDWRE INCLUDED
Hardware not shown to actual size

AFixture Body 1
PACKAGE CONTENTS
A

BB
EE
DD
CC
1. Secure the crossbar (EE) to the outlet box (not included) with
the outlet box screws (BB).
2. Attach the ground fixture wire to either green ground screw (CC)
on crossbar (EE) or to the ground wire in the outlet box
(usually GREEN or BARE).
If attaching to the ground wire in the outlet box, fasten together
with a wire connector (DD) and tightly wrap with electrical tape
(not included).
Important: It is important that the outlet box in your
home is properly grounded.
ASSEMBLY INSTRUCTIONS
Connect the neutral(WHITE or RIBBED side) fixture wire to
the neutral (usually WHITE) wire from the outlet box.
Fasten wires together with a wire connector (DD) and tightly
wrap wire connector (DD) with electrical tape
Connect the hot (BLACK or SMOOTH side) fixture wire to the hot
(usually BLACK) wire from the outlet box.
Fasten wires together with a wire connector (DD) and tightly
wrap wire connector (DD) with electrical tape.
EE

ASSEMBLY INSTRUCTIONS
3. Mount the fixture body (A) over the crossbar (EE),
and rotate it clockwise and secure two mounting
screws (AA) by a screwdriver (not included).
EE
A
AA
AA