PB TEEN Chelsea User manual

Chelsea Platform Bed
Pre-assembly:
•Please read all instructions before
beginning assembly.
•Two-adult assembly is recommended.
•Save all packing materials until assembly
complete to avoid accidentally discarding
smaller parts or hardware.
Parts included:
www.pbteen.com 1
D – Left Side Rail - 1 pc
F – Center Rail - 1 pc
E – Right Side Rail - 1 pc
G – Slat Roll - 1 pc
H – Support Rail - 2 pcs I – Leg- 4 pcs
B – Head Rail - 1 pc
A – Storage - 1 pc C – Foot Rail - 1 pc

Hardware Included:
www.pbteen.com 2
J – Large Bolts (M8)- 8 pcs K – Small Bolts (M6)- 12 pcs
L – Large Spring Washer(M8)- 8 pcs
M – Small Spring Washer (M6)-12 pcs
P – Wood Screw - 32 pcs
Q – Iron Dowel - 12 pcs R – Large Allen Key (M8)- 1 pc
S – Small Allen Key (M6)- 1 pc
N – Large Flat Washer(M8)– 8 pcs O – Small Flat Washer (M6)- 12 pcs
Tools required but not included:
Phillips Head Screwdriver
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove all the parts from the boxes.
2. Determine the desired location of the piece and prepare all parts there before beginning assembly.
3. Assemble the Support Rail (H) to the middle of the Center Rail (F) and the Right Side Rail (E) by
aligning the pre-attached wood dowels on both ends of the Support Rail (H) and inserting them into
the pre-dilled holes on the side of the Center Rail (F) and the Right Side Rail (E). Insert a Small Bolt
(K), Small Spring Washer (M) and Small Flat Washer (O) through the pre-drilled hole on each side of
the Support Rail (H), as shown below. Tighten with the Small Allen Key (S).

4. Assemble the Left Side Rail (D) to the Foot Rail (C) by inserting 3 Iron Dowels (Q) into the pre-drilled
holes of the Left Side Rail (D) and the Foot Rail (C), as shown below. Insert a Large Bolt (J) a Large
Spring Washer (L) and a Large Flat Washer (N) through the pre-drilled holes of the Foot Rail (C) and
into the pre-drilled holes of the Left Side Rail (D). Tighten using the Large Allen Key (R). Repeat this
step with the Head Rail (B) and Left Side Rail (D), as shown in the images below.
4. Insert 3 Iron Dowels (Q) into the pre-drilled holes on the ends of the Foot Rail (C) and Head Rail (B),
as shown below. Attach the Center Rail (F) to the Foot Rail (C) and the Head Rail (B) by inserting the
pre-attached wood dowel of the Center Rail (F) into the pre-drilled hole of the Foot Rail (C) and the
Head Rail (B), as shown below. Insert a Small Bolt (K) a Small Spring Washer (M) and a Small Flat
Washer (O) through the pre-drilled hole on the end of the Center Rail (F) and into the pre-drilled holes
on the side of the Foot Rail (C) and Head Rail (B), as shown below. Tighten with the Small Allen Key
(S).
5. Assemble the Right Side Rail (E) to the Foot Rail (C) and Head Rail (B) by inserting the 3 Iron Dowels
(Q) into the pre-drilled holes of the end of the Foot Rail (C) and the Right Side Rail (F), as shown
below. Insert a Large Bolt (J) a Large Spring Washer (L) and a Large Flat Washer (N) through the
pre-drilled holes of the Foot Rail (C) and into the pre–drilled holes of the Right Side Rail (E). Tighten
using the Large Allen Key (R). Repeat this step with the Head Rail (B) and Left Side Rail (E).
Tighten with the Large Allen Key (R).
www.pbteen.com
3

6. Insert the exposed screw of the Leg (I) into the pre-drilled hole on each corner of the bed rail.
Turn clockwise until tight.
www.pbteen.com 4
7. Turn the Platform Bed upright and assemble the Storage (A) to the bed by placing the Storage
(A) onto the top of the Right Side Rail (E) and Center Side Rail (F), making sure to align the pre-
drilled holes of the Right Side Rail (E) with the pre-drilled holes on the underside of the Storage
(A). Insert a Small Bolt (K), a Small Spring Washer (M) and Small Flat Washer (O) through the
pre-drilled under the Right Side Rail (E) and into the pre-drilled holes of the Storage (A), as
shown below. Tighten with the Small Allen Key (S).

8. Lay the Slat Roll (G) on the inner ledges of the Left Side Rail (D) and the Center Rail (F). Using a
Phillips Head Screwdriver, fasten the Slat Roll (G) onto the rails with 32 Wood Screw (P), as
shown below. Do not fully tighten until all screws are in place.
9. Adjust the levelers on the bottom of all the Legs (I) so that they are in firm contact with the floor.
Care Instructions:
•Avoid direct sunlight and excessive
temperatures.
•Dust often using a clean, soft, dry and lint-free
cloth.
•Slightly moisten cloth with water. A damp cloth
holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.
www.pbteen.com 5