Patriot Lighting MH190 User manual

210619
SKU Number: 351-8772
3-LIGHT VANITY LIGHT
Model Number: MH190
PACKAGE CONTENTS
HARDWARE CONTENTS
Mounting Plate Unit
X1
Mounting Screw
X2
Wire Connector
X3
Set Screw
X2
AA
CC
BB
DD
C
B
A
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
Note: Hardware not shown actual size.
Fixture Screw
X9
EE

Page 2 of 4
210619
Turn off the power at the fuse or circuit box.
1. Attach the mounting
plate unit(AA) to the
outlet box using two
mounting screws(BB).
Note: Make sure that
the two holes on the
side of the mounting
plate unit(AA) are
lined up vertically to
make the fixture level.
1
BB
AA
Outlet Box Green Ground Screw
2. Pull out the source
wires from the outlet
box，make wire
connections using
wire connectors(CC)
as follows:
---Connect the black
(hot) wire from the
fixture to the black
(hot) wire from the
power source.
---Connect the white(neutral) wire from the fixture to
the white(neutral) wire from the power source.
2
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
PREPARATION
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Slotted Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire
Cutters, Safety Glasses, Ladder, Wire Stripper.
ASSEMBLY INSTRUCTIONS
SAFETY INFORMATION
---Attach the fixture ground wire (bare wire) to the
mounting plate unit(AA) with the green ground screw,
then connect the fixture ground wire to the house
ground wire with a wire connector(CC).
Carefully put all of the wires back into the outlet box.
AA
CC

Page 3 of 4
210619
ASSEMBLY INSTRUCTIONS (continued)
4. Attach the metal
rings(B) and glass
shades(C) to the
glass holders, and
align holes of glass
shades(C) and
metal rings(B) to
glass holders, then
secure them with
fixture screws(EE).
5
34
3. Attach the backplate
(A) of fixture to the
mounting plate unit
(AA) by aligning the
two holes on the side
of backplate(A) to the
two holes on the side
of mounting plate unit
(AA), then secure
the backplate(A) with
two set screws(DD)
AA
DD
C
EE
B
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
Spare Parts List:
Assembly Kit
6415MM(1 SET)
Glass Shade
10269SC
C
5. Install 3x60W medium
base bulbs(Type T or ST,
not included).
See relamping label at
socket area or packaging
for maximum allowed
wattage.
A
Mounting Plate Unit
X1
Mounting Screw
X2
Wire Connector
X3
Set Screw
X2
AA
CC
BB
DD
Fixture Screw
6426FS
EE
Medium base bulb
Max. 60W
(not included)
6
6. This fixture can be
mounted with light
pointed up or down.
Turn on the power at
the fuse or circuit box.
Glass Holder

Page 4 of 4
210619
To clean, turn off and wipe with a damp, non-abrasive cloth.
1) The light does not work:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when light is turned on.
Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor,injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R