Patton electronics 574 User manual

USER
MANUAL
MODEL 574, 576, 578,
584, 586, 588
Standalone Hub
100Base-T (CAT-5)
Surge Protectors
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com
Part# 07M57x/58x-A
Doc# 074100UA
Revised 10/18/96
An ISO-9001
Certified Company

2
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is warrant-
ed for One Year parts and labor. If any questions or problems arise
during installation or use of this product, please contact Patton
Electronics Customer Service at [phone].
2.1 FEATURES
• Optional 4, 6, or 8 port surge protection hubs
• Multi-level surge protection
• Operation at Speeds up to 100 Mbps
• Can support applications having 2, 4, 6 or 8 wire per cable
• EIA/TIA TSB-40A Category 5 Compliant
• N.E.X.T. better than -40 dB at 100 MHz
• Shunts surges directly to chassis ground
• Easy to install
• Made in the U.S. A.
2.2 DESCRIPTION
Devices that connect to Category-5 cabling systems are routinely
threatened by unwanted electrical energy (lightning, AC power induc-
tion, ESD and more). Higher speed devices–such as those operating
at 100 Mbps–are especially vulnerable to the effects of these hazards,
which can include data loss and hardware damage.
The Patton Model 57x and 58x Series Surge Protectors pro-
vide effective surge protection for devices operating in Category-5
Cabling Systems. The Model 57x/58x is specifically designed for
point-of-use installation; the Model 57x/58x is designed to be installed
at the building entrance. Both models use a multi-stage Silicon
Avalanche Diode circuit, and will continue functioning while handling
the appropriate IEC 801.5 surges applicable to their use (see the
tables in Appendix B). Both the 57x/58x will additionally protect
against surges up to and exceeding 2kV/1kA in fail-safe mode.
Models 57x/58x support a wide range of balanced interfaces from
RS-422 to 100Base-T4. Highlights include a low insertion loss (less
than 0.4dB at 100MHz) and minimal near end cross talk (better than
-40 dB at all frequencies up to 100 MHz). Grounding is accomplished
via a braided ground strap that provides a separate unit-rack connec-
tion. The customer is responsible for ensuring a proper rack to earth
ground connection. For proper grounding, the resistance from the sup-
plied ground lug to the rack frame ground should be less han 2.5 mil-
liohms. Contact Technical Support (see Section 1.1 Service) if further
details are needed for this measurement.
Warning: This product will not provide complete protection should
your equipment or building be subject to a direct lightning hit.
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 57x/58x components to be
free from defects, and will—at our option—repair or replace the prod-
uct should it fail within one year from the first date of shipment. This
warranty is limited to defects in workmanship or materials, and does
not cover customer damage, abuse or unauthorized modification. If
this product fails or does not perform as warranted, your sole recourse
shall be repair or replacement as described above. Under no condition
shall Patton Electronics be liable for any damages incurred by the
use of this product. These damages include, but are not limited to, the
following: lost profits, lost savings and incidental or consequential
damages arising from the use of or inability to use this product.
Patton Electronics specifically disclaims all other warranties,
expressed or implied, and the installation or use of this product shall
be deemed an acceptance of these terms by the user.
1.1 SERVICE
All warranty and nonwarranty repairs must be returned freight pre-
paid and insured to Patton Electronics. All returns must have a Return
Materials Authorization number on the outside of the shipping contain-
er. This number may be obtained from Patton Electronics Technical
Service: [phone], http://www.patton.com;
[email protected].
Note: Packages received without an RMA number will not be
accepted.
Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
57x/58x. Technical Service hours: 8AM to 5PM EST, Monday
through Friday.
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Technical
Support.
1

3.0 INSTALLATION
Model’s 57x and 58x surge protectors are easy to install and are
designed to operate transparently to your network. This section
describes cohnnection procedures for both models.
3.1 PRODUCT APPLICATIONS
Both Models 57x and 58x protect all eight pins on the modular
RJ-45 Cat-5 interface, and work in environments with data rates up to
100 Mbps. The following descriptions will give you a general guideline
for installing the units in your Cat-5 environment.
3.1.1 POINT-OF-USE APPLICATION (MODEL 57x)
The Model 57x is designed for installation on LAN equipment in a
typical office environment, as in Figure 1, below. For best results, the
Model 57x should be connected as close as possible to the communi-
cation port of the device to be protected.
Also, the flat braided grounding wire(s) on the Model 57x should
be attached to the grounded metal frame of the device being protect-
ed. If it is not possible to attach it to the equipment being protected,
contact Patton Technical Support (See Section 1.1).
3.1.2 BARRIER APPLICATION (MODEL 58x)
The Model 58x is a more robust protector than the Model 57x,
and is designed for use as a barrier protector on LAN equipment in
campus networks. Applications include: cable runs between buildings;
cable runs between floors on multi-story structures; and as a higher
capacity replacement for the Model 57x.
The Model 58x is also well suited for use in severe lightning areas,
heavy industrial environments, and situations where heavy machinery
is in the direct vicinity of sensitive LAN equipment and cabling. Figure
2 (below) shows a typical application for the Model 58x. For best
results, the braided grounding strap(s) on the Model 58x should be
attached to the grounded metal frame of the device being protected.
When installation is made at a barrier, such as an external wall, the
braided strap must be connected to a nearby electrical ground. If a
nearby electrical ground cannot be located, contact Patton Technical
Support (See Section 1.1).
Model 57x or 58x
To Other
Building or
Wall
Exterior Wall
Electrical Panel
34
Workstation
Workstation
Model 57x or 58x
Typical RS-422/485 Application
Controller
Workstation
Model 570 or 580
Model 570 or 580
Model 570
or 580
Model 580
57x or 58x
Local Hub
Typical 100Base-T Application
To Other
Building or
Wall
Exterior Wall
Electrical Panel
Figure 2. Barrier Application for 58x
Figure 1. Model 57x58x Point of Use Application

3.2 INSTALLATION PROCEDURES
In order to operate as designed, the Model 57x and 58x must be
connected correctly to your Cat-5 network. For the safest installation,
please read all the instructions below and follow them very carefully.
3.2.1 Connecting the Model 57x or 58x to an I/O Port
1. Turn off equipment power and disconnect the existing connection
between the UTP cable and the equipment’s I/O port.
2. Install the surge protector between the incoming UTP line
and the protected equipment, as in Figure 3, below. This
installation requires a straight through Cat-5 patch cable with
modular RJ-45 male connectors . Use shortest length possible.
Note: The ports are bidirectional. Therefore, the input cable must
be directly across from the output cable.on the Model 57/58x.
3. Locate a metal chassis ground. This is often a hex screw on a D-
shell or an AUI connector. Sometimes, a metal backpanel is
attached with screws, one of which can be used with chassis
grounding. If you cannot locate a chassis ground equipment on
your equipment, contact Patton Technical Support (See Section
1.1) to discuss an alternate grounding solution.
4. Connect the braided ground strap directly to chassis ground con-
nection you have located (see Figure 3, above). The best way to
make this ground connection is to attach the braided metal strap
using a hex nut or screw on your protected device.
Caution:Surge energy may run both directions on the ground
strap. To provide the best protection, it is essential that the sup-
plied ground strap on the Model 57x/58x is connected to the chas-
sis ground of the protected device. Do Not lengthen the ground
strap or connect to a ground other than chassis ground unless
instructed to do so by Patton Technical Support.
3.2.2 Connecting the Model 58x at a Barrier (Wall,
Building, Entrance, etc.)
1. Disconnect the UTP cable from the wall jack or patch panel jack.
2. Install the Model 58x between the UTP line and the jack. This
installation requires a straight through Cat-5 patch cable with
modular RJ-45 male connectors.
Note: It doesn’t matter which port the UTP cable plugs into on the
rack, ss long as the input is directly above or below the correspon-
ding output.
3. Connect the ground braid(s) to the rack frame according to Figure
4 connected to earth ground. Do not lengthen the ground strap
or section describes connection procedures for both models.
4. Connect the rack structure frame directly to the earth ground if it is
not already connected. The best way to make this ground con-
nection is to attach a thick braided metal strap earth ground to a
metal panel, a wall plate screw or an electrical panel or subpanel,
using a hex nut or ground screw. Pay close attention to the impor-
tant note in Figure 4. If you cannot locate a nearby electrical
ground, contact Patton Electronics Technical Service (see Section
1.1)
Caution:Surge energy may run both directions on the ground
strap. To provide the best protection, it is essential that the sup-
plied ground strap on the 57x/58x is connected to the chassis
ground of the protected device. Do not lengthen the ground strap
or connect to a ground other than a chassis ground unless
instructed to do so by Patton Technical Support.
6
Figure 3. Installation of Model 57x /58x Surge Protectors.
5
Cat. 5 input
from network
Cat. 5 patch
cable to pro-
tected
equipment
Connection
to chassis
ground

APPENDIX B
INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) COM-
PLIANCE
Meets IEC standards 801.2, 801.4 and 801.5 (CE Mark)
Effective January 1996 the European Economic Community will
require that all electronic devices be tested and comply with all appli-
cable International standards relating to the product type and category
of use. Electromagetic Compatibility Directive 89/336/EEC specifically
addresses communication line surge protection devices, since con-
formity to immunity standard EN50082-1:1992 is mandatory. The
EN50082-1:10992 standard incorporates International Organization for
Standardization (ISO) publications 801.2 and 801.4, which describe
Electrostatic Discharge and Electrical Fast Transient requirements.
ISO 801.5 describes Surge Immunity Requirements and is expected to
be adopted as a mandatory requirement under EN50082-1 by the
Technical Committee. in 1996. Any protector sold into the international
community must meet these standards. This device has been tested*
and found to comply with these standards as evidenced by its CE
mark.
*Note: All test results are for the Model 57x/58x alone , not including
any external patch cables that are connected to the unit.
APPENDIX A
SPECIFICATIONS
Environment: Category-5 Interfaces that utilize the RJ-45
connector, including RS-422, 423, 10Base-
T, Token Ring, Fast Ethernet, 100Base-T,
100Base-T4 and ATM
Connectors: RJ-45 Female
Response Time: Clamped to 13V after 0.1µS
Characteristic Impedance: 100 Ohms
NEXT Loss (worst pair): Better than -40 dB at 100 MHz
Surge Clamping Voltages: Model 57x: 13 V max with 1 KV Input;
Model 58x: 15 V max with 2 KV Input
Surge Rating: IEC 801.5 Standard Level
DC Clamping Voltages: Common Mode to Gnd, 7.5 V (each line)
@ 50 mA; Differential mode, 8.1 V (per
pair) @ 50 mA
Insertion Loss: Less than 0.4 dB (including connector) at all
frequencies
Return Loss: Better than 14 dB on both models
Group Delay: None, 1 MHz to 100 MHz
Series Resistance: Less than 400 milliohms
Grounding: External ground strap provides separate
unit-ground to chassis-ground contact
PC Board Dimensions: 7.0” x 3.0”
Actual Panel Dimensions: 3.47” x 19.0” x 1.1”
Standard Temperatures: 0 - 500C/32 - 1220F
Flame Retardance: Plastic cases meet UL 94-V0 standard
7 8
Class
1 1.0 kV
24 A
2 1.0 kV
24 A
3 2.0 kV
48 A
4 (n/a)
(n/a)
5 4.0 Kv
95 A
Wave (1.2 x 50 µs)
Forms (1.2 x 50 µs)
IEC 801-5 Threat Levels as a Function of Class
Sym. Lines Coupling Mode
Line-GND, Zs=42 Ohms
Figure B-1. IEC Threat Levels as a Function of Class.

APPENDIX C (continued)
TSB-40A COMPLIANCE TESTING RESULTS
TYPICAL ATTENUATION MEASUREMENT
APPENDIX C
EIA/TIA TSB-40A COMPLIANCE
The Model 57x/58x series surge protectors have been designed to
conform to stringent EIA/TIA TSB-40 standards as required for all
Category-5 connecting hardware. These standards specify the capaci-
tance and near end cross-talk (N.E.X.T) to insure proper operation of
ALL connected equipment. Specific test results are shown in the
tables on the following pages*.
TSB-40A COMPLIANCE TESTING RESULTS
TYPICAL NEAR-END CROSSTALK MEASUREMENT
*Note: All test results are for the Model 57x/58x alone , not including any
external patch cables that are connected to the unit.
9 10
SOURCE/VICTIM PAIRS
FREQ 1-2/3-6 1-2/4-5 1-2/7-8 3-6/4-5 3-6/7-8 4-5/7-8 SPEC
MHz dB dB dB dB dB dB dB
1 82.0 85.0 85.0 78.0 84.0 82.0 >65
4 74.0 77.0 85.0 68.0 73.0 71.0 >65
8 69.0 71.0 83.0 62.8 67.0 64.0 62
10 67.0 69.0 83.0 61.0 66.0 63.0 60
16 63.0 66.0 79.0 56.0 61.0 59.0 56
20 65.5 64.0 78.0 57.0 66.0 56.0 54
25 62.0 62.0 77.0 53.0 58.0 56.0 52
31.25 56.1 62.0 75.5 52.0 54.6 53.0 50
62.5 46.0 56.0 74.0 44.5 46.0 47.0 44
100 45.0 48.0 57.0 40.5 42.0 49.0 40
Figure C-1. N.E.X.T. measurements for Patton Model 57x
SOURCE/VICTIM PAIRS
FREQ 1-2/3-6 1-2/4-5 1-2/7-8 3-6/4-5 3-6/7-8 4-5/7-8 SPEC
MHz dB dB dB dB dB dB dB
1 77.0 85.0 85.0 79.0 83.0 81.0 >65
4 70.0 76.0 85.0 68.0 73.0 70.0 >65
8 67.0 70.0 85.0 62.1 67.0 64.0 62
10 67.0 68.0 85.0 61.0 66.0 62.0 60
16 62.0 65.0 83.0 57.0 61.0 58.0 56
20 69.0 65.0 73.0 58.0 63.0 56.0 54
25 59.0 62.0 72.0 53.2 58.0 55.0 52
31.25 57.0 61.0 81.0 51.0 55.0 53.0 50
62.5 51.5 57.0 68.0 45.0 46.0 48.0 44
100 44.0 45.0 54.0 42.0 41.4 49.0 40
Figure C-2. N.E.X.T. measurements for Patton Model 58x
Freq Pins: 1-2 Pins: 3-6 Pins: 4-5 Pins:7-8 Spec
MHz dB dB dB dB dB
1 0.0 0.0 0.0 0.1 0.1
4 0.1 0.1 0.1 0.0 0.1
8 0.0 0.1 0.1 0.1 0.1
10 0.0 0.0 0.1 0.0 0.1
16 0.1 0.1 0.1 0.0 0.2
20 0.1 0.1 0.2 0.0 0.2
25 0.0 0.0 0.1 0.0 0.2
35.25 0.0 0.1 0.2 0.0 0.2
62.5 0.2 0.1 0.3 0.0 0.3
100 0.4 0.3 0.4 0.3 0.4
Freq Pins: 1-2 Pins: 3-6 Pins: 4-5 Pins:7-8 Spec
MHz dB dB dB dB dB
1 0.1 0.0 0.1 0.1 0.1
4 0.1 0.1 0.0 0.1 0.1
8 0.0 0.1 0.0 0.1 0.1
10 0.1 0.1 0.1 0.1 0.1
16 0.1 0.1 0.1 0.1 0.2
20 0.1 0.2 0.0 0.2 0.2
25 0.0 0.1 0.1 0.1 0.2
35.25 0.0 0.1 0.0 0.1 0.2
62.5 0.1 0.2 0.1 0.2 0.3
100 0.4 0.3 0.4 0.3 0.4
Figure C-3. Attenuation Measurements for Patton Model 57x
Figure C-4. Attenuation measurements for Patton Model 58x

Appendix C (continued)
TSB-40A Compliance Testing Results
TYPICAL INSERTION LOSS MEASUREMENT
APPENDIX C (continued)
TSB-40A COMPLIANCE TESTING RESULTS
TYPICAL RETURN LOSS MEASUREMENT
11
Figure C-5. Return Loss Measurements for Patton Model 57x
Figure C-6. Return Loss measurements for Patton Model 58x
12
Freq Pins: 1-2 Pins: 3-6 Pins: 4-5 Pins:7-8 Spec
MHz dB dB dB dB dB
1 34.0 28.0 28.0 29.0 23
4 38.0 38.0 45.0 43.8 23
8 39.0 41.0 42.0 42.0 23
10 38.0 41.0 39.0 39.5 23
16 34.0 35.0 33.0 33.0 23
20 33.7 33.0 31.0 31.6 23
25 31.0 30.0 34.0 30.0 14
31.25 28.1 27.0 28.0 27.8 14
62.5 21.0 22.0 22.0 22.0 14
100 17.0 21.0 18.2 17.8 14
Freq Pins: 1-2 Pins: 3-6 Pins: 4-5 Pins:7-8 Spec
MHz dB dB dB dB dB
1 28.0 28.0 29.0 30.0 23
4 38.0 38.4 47.0 44.5 23
8 39.0 43.8 41.0 41.2 23
10 38.0 44.0 38.0 38.7 23
16 35.0 38.0 30.0 33.4 23
20 33.0 34.0 31.0 31.0 23
25 31.0 31.0 29.0 28.3 14
31.25 29.0 28.0 27.0 28.0 14
62.5 21.8 22.0 21.0 21.0 14
100 17.2 19.3 16.7 17.3 14
Pin Number: DC Resistance
Milliohms
1 180
2 190
3 180
4 190
5 180
6 120
7 190
8 180
Pin Number: DC Resistance
Milliohms
1 180
2 180
3 180
4 190
5 190
6 120
7 180
8 160
Figure C-7. Patton Model 57x Series Insertion Loss Measurement
Figure C-8.Patton Model 58x Series Insertion Loss Measurement

13
Dear Valued Customer,
Thank you for purchasing Patton Electronics products! We do
appreciate your business. I trust that you find this user manual helpful.
We manufacture one of the widest selections of data communica-
tions products in the world including CSU/DSU's, network termination units,
powered and self-powered short range modems, fiber optic modems, interface
converters, baluns, electronic data switches, data-line surge protectors, multi-
plexers, transceivers, hubs, print servers and much more. We produce these
products at our Gaithersburg, MD, USA, facility, and can custom manufacture
products for your unique needs.
We would like to hear from you. Please contact us in any of the fol-
lowing ways to tell us how you like this product and how we can meet your
product needs today and in the future.
Web: http:www.patton.com
Sales E-mail: [email protected]
Support E-mail: [email protected]
Phone - Sales [phone]
Phone - Support [phone]
Fax: [phone]
Mail: Patton Electronics Company
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
We are committed to a quality product at a quality price. Patton
Electronics is BABT and ISO 9001 certified. We meet and exceed the highest
standards in the industry (CE, UL, etc.).
Please contact us and let us know how we may provide you with the
answers to your needs.
Thank you.
Burton A.Patton
Executive Vice President
P.S. Please tell us where you purchased this product.
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________