Patton electronics 515 DB-15 User manual

USER
MANUAL
MODEL 515
DB-15 Surge Protector
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
http://www.patton.com
Part# 07M515-A
Doc# 074220UA
Revised 11/22/96

1.0 WARRANTY
Patton Electronics warrants all Model 515 components to be free
from defects, and will—at our option—repair or replace the product
should it fail within one year from the first date of shipment. This
warranty is limited to defects in workmanship or materials, and does not
cover customer damage, abuse or unauthorized modification. If this
product fails or does not perform as warranted, your sole recourse shall
be repair or replacement as described above. Under no condition shall
Patton Electronics be liable for any damages incurred by the use of
this product. These damages include, but are not limited to, the
following: lost profits, lost savings and incidental or consequential
damages arising from the use of or inability to use this product. Patton
Electronics specifically disclaims all other warranties, expressed or
implied, and the installation or use of this product shall be deemed an
acceptance of these terms by the user.
1.1 SERVICE AND SUPPORT
All warranty and nonwarranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Support: [phone]; http://www.patton.com; or,
[email protected].Notice: Packages received without an RMA
number will not be accepted.Patton Electronics' technical staff is also
available to answer any questions that might arise concerning the
installation or use of your Patton Model 515. Technical Service hours
are 8AM to 5PM EST, Monday through Friday.
1.2 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Technical
Support.
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions arise during
installation or use of the unit, contact Patton Electronics Technical
Support: [phone]; http://www.patton.com; or,
[email protected].
1 2
3.0 PRODUCT DESCRIPTION
The Patton Model 515 DB-15 Surge Protector employs a solid
state hybrid network to guard DB-15 data ports against data loss and
hardware damage due to transient surges. Equipped with one male
and one female DB-15 connector, the Model 515 inserts between the
data cable and DB-15 port. The Model 515 intercepts data line
transients and sends them directly to chassis ground through the metal
D-shell.
Three versions of the Model 515 are available: The Model 515/25
clamps at 18 volts, protects all 15 pins, and is designed for use with
RS-232 interfaces. The Model 515/6 clamps at 7.5 volts, protects all
15 pins, and is designed for use with RS-422, RS-423 and RS-485
interfaces. The Model 515/T1 clamps at 7.5 volts, protects pins 1, 3, 9
and 11, and is designed for use with T1 equipment. All three versions
provide up to 1500 Watts of transient protection.
Warning: This product will not provide complete protection should your
equipment or building be subject to a direct lightening hit.
4.0 SURGE PROTECTION BENEFITS
The method of surge protection used in the Model 515 adds four
benefits to your system:
High Surge Capacity The Model 515 handles up to 1500 Watts
of surge energy without failure.
Quick Response The Model 515 has fast response times (1 pS
at the component level; 0.5 µS installed). Transient surges are
clamped at 18V for RS-232 and 7.5V for RS-422/423/485, and 7.5V for
T1 equipment.
Low Impedance The Model 515 adds minimal load to your
system. It is about the same as a gender changer.
Open Failure The Model 515 fails “open” if your system
experiences a severe transient or power fault above the rated voltage
of the protector. This means that data and surge energy is shunted
directly to chassis ground, rather than being allowed to flow throughout
the system.

5.0 INSTALLATION
The Patton Model 515 is simple to install and requires no user
configuration. Follow these installation steps.
1. Disconnect the DB-15 data cable from the device you are
protecting in a manner consistent with the manufacturer’s
installation instructions.
2. Be sure the metal D-15 connector on the device you are
protecting is connected to frame ground. If not, contact Patton
Technical Support for further instructions.
3. Plug the DB-15 connector of the Model 515 directly into
the DB-15 Serial port of the device you are protecting. Use of
a serial cable reduces the effectiveness of the protection you
would otherwise receive.
4. Re-attach the DB-15 cable to the available DB-15 connector on
the Model 515. The Model 515 is now inserted between the
data port and the data cable, and will provide up to 1500 Watts
of protection to the data port.
Note: We recommend that a Patton surge protector be
connected to the other end of the data cable as well.
3
APPENDIX A
PATTON MODEL 515 SPECIFICATIONS
General
Standards: RS-232, RS-422/423/485, T1
Surge Capacity: 1500 Watts for 1 mS
Connectors: One male and one female DB-15
Compliance: CE marked for EMC directive 89\336\EEC
(ESD/EFT); Compliant with IEC 801-5
(surge)
Model 515/25
Pins Protected: All 15 pins on the RS-232 interface
Response Time: Clamped to + or - 18 volts after 0.5 µS,
400 Amps with a 8/20 µS pulse
Model 515/6
Pins Protected: All 15 pins on the RS-422/423/485 interface
Response Time: Clamped to + or - 7.5 volts after 0.5 µS,
400 Amps with a 8/20 µS pulse
Model 515/T1
Pins Protected: Pins 1, 3, 9 & 11 on the T1 interface
Response Time: Clamped to + or - 7.5 volts after 0.5 µS,
400 Amps with a 8/20 µS pulse
Copyright ©
Patton Electronics Company
All Rights Reserved
4

5
Dear Valued Customer,
Thank you for purchasing Patton Electronics products! We do
appreciate your business. I trust that you find this user manual helpful.
We manufacture one of the widest selections of data communications
products in the world including CSU/DSU's, network termination units,
powered and self-powered short range modems, fiber optic modems, interface
converters, baluns, electronic data switches, data-line surge protectors,
multiplexers, transceivers, hubs, print servers and much more. We produce
these products at our Gaithersburg, MD, USA, facility, and can custom
manufacture products for your unique needs.
We would like to hear from you. Please contact us in any of the
following ways to tell us how you like this product and how we can meet your
product needs today and in the future.
Web: http:www.patton.com
Sales E-mail: [email protected]
Support E-mail: [email protected]
Phone - Sales [phone]
Phone - Support [phone]
Fax: [phone]
Mail: Patton Electronics Company
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
We are committed to a quality product at a quality price. Patton
Electronics is BABT and ISO 9001 certified. We meet and exceed the highest
standards in the industry (CE, UL, etc.).
Please contact us and let us know how we may provide you with the
answers to your needs.
Thank you.
Burton A.Patton
Vice President
P.S. Please tell us where you purchased this product.
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________