Patriot Lighting MND2523C User manual

SKU NUMBER: 356-3411
WALL LANTERN
MODEL NUMBER: MND2523C
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - , 7:00 a.m. - 4:00 p.m., CST.Friday
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
AFixture Body 1pc
1
A
Stock Part#
913569KIT
N/A
AA
BB
CC
DD
Crossbar Assembly
Wire Connector
Outlet Box Screw
Mounting Screw
1pc
3pcs
2pcs
4pcs
BB
DD
CC
AA
REVISED 2017-06-23
B
C
BCage 1pc
C4pcs
Glass Panel
(Pre-assembled to Cage) G13564PA
EE
EE Lock Screw 2pcs

SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
● Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing
fuse (or switching off circuit breaker).
Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit
wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,
which could cause serious injury or death from electric shock
WARNING:
CAUTION:
●
● All electrical connections must be in agreement with local codes, ordinances or the national electric
code (NEC). Contact your municipal building department to learn about your local codes, permits
and/or inspections.
● Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a
qualified electrician before installation.
● Do not connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your
lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified,
licensed electrician for information with regards to proper grounding methods as required by the local
electrical code in your area.
● If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct
type and electrical rating required.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare
parts with package contents list and diagram on previous page. If any part is missing or damaged, do not
attempt to assemble, install or operate the product. Contact customer service for replacement parts
Tools Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Electrical tape,
Safety goggles, Silicone sealant.
Bulb Recommended: (1) 75W Type-A medium base bulbs, Alternate (1) LED bulb.
PREPARATION
HARDWARE CONTENTS Note: Hardware shown is not actual size.
Crossbar
x1
Wire Connector
x3 Outlet Box Screw
x2
AA BB CC
2
Mounting Screw
x4
DD Lock Screw
x2
EE

ASSEMBLY INSTRUCTIONS
3
Backplate
STEP 4:
a. Line up holes on the backplate and mounting
holes on the folded edge of the crossbar(AA).
b. Secure by threading mounting screws(DD) into the
mounting holes on the crossbar (AA). Do not fully
tighten.
c. Once all screws are threaded into the crossbar,
tighten with screwdriver.
DD
AA
STEP 2:
Note: Prior to installation, place a towel or thick
cloth under the installation site to prevent loss of
mounting hardware if dropped.
a. Remove the Crossbar (AA) from the Backplate on
the Fixture Body (A) as shown in STEP 4.
b. Align cross bar (AA) to the outlet box so that the
mounting holes on the cross bar (AA) are on the
.
c. Secure the Crossbar (AA) to the outlet box (not
included) with Outlet Box Screws (CC).
side
STEP 5:
a. Install correct bulbs referring to fixture markings
and/or labels for maximum wattage.
STEP 1:
a. Remove the Styrofoam from the Cage (B).
b. Attach the Cage (B) onto the Fixture Hood and
secure with Lock Screws (EE). Hand-tighten until
snug.
B
Outlet Box
AA
CC
WHITE
BLACK (OR RED) WIRE
WHITE
BLACK
FROM SUPPLY
FROM SUPPLY
FROM FIXTURE
FROM FIXTURE
STEP 3:
* Use Wire Connectors (supplied) to connect the
wires.
a) Ground Wire:
1. Wrap supply around
on mounting bracket, no less than 2 inches
from the end of the wire. Tighten .
2. Connect fixture to
wire with wire connector.
b) Supply Wire:
1. Connect the to the
with wire connector.
2. Connect the wire to the
with wire connector.
3. Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the outlet box.
ground wire green ground
screw
ground screw
ground wire supply ground
supply white wire white
fixture supply wire
supply black (or red)
black fixture supply wire
GROUND WIRE
GROUND WIRE
FROM SUPPLY
FROM FIXTURE
GREEN GROUND SCREW
EE
Styrofoam
Fixture Hood

ASSEMBLY INSTRUCTIONS
4
STEP 6:
NOTE: To ensure proper moisture drainage, do not
seal bottom of fixture backplate.
a. Make sure the surface of the exterior wall and
fixture backplate are free of dirt.
b. Using silicone sealer (not included) start on one
side of fixture backplate and follow contour
where the fixture backplate meets the exterior
wall surface.
c. Proceed to seal around backplate.
d. Place silicone sealant over the head of each
mounting screw and mounting holes on the
backplate.
Silicone Sealer
Exterior Wall Surface
Fixture Backplate
Your installation is now complete! Restore
electricity and save this sheet for future reference.
CARE AND MAINTENANCE
TROUBLESHOOTING
1) The light does not come on at all:
2) Fuse blows or circuit trips when light is turned on.
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
a) Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
• To clean, turn off and wipe with a damp, non-abrasive cloth.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-645-3184,
Monday - , 7:00 a.m. - 4:00 p.m., CST.Friday
Glass Replacement
a. Remove the Tabs at the top of the Cage by
removing the four Tab Screws.
b. Replace Glass Panels from the Cage then
re-install the Tabs. Secure with removed
Tab Screws.
Tab Screws
Tabs
Glass Panels
Cage
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING
lighting fixture breaks or fails due to a defect in material and workmanship within five (5)
years from the date of original purchase, simply bring this lighting fixture with the
original sales receipt back to your nearest MENARDS retail store. At its discretion,
PATRIOT LIGHTING agrees to have the product or any defective part(s) repaired or
replaced with the same or similar PATRIOT LIGHTING product or part free of charge,
within the stated warranty period, when returned by the original purchaser with original
sales receipt. This warranty; (1) excludes expendable parts including but not limited to
light bulbs; (2) does not cover damage that has resulted from abuse or misuse; and (3)
does not cover any losses, labor,injuries to persons/property or costs. This warranty
does give you specific legal rights and you may have other rights, which vary from state
to state.
®
®
®
®