Sauder Costa L-Desk 419956 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
For all your
newfangled gadgetry.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-44
Français pg 45-50
Español pg 51-56
Lot # 394629 09/27/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
L-Desk
Costa Collection | Model 419956

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6-44
45-50
51-56
57-58
59
A RIGHT END (1)
B LEFT END (1)
C BOTTOM (2)
D RIGHT UPRIGHT (1)
D24 RIGHT DRAWER SIDE (2)
D25 LEFT DRAWER SIDE (2)
D28 LARGE RIGHT DRAWER SIDE (1)
D29 LARGE LEFT DRAWER SIDE (1)
D78 LARGE DRAWER BACK (1)
D109 DRAWER BACK (2)
D707 LARGE DRAWER BOTTOM (1)
D716 DRAWER BOTTOM (2)
E LEFT UPRIGHT (1)
F BACK (2)
G LEFT MODESTY PANEL (1)
H RIGHT FRONT LEG (2)
I END MOLDING (4)
J BOTTOM MOLDING (2)
K BACK MOLDING (2)
LLONG MODESTY PANEL
MOLDING (2)
M KEYBOARD SHELF (1)
N RIGHT KEYBOARD UPRIGHT (1)
O RIGHT MODESTY PANEL (1)
P LEFT FRONT LEG (2)
Q RIGHT REAR LEG (2)
R LEFT REAR LEG (2)
SSHORT MODESTY PANEL
MOLDING (2)
T ADJUSTABLE SHELF (1)
U LEFT KEYBOARD UPRIGHT (1)
V DRAWER FRONT (2)
W LARGE DRAWER FRONT (1)
X TOP (1)
Y RETURN TOP (1)
Z RIGHT PANEL (1)
AA LEFT PANEL (1)
BB DOOR (1)
Assembly Tools RequiredTable of Contents
Part Identification
419956 www.sauder.com/servicesPage 2
Electric drill with 3/16" bit
(ONLY in indicated step)

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.
A
BC
C
D
E
F
F
G
H
H
I
I
I
I
J
J
K
K
L
L
M
N
O
P
P
Q
Q
R
R
S
S
T
U
V
V
W
X
Y
Z
AA
BB
D109
D109
D716
D716
D707
D24
D24
D28
D29
D78
D25
D25
419956www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CONNECTOR PLATE - 2
14G
(EXTENSION SET SHOWN SEPARATED)
(EXTENSION SET SHOWN SEPARATED)
WIDE EXTENSION
RAIL - 2
CC WIDE EXTENSION
SLIDE - 2
DD EE NARROW EXTENSION
RAIL - 4 FF NARROW EXTENSION SLIDE - 4
FILE ROD - 2
8B
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1 40AZ DRAWER LEFT - 1
FILE GLIDE - 2
15B
12F TWIST-LOCK®FASTENER - 24
10A SLIDE CAM - 6
CAM SCREW - 37
8F
DOOR STOP - 1
4I
WOOD DOWEL - 16
15F
HIDDEN CAM - 37
1F
GLUE - 1
54M
14H HINGE - 2 KNOB SET - 4
136K
419956 www.sauder.com/servicesPage 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" MACHINE SCREW - 4
21S
BLACK 9/16" LARGE HEAD SCREW - 16
1S
SILVER 1-1/8" FLAT HEAD SCREW - 4
10S
GROMMET CAP - 1
1P
18S BROWN 1" FLAT HEAD SCREW - 4
CORD CLIP - 1
4P
3S GOLD 5/16" FLAT HEAD SCREW - 24
METAL PIN - 4
1R
BLACK 1/2" FLAT HEAD SCREW - 4
11S
BLACK 9/16" FLAT HEAD SCREW - 26
32S
GROMMET - 1
10P
CAM COVER - 3
33P RUBBER SLEEVE - 4 2R
BLACK 1-15/16" FLAT HEAD SCREW - 9
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 12
419956www.sauder.com/services Page 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
A
B
(24 used)
12F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (12F)
into the large holes in the ENDS (A and B).
å Repeat this step for the BOTTOMS (C), UPRIGHTS (D and E),
MODESTY PANELS (G and O), and KEYBOARD UPRIGHTS (N and U).
419956 www.sauder.com/servicesPage 6
STOP
If you purchased
the 419958
Hutch, assemble
that unit first.

Step 2
A
D
B
E
å Push thirty-seven HIDDEN CAMS (1F) into the edges of the
ENDS (A and B), UPRIGHTS (D and E), BACKS (F), LEFT
MODESTY PANEL (G), and RIGHT PANEL (Z).
1F
Arrow
(37 used)
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
F
F
G
Z
419956www.sauder.com/services Page 7

Step 3
H
H
P
P
Q
Q
R
R
Z
AA
8F
8F
å Turn thirty-seven CAM SCREWS (8F) into the LEGS (H, P, Q
and R) and PANELS (Z and AA).
(37 used)
419956 www.sauder.com/servicesPage 8

Step 4
å Turn the ENDS (A and B), UPRIGHTS (D and E), and BACKS (F) over.
å Turn twelve BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B),
UPRIGHTS (D and E), and BACKS (F) until the shoulders of the SCREWS rest on the
surfaces of the ENDS, UPRIGHTS, and BACKS.
å NOTE: Do not overtighten the SCREWS.
å Slide the MOLDINGS (I) onto the ENDS (A and B) and UPRIGHTS (D and E). Slide the
MOLDINGS (K) onto the BACKS (F). Line up the grooves in the MOLDINGS over the
heads of the SCREWS in the ENDS, UPRIGHTS, and BACKS.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on again.
The MOLDINGS should be centered over the ENDS, UPRIGHTS, and BACKS.
BLACK 9/16" FLAT HEAD SCREW
(12 used in this step)
32S
Shoulder
Apply pressure with your hands as you
guide the MOLDINGS over the SCREWS
and onto the ENDS, UPRIGHTS, and BACKS.
A
B
D
E
F
Surface
without
HIDDEN
CAMS
F
Surface
without
HIDDEN
CAMS
Surface without
HIDDEN CAMS Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
K
I
I
K
I
I
Shoulder
419956www.sauder.com/services Page 9

Step 5
Shoulder
Apply pressure with your hands as you
guide the MOLDINGS over the SCREWS
and onto the ENDS, UPRIGHTS, and BACKS.
Shoulder
Apply pressure with your hands as you
guide the MOLDINGS over the SCREWS
and onto the ENDS, UPRIGHTS, and BACKS.
å Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the
MODESTY PANELS (G and O) until the shoulders of the SCREWS
rest on the surface of the MODESTY PANELS.
å NOTE: Do not overtighten the SCREWS.
å Slide the SHORT MODESTY PANEL MOLDINGS (S) onto the
MODESTY PANELS (G and O). Line up the groove in the MOLDING
over the heads of the SCREWS in the MODESTY PANELS.
å NOTE: If the MOLDINGS come up o of the SCREWS, remove
them and slide them on again. BLACK 9/16" FLAT HEAD SCREW
(6 used in this step)
32S
Be sure these edges
are even after the
MOLDING is slid on.
Be sure these edges
are even after the
MOLDING is slid on.
G
O
S
S
419956 www.sauder.com/servicesPage 10
Surface without TWIST-LOCK® FASTENERS
Surface without TWIST-LOCK® FASTENERS
Some assembly
(and snacks) required.